Manuale dell'operatore e dei componenti della fresatrice per legno JET JWS-18HO

Introduzione

This manual provides comprehensive instructions for the safe operation, maintenance, and parts identification of the JET JWS-18HO Wood Shaper. Please read this manual thoroughly before operating the machine to ensure proper use and to prevent injury or damage. Keep this manual accessible for future reference.

This image displays the front cover of the JET JWS-18HO Wood Shaper Operator's Manual. It features the JET logo at the top, followed by 'EQUIPMENT & TOOLS' and 'OPERATOR'S MANUAL'. Below this, the model 'JWS-18HO WOOD SHAPER' is clearly visible. A black and white illustration of the JWS-18HO wood shaper machine is centrally placed, showing its main body and stand. The manual number 'M-708319' is located at the bottom right corner.

Informazioni sulla sicurezza

Seguire sempre le precauzioni di sicurezza di base per ridurre il rischio di incendi, scosse elettriche e lesioni personali. Queste includono, a titolo esemplificativo ma non esaustivo:

• Indossare adeguati dispositivi di protezione individuale (DPI), tra cui protezioni per gli occhi, protezioni per l'udito e maschere antipolvere.
• Assicurarsi che l'area di lavoro sia pulita, ben illuminata e libera da ostacoli.
• Do not operate the shaper in damp o luoghi umidi.
• Tenere i bambini e gli astanti lontani dalla macchina in funzione.
• Disconnect power before making adjustments, changing cutters, or performing maintenance.
• Use push sticks or push blocks when feeding small workpieces.
• Never reach into the cutter area while the machine is running.
• Prima dell'operazione, assicurarsi che tutte le protezioni siano in posizione e funzionino correttamente.

Installazione e assemblaggio

Before operating your JET JWS-18HO Wood Shaper, ensure it is properly assembled and installed. Refer to the exploded view diagrams in the parts section for component identification.

1. Disimballaggio: Rimuovere con attenzione tutti i componenti dall'imballaggio. Verificare che non vi siano danni dovuti al trasporto.
2. Montaggio base: Assemble the stand or base according to the provided hardware and instructions. Ensure all fasteners are securely tightened.
3. Mounting the Shaper: Securely mount the shaper unit to the assembled stand or a sturdy workbench using appropriate bolts and washers.
4. Collegamento elettrico: Connect the machine to a grounded power outlet of the correct voltage as specified in the electrical requirements section (refer to wiring diagram).
5. Controlli iniziali: Verify that all moving parts operate freely and that no components are loose.

Istruzioni per l'uso

Familiarize yourself with the controls and functions of the JWS-18HO Wood Shaper before beginning any work.

Controlli finitiview:

• Interruttore di alimentazione: ON/OFF switch for the motor.
• Blocco del mandrino: Engages to hold the spindle for cutter changes.
• Spindle Height Adjustment: Wheel or lever to raise and lower the spindle.
• Regolazione della recinzione: Knobs or levers to position the fence for desired cut depth.

Funzionamento di base:

1. Installazione della taglierina: Ensure the machine is unplugged. Select the appropriate cutter for your task. Install it securely on the spindle, ensuring proper orientation and tightening.
2. Fence and Spindle Adjustment: Adjust the fence to control the depth of cut and the spindle height to expose the correct amount of the cutter. Perform test cuts on scrap material.
3. Workpiece Feeding: Always feed the workpiece against the direction of cutter rotation. Use push sticks for safety. Maintain a firm grip and consistent feed rate.
4. Raccolta della polvere: Connect a dust collection system to the shaper for a cleaner and safer work environment.

Manutenzione e lubrificazione

Regular maintenance ensures the longevity and optimal performance of your JWS-18HO Wood Shaper. Always disconnect power before performing any maintenance.

• Pulizia: After each use, clean the machine thoroughly, removing sawdust and debris from the table, fence, and motor housing.
• Lubrificazione: Periodically lubricate moving parts such as spindle height adjustment mechanisms and fence slides. Refer to the lubrication points diagram (if available in the full manual) for specific locations and recommended lubricants.
• Ispezione della fresa: Inspect cutters for sharpness and damage. Replace dull or damaged cutters promptly.
• Tensione della cinghia: Check drive belt tension periodically and adjust as necessary to prevent slippage.
• Ispezione elettrica: Controllare regolarmente che il cavo di alimentazione e la spina non siano danneggiati.

Elenco delle parti ed esploso View Diagrammi

This section contains detailed exploded view diagrams and a corresponding parts list to assist with identification and ordering of replacement parts. Each diagram illustrates specific assemblies of the JWS-18HO Wood Shaper, with numbered components corresponding to the parts list.

(Note: Actual diagrams and lists would be included here in a complete manual. For example, a diagram of the spindle assembly with numbered parts, followed by a table listing part numbers and descriptions.)

Risoluzione dei problemi

This section provides solutions to common operational issues. If you encounter a problem not listed here, or if the suggested solutions do not resolve the issue, contact qualified service personnel.

Specifiche

Technical specifications for the JET JWS-18HO Wood Shaper are provided below. These specifications are subject to change without notice for product improvement.

• Modello: JWS-18HO
• Motore: Example: 1.5 HP, 120V, 60Hz, 1 Phase
• Velocità del mandrino: Example: 7,000 / 10,000 RPM
• Diametro del mandrino: Example: 1/2", 3/4"
• Dimensioni della tabella: Example: 20" x 24"
• Altezza tavolo: Example: 34"
• Peso: Example: 250 lbs

Assistenza clienti

For technical assistance, replacement parts, or service inquiries, please refer to the product packaging or the official JET website. Have your model number (JWS-18HO) and serial number ready when contacting support.