Weiser Augusta/Troy Single Cylinder Handleset

1. Introduzione

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Weiser Augusta/Troy Single Cylinder Handleset. This handleset is designed for residential and light commercial applications, offering security and durability with an ANSI Grade 2 rating. Please read all instructions carefully before beginning installation to ensure proper function and safety.

2. Informazioni sulla sicurezza

• Always wear appropriate safety gear, such as safety glasses, during installation.
• Tenere le parti piccole lontano dalla portata dei bambini per evitare rischi di soffocamento.
• Use only the tools specified or recommended in this manual.
• Ensure all screws are tightened securely, but do not overtighten, as this may damage components.
• If you are unsure about any part of the installation process, consult a qualified locksmith or professional installer.

3. Contenuto della confezione

Verificare che tutti i componenti siano presenti prima di iniziare l'installazione:

• Exterior Handleset Assembly (Augusta/Troy Trim)
• Interior Knob Trim
• Chiavistello a catenaccio
• Chiusura a molla
• Strike Plates (Full Lip)
• Viti di montaggio
• Chiavi
• Modello di installazione (se incluso)

4. Installazione

Strumenti necessari: Phillips head screwdriver, tape measure, pencil, drill (optional for new installations).

Figura 1: Oltreview of the Weiser Augusta/Troy Single Cylinder Handleset components, including the exterior handle, interior knob, and associated hardware.

1. Prepara la porta: Ensure your door has the correct bore holes and backset. This handleset is designed for doors with a 2-1/8 inch cross bore and an adjustable backset of 2-3/8 inches or 2-3/4 inches.
2. Installare il chiavistello a catenaccio: Insert the deadbolt latch into the edge bore hole, ensuring the bolt faces the correct direction. Secure it with the provided screws.
3. Install the Spring Latch: Insert the spring latch into the lower edge bore hole, ensuring the bevel faces the door frame. Secure it with the provided screws.
4. Install the Exterior Handleset: Place the exterior handleset assembly onto the door, aligning the posts with the bore holes.
5. Install the Interior Knob Trim: Attach the interior knob trim to the exterior handleset, ensuring the spindle engages with the spring latch mechanism. Secure with the long mounting screws, tightening evenly.
6. Operazione di prova: Before closing the door, test the deadbolt and spring latch mechanisms to ensure smooth operation. The deadbolt should extend and retract fully with the key from either side. The lower trim is non-locking.
7. Installare le piastre di battuta: Mark and chisel out recesses for the strike plates on the door frame, aligning them with the latches. Secure the strike plates with the provided screws.

5. Funzionamento

• Locking the Deadbolt: Insert the key into the exterior cylinder and turn to extend the deadbolt. From the interior, turn the thumbturn to extend the deadbolt.
• Unlocking the Deadbolt: Insert the key into the exterior cylinder and turn to retract the deadbolt. From the interior, turn the thumbturn to retract the deadbolt.
• Operating the Lower Latch: The lower handle operates a spring latch for entry and exit. This latch does not lock and is always accessible from both sides.

6. Manutenzione

• Pulizia: Clean the handleset with a soft, damp panno. Evitare detergenti abrasivi, solventi o prodotti chimici aggressivi, poiché possono danneggiare la finitura.
• Lubrificazione: Periodically apply a small amount of graphite lubricant or a silicone-based spray to the keyway and internal mechanisms to ensure smooth operation. Do not use oil-based lubricants.
• Ispezione: Regularly check all screws for tightness and ensure the handleset operates smoothly. Tighten any loose screws as needed.

7. Risoluzione Dei Problemi

• Handleset is stiff or difficult to operate:
  • Check if mounting screws are overtightened. Loosen slightly if necessary.
  • Apply lubricant to the latch and cylinder mechanisms.
  • Ensure the door is properly aligned and not binding against the frame.
• Deadbolt does not extend or retract fully:
  • Verify the strike plate alignment. Adjust if the deadbolt is hitting the frame or strike plate.
  • Check for obstructions in the door frame.
• La chiave è difficile da inserire o girare:
  • Applicare lubrificante alla grafite sulla sede della chiavetta.
  • Assicurarsi che la chiave non sia piegata o danneggiata.

8. Specifiche

9. Garanzia e supporto

Weiser products are manufactured to the highest standards and are backed by a limited lifetime warranty on mechanical components and finish. For detailed warranty information, technical support, or to purchase replacement parts, please visit the official Weiser webo contattare il servizio clienti. Conservare la prova d'acquisto per eventuali reclami in garanzia.