Introduzione
This manual provides essential instructions for the safe operation, assembly, maintenance, and parts identification for the Jet JWTS-10JF Table Saw. Please read this manual thoroughly before operating the machine to ensure proper use and to prevent injury or damage.
The Jet JWTS-10JF Table Saw is designed for precision cutting of wood and wood-like materials. Adherence to the guidelines presented herein will maximize the lifespan and performance of your equipment.
Istruzioni generali di sicurezza
Always wear appropriate personal protective equipment (PPE) including safety glasses, hearing protection, and dust mask when operating the table saw. Ensure the work area is clean, well-lit, and free from obstructions. Disconnect power before performing any maintenance or adjustments.
- Leggere e comprendere tutte le istruzioni prima di utilizzare la sega.
- Mantenere le protezioni in posizione e in condizioni di funzionamento.
- Maintain a safe distance from the blade.
- Per i tagli stretti utilizzare uno spingipezzo o un blocco di spinta.
- Assicurarsi che la lama sia affilata e installata correttamente.
- Never reach over or behind the saw blade.
- Securely fasten all components before use.
Installazione e assemblaggio
This section details the assembly process for your Jet JWTS-10JF Table Saw, including unpacking, component identification, and initial setup steps.
Disimballaggio e ispezione
Carefully remove all components from the packaging. Inspect for any shipping damage. Report any damage immediately to your dealer. Verify all parts listed in the parts list are present.
Scomposizione dell'assemblaggio
- Montaggio base: Attach the legs to the base frame using the provided bolts and nuts. Ensure all connections are tight.
- Table Top Installation: Carefully place the main table top onto the base assembly. Secure it with the designated fasteners.
- Installazione del motore: Mount the motor according to the diagram, ensuring proper alignment with the blade arbor.
- Protezione della lama e coltello divisore: Install the blade guard and riving knife. These are crucial safety components and must always be in place during operation.
- Goniometro per recinzione e angolazione: Attach the rip fence and miter gauge. Calibrate them for accurate measurements.
Schema elettrico
Refer to the wiring diagram for proper electrical connection. Ensure the saw is connected to a grounded power source with the correct voltage e amperage as specified on the motor label. If you are unsure, consult a qualified electrician.
(Note: A detailed wiring diagram would typically be provided on a separate page or within the physical manual. For this digital representation, assume a diagram is referenced.)
Istruzioni per l'uso
This section covers the fundamental steps for operating your Jet JWTS-10JF Table Saw safely and effectively.
Prima di iniziare
- Ensure the blade is clean, sharp, and appropriate for the material being cut.
- Adjust the blade height so that it is approximately 1/8 inch above the workpiece.
- Set the rip fence or miter gauge for the desired cut.
- Clear the table of any debris or tools.
- Confirm all safety guards are in place and functioning.
Fare un taglio
- Position the workpiece firmly against the rip fence or miter gauge.
- Accendi la sega e lascia che la lama raggiunga la massima velocità.
- Using a steady, controlled motion, feed the workpiece into the blade. For longer pieces, use outfeed support.
- Always use a push stick or push block when the workpiece is close to the blade or for narrow cuts.
- Once the cut is complete, turn off the saw and wait for the blade to stop completely before removing the workpiece or offcuts.
Image: The Jet JWTS-10JF Table Saw in operation, demonstrating a typical cutting scenario. Note the safety guard in place and the workpiece being fed through the blade.
Manutenzione
Regular maintenance ensures the longevity and safe operation of your table saw. Always disconnect power before performing any maintenance.
Manutenzione giornaliera
- Clean the table surface and blade area of sawdust and debris.
- Inspect the blade for sharpness and damage. Replace dull or damaged blades.
- Check that all guards and safety devices are functioning correctly.
Manutenzione mensile
- Lubricate moving parts as indicated in the parts diagram.
- Controllare e serrare tutti i dispositivi di fissaggio.
- Ispezionare il cavo di alimentazione per eventuali segni di usura o danni.
- Clean the motor vents to ensure proper cooling.
Risoluzione dei problemi
This section provides solutions to common issues you might encounter with your Jet JWTS-10JF Table Saw.
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Saw non si avvia | Nessuna alimentazione, interruttore automatico scattato, interruttore difettoso | Controllare il collegamento dell'alimentazione, ripristinare l'interruttore, ispezionare l'interruttore |
| Blade binds or stalls | Dull blade, improper blade height, workpiece pinching | Replace/sharpen blade, adjust blade height, use riving knife |
| Tagli imprecisi | Fence not parallel, miter gauge misalignment, loose components | Calibrate fence/miter gauge, tighten all fasteners |
| Vibrazione eccessiva | Unbalanced blade, loose motor mounts, uneven surface | Check blade, tighten motor mounts, ensure stable footing |
Specifiche
Key technical specifications for the Jet JWTS-10JF Table Saw.
- Modello: JWTS-10JF
- Diametro lama: 10 inches (standard)
- Motore: (Specific motor details would be here, e.g., 1.5 HP, 120V, 15A)
- Max Depth of Cut at 90°: (e.g., 3-1/8 inches)
- Max Depth of Cut at 45°: (e.g., 2-1/4 inches)
- Rip Capacity Right of Blade: (e.g., 30 inches)
- Rip Capacity Left of Blade: (e.g., 12 inches)
- Dimensioni della tabella: (e.g., 27 x 20 inches)
- Pubblicazione n.: M-708301K
- Data di pubblicazione/revisione: 05/96
Note: Specific motor and cutting capacities are illustrative and should be verified against the actual product specifications. The provided "Item Weight" of 7 ounces refers to the manual itself, not the table saw.
Elenco delle parti
A comprehensive list of replacement parts for the Jet JWTS-10JF Table Saw. When ordering parts, please provide the model number and part number.
(Note: A full parts list with diagrams would typically be included in the physical manual. For this digital representation, a general reference is provided.)
- Blade (10-inch, various tooth counts)
- Assemblaggio della recinzione parallela
- Mitre Gauge
- Gruppo protezione lama
- Coltello Riving
- Spingere il bastone
- Motor (specific model number)
- Interruttore di alimentazione
- Cintura di sicurezza
- Assemblea del supporto conico
Informazioni sulla garanzia
Jet provides a limited warranty for its products. Please refer to the official Jet website or contact customer support for the most current and detailed warranty terms and conditions applicable to your JWTS-10JF Table Saw. Keep your purchase receipt as proof of purchase.
Assistenza clienti
For technical assistance, parts inquiries, or service, please contact Jet customer support. Have your model number (JWTS-10JF) and serial number ready when you call.
- Websito: www.jettools.com
- Telefono: (Refer to Jet's official websito per i numeri di contatto attuali)
- Centri Servizi: Locate authorized service centers via the Jet websito.
