iSound Audio Dream Time: High-Performance Bluetooth FM Clock Radio and Bluetooth Speaker

Specifications

• Package Dimensions 
  10.98 x 5.83 x 4.69 inches
• Item Weight 
  2.33 pounds
• Power Source 
  Battery Powered
• Display Type 
  Digital
• Operation Mode 
  Manual
• Alarm Clock 
  Yes
• Brand 
  ISound Audio

Introduction

You can take your audio with you everywhere you go thanks to the sound Hang On Bluetooth speaker. To listen to your favorite music wirelessly, use a Bluetooth-enabled device such as a smartphone, tablet, MP3 player, laptop, or another device.

What’s In the Box?

• HiFT Dream Time
• Charge cable
• Audio cable
• User guide

TOP OF SPEAKER

BACK OF SPEAKER

1. Multifunction button
2. MODE button
3. Track back
4. Track forward
5. Volume down
6. Volume up
7. Charge port (DC5V)
8. LED indicator
9. LINE IN port (wired)
10. ON/OFF switch

Button and port functions

NOTE
Button functions may vary per connected device. Some functions may require multiple presses.

• ON/OFF switch
  To turn the speaker on and off
• Multifunction button
  Play/Pause/Dim LED screen (press and hold for 1 second, then release up to three times)/ Answer calls/End calls/Reject calls (press and hold for 3 seconds)/Mute in AUX IN mode/Change between saved FM channels in FM mode
• MODE button
  To change between 6 modes. Modes include: Clock, Date, Alarm, Bluetooth, FM radio, LINE IN (to connect via audio cable)/To set the time and alarm in Clock and Alarm mode (press and hold for 2 seconds)/ To use Scan and Channel save function in FM mode (press and hold for 2 seconds)
• Track buttons
  To go to the next track and previous track (press up to two times to go to the beginning of the track or previous track)/Change time in Clock and Alarm mode/Change FM radio stations in FM mode
• Volume buttons
  To raise and lower the volume/To set Alarm in Alarm mode
• Charge port
  To charge the speaker
• LINE IN port (wired)
  To play via audio cable

Charging your HiFi Dream Time

NOTE
Make sure your HiFi Dream Time is fully charged before using it the first time.

• Gently plug the Micro-USB end of the included charge cable into the Charge port on the HiFi Dream Time and plug the other USB-A end into a powered USB source.

Charging
LED indicator glows red

Fully charged
The LED indicator glows green

Low battery
(under 10% level)- you will hear 3 beeps

Getting started (first-time use)

• Power on the speaker using the ON/OFF switch.
• Press the MODE button until you hear “Bluetooth mode’
• Select Bluetooth ID “HiFi Dream Time” from your Bluetooth-enabled device.
• To power off the HiFi, Dream Time moves the ON/OFF switch to the “OFF position.

Setting the clock

• Power on the speaker on using the ON/OFF switch.
• Press and hold the MODE button until the year starts flashing: use the Track forward/Trackback buttons to change the year.
• Press and release the MODE button again to change the date; use the Track forward/Track back to change the month, press and release the MODE button again to change the day.
• Press and release the MODE button a third time to change the clock; use the Track forward/Track back to change the hour, press and release the MODE button again to change the minutes.
• When the time is set, press and release the MODE button to enter back into Clock mode.

Setting an alarm

• Press and release the MODE button until you hear “Alarm mode”
• Press and hold the MODE button until the hour numbers start to flash. Use the Track forward/Track back to change the hour; press and release the MODE button again to change
  the minutes.
• Press and release the Volume down button to turn the alarm on or off. You will see an alarm icon with the number “1” when the alarm is on.
• When the alarm is set, press and release the MODE button to exit alarm mode.

Playing via LINE IN (wired)

• Power on the speaker using the ON/OFF switch.
• Plug one end of the included audio cable into the LINE IN port on the back of the speaker, you will hear “LINE IN mode”
• Plug the other end of the cable into your audio device.

Playing in FM mode

• Power on the speaker using the ON/OFF switch.
• Press and release the MODE button until you hear “FM mode’
• Press and hold the MODE button to enter the “Scan and Channel save” function.

NOTES

• Adjust the volume to the desired level on your device before using the HiFi Dream Time.
• You must enter “Bluetooth° mode” in order to play music via Bluetooth° or answer calls.
• You must enter the Scan and Channel save function first to save FM radio stations.
• The speaker will default to Clock mode when the speaker is powered on.
• When the HiFi Dream Time is powered on, your device will automatically find and pair with the HiFi Dream Time after the initial pairing.
• The “10% low battery” indicator only works when the HiFi
• Dream Time is on. If you are unable to find or pair with the HiFi Dream Time, try turning your Bluetooth° off and on.

Important safety precautions

• Recharge the battery every 3 months when not in use to keep the battery in the best condition.
• Incorrect use or incompatibility with your device may result in damage or reduced battery performance.
• Do not attempt to disassemble the product.
• Tampering with your device can result in damage to your product, void of warranty, and could cause injuries.
• Store and operate between 32°F – 113°F.
• Do not place this product near a heat source or flame.
• The internal battery must be recycled or disposed of properly. Contact your local waste management office for information on the proper disposal or recycling.
• Do not Listen at a high-volume level. Extended high volume levels can impair hearing
• Do not use it when a failure to hear your surroundings could be dangerous.

FCC information

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or  television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This equipment may not cause harmful interference
2. This equipment must accept any interference received, including interference that may cause undesired operation.

Warranty information

All isOUND products come with a limited warranty and have been subjected to a thorough series of tests to ensure the highest level of dependability and compatibility. It is unlikely that you will experience any problem, but if a defect should become apparent during the use of this product, iso warrants to the original consumer purchaser that this product will be free from defects in material and workmanship for a period of 120 days from the date of your original purchase.

If a defect covered by this warranty occurs to a product purchased in the U.S. or Canada, isOUND, at its option, will repair or replace the product purchased at no charge or refund the original purchase price. If a replacement is necessary and your product is no longer available, a comparable product may be substituted at the sole discretion of sound. For isOUND products purchased outside of the U.S. and Canada, please ask the store where it was purchased for further information.

Service Information
For service on any defective product under the 120-day warranty policy, please contact Consumer Support to obtain a Return Authorization Number. isOUND reserves the right to require the return of the defective product and proof of purchase.

NOTE
Sound will not process any defective claims without a Return Authorization Number.

Consumer support hotline
877-999-3732 (U.S. and Canada only) or 310-222-1045 (International)

Consumer support email
support@isound.com

Website
www.isound.com

Save a tree, register online

SOUND is making the eco-friendly choice to have all products registered online. This saves the printing of physical paper registration cards. All the information you need to register your
recent iSOUND purchase is available at: www.isound.com/product-registration

Frequently Asked Questions

References

• User Manual