E1-M-D Paste Anywhere Human Motion Sensor Switch
“
Product Information
Specifications
- Input voltage: 5-24VDC
- Output voltage: 5-24VDC
- Output current: 3A
- Output power: 15-72W
- PWM Frequency: 2000Hz
- Operation temperature: -20°C to +55°C
- Safety standard: EN 61347-1/-2, EMC standard: EN 62493, EN IEC
55015/EN IEC 61547, CE, RoHs - Certification Warranty: 5 years
- Features: Human motion sensor switch, built-in 5.8GHz
motion-detecting radar module
Product Usage Instructions
Set Key and Indicator Function
When the light is on, the indicator is brighter; when the light
is off, the indicator is less bright. The factory default light off
delay time is 30s and the sensing distance is 3m. To change the
light off delay time and sensing distance, short press or long
press the set key with the equipped pin.
Sensor Switch Installation
Open Installation: Stick the back of the sensor
switch to the board with 3M adhesive and attach the indicator
sticker to the front.
Concealed Installation: Follow the provided
installation precautions for proper setup.
Sensor Switch Application
Individual Switch Application: Set the delayed
light off time to 30s or 60s for optimal performance. The light
turns on when people come and turns off when people leave.
Multiple Switch Application: Utilize multiple
switches with recommended delayed light off times for efficient
lighting control based on human movement.
FAQ
Q: What should I do if the sensor switch does not detect human
movement?
A: Ensure that the sensor head is correctly installed in the
appropriate direction and angle. Also, verify that there are no
obstructions blocking the sensor’s view.
Q: How do I reset the sensor switch settings?
A: After a power failure, the device automatically restores the
settings. To manually reset, follow the provided instructions for
changing light off delay time and sensing distance.
“`
E1-M(D),E1-M(L)
Paste Anywhere Human Motion Sensor Switch
Sensor
Technical Parameters
Input and Output Input voltage
5-24VDC
Output voltage
5-24VDC
Output current
3A
Output power
15-72W
PWM Frequency
2000Hz
Environment and Protection
Operation temperature
Ta: -20 OC ~ +55 OC
Protection
Reverse polarity
Package
Size
90x130mm
Grossweight
0.036kg
Safety and EMC Safety standard
EMC standard Certification Warranty
EN 61347-1/-2 EN 62493 EN IEC 55015/ EN IEC 61547 CE RoHs 5years
E1-M(D) DC female input DC male output
E1-M(L) Dupont male jack in Dupont female jack out
Features
Paste anywhere human motion sensor switch, 5-24VDC power supply, output connected to low voltage LED strip. Built-in 5.8GHz motion-detecting radar module, can detect human movement through non-metallic materials
such as wood, plastic, glass and acrylic. When detected human movement, the light will turn on; when human movement is not detected,
the light will turn off after the delay is over. Sensor switch detection distance: 0.5-5m, detection angle: 120°. 5 levels of delayed light off time can be set (10s, 30s, 60s, 180s, 300s). 4 levels of sensor distance can be set (5m, 3m, 1.5m, 0.5m). Ultra-thin design, no need to cut holes, random paste installation, can be hidden. Apply to light illumination of cabinets, closets, wine cabinets, staircases, corridors, hallways, and so on.
Dimension
52.00mm
E1-M(D)
Motion Sensing Switch
Uin= 5-24VDC lin= 3.5A Uout= 5-24VDC Iout= 3A Pout= 15W@5V
36W@12V 72W@24V Temp Range: -20~+55
User Manual Ver 1.0.0 2025.6
Back
7.00mm
Wiring Diagram
E1-M(D)
Y
361 361
361 361
AWM 2468 2OAWG
AWM 2468 2OAWG
Power Adapter 5-24VDC
Input (DC female): Connect to power supply
Single color LED strip +
Output (DC male): Connect to LED strip
Y
Y
E1-M(L)
Dupont Male Connector 2P Spacing 2.54mm 2OAWG The text line is “positive.” The black line is “negative.”
Dupont Female Connector 2P Spacing 2.54mm The black line is “negative.”
2OAWG The text line is “positive.”
AC100-240V Power Supply 5-24VDC
Constant Voltage
Length: 50 cm
Length: 50 cm
Y
Single color LED strip +
Y
Y
Page 1-2
Set Key and Indicator Function
When the light is on, the indicator is brighter; when the light is off, the indicator is less bright. The factory default light off delay time is 30s and the sensing distance is 3m. Please change the light off delay time and sensing distance according to the actual installation requirements by short press or long press the set keywith the equipped pin.
Set the light off delay time: Short press the set key to switch 5 levels of light off delay time in sequence. When the light off delay time is set to 10s, the LED indicator blinks 1 time; When the light off delay time is set to 30s, the LED indicator blinks 2 times; When the light off delay time is set to 60s, the LED indicator blinks 3 times; When the light off delay time is set to 180s, the LED indicator blinks 4 times; When the light off delay time is set to 300s, the LED indicator blinks 5 times;
Note: When the sensor switch is powered up, the LED indicator will blink the corresponding number of times according to the current off delay time setting value.
Set key
LED indicator Sensor face
Set the sensor distance: Long press the set key for 5-20s to set 4 levels of sensing distance in sequence. Long press for 5s, set the sensor distance to 5m, the LED indicator blinks 1 time; Long press for 10s, set the sensor distance to 3m, the LED indicator blinks 2 times; Long press for 15s, set the sensor distance to 1m, the LED indicator blinks 3 times; Long press for 20s, set the sensor distance to 0.5m, the LED indicator blinks 4 times; Note: When long press, the LED indicator is off and will blink the corresponding number
of times at 5s, 10s, 15s, and 20s moments.
Memory function: After power failure and turn on again, the device automatically restores the setting parameters before power failure.
Sensor Switch Installation
Open installation:
Stick the back of the sensor switch to the board with 3M adhesive, and attach the indicator sticker to the front. Concealed installation:
Installation Precautions: 1.Please use 3M adhesive to install the sensor switch anywhere or on the back of non-metallic materials
such as wood, plastic, glass, acrylic, etc. 2.The sensor switch is not affected by ambient temperature, humidity, light, etc., and has strong anti-interference capability. 3.The senor head should be installed in the correct direction and angle.
When installing on the wall, it is recommended to install horizontally with a height of about 1.2-1.8m; When installing on the ceiling, it is recommended to install vertically with a height of about 3m. 4. When installing multiple sensor switches, try to keep each sensor switch placed parallel to each other. 5.When installing, try to avoid facing large metal equipment or pipes to avoid signal interference. 6.Ensure that the sensor switch is not near or obstructed by high density materials (e.g., metal, concrete walls, etc.). These materials can degrade or block the microwave signal and cause false triggering.
Sensor Switch Application
Individual switch application
Multiple switch application
It is recommended to set the delayed light off time of the sensor switch to 30s or 60s. Realize that the light on when people come, and the light off when people leave.
Staircase lighting application
Down direction sensor
For multiple switch applications, it is recommended to set the delayed light off time of all sensor switches to 10s. Realize sequential switching control of multiple lights in the direction of human movement. The installation distance between two sensor switches should be at least 5m to avoid mutual interference.
E1-M(D)
Motion Sensing Switch
Uin= lin=
5-24VDC 3.5A
Uout= Iout=
5-24VDC 3A
Pout= 15W@5V
36W@12V
Temp
72W@24V Range: -20~+55
Stick the front side of the sensor switch to the back of the board with 3M adhesive, and attach the indicator sticker at the corresponding position on the front side of the board. The sensing signal can penetrate about 50mm of wood boards and non-metallic materials, and there is no attenuation at a sensing distance of 0.5 to 5 meters.
User Manual Ver 1.0.0 2025.6
Up direction sensor
For staircase installation application, it is recommended to install two sensor switches on the upper and lower sides of the staircase respectively. And set the delay off time of the sensor switch to 30s or 60s to realize the up/down staircase light on/off control.
Page 3-4
Documents / Resources
 |
iSkyDance E1-M-D Paste Anywhere Human Motion Sensor Switch [pdf] Owner's Manual E1-M-D, E1-M-D Paste Anywhere Human Motion Sensor Switch, Paste Anywhere Human Motion Sensor Switch, Anywhere Human Motion Sensor Switch, Human Motion Sensor Switch, Motion Sensor Switch |