isinwheel D2 D2plus Scoter User Manual

D2/ D2plus EU

User Manual

IMPORTANT! Read carefully and keep for future reference.
Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

WARNING!
Before folding or any servicing, power off the scooter first!
Fully spin the knob to ensure riding safety.

Package Contents

	D2plus
Scooter	Seat
Charger	Hex Wrench
	User Manual & Safety Instructions

Product Overview

1. Screen
2. Control Pad
3. Brake Levers
4. Throttle
5. Hook
6. Height Adjustment Clamp
7. Folding Mechanism
8. Headlight
9. Tyre
10. Indicators (Two Sides)
11. Kickstand
12. Underbody Light (Two Sides)
13. Charging Port
14. Disc Brakes (Front & Rear)
15. Footrest
16. 2-in-1 Taillight & Brake Light

Scooter Assembly

Pull down the kickstand, lift the stem to the riding position, align the U shaped hardware with the holes on the folding mechanism, and turn the knob clockwise to lock the stem in place.

Remove all four bolts of the handlebar clamp faceplate and then the faceplate, place the handlebar into the clamp and the faceplate over the handlebar, and tighten the four bolts.

Scooter Folding

Power off the scooter, turn the knob counterclockwise to fully detach the U-shaped locking hardware from the folding mechanism, and fold down the stem. Then, adjust the hook on the stem so that it catches the footrest.

D2plus Seat Installation and Folding

1) Flip down the seat until it clicks into place.
2) Press and hold the locking pin on the mounting plate, then stand the seat bracket upright until the slot on the locking pin locks in place.
3) Align the holes on the mounting plate with those on the deck, then tighten all the mounting bolts.
4) Open the lever of the seatpost clamp, adjust the seat to the desired height, and fully tighten the clamp. Then close the quick-release lever of the locking pin as shown.

Folding

Basic Operations

1. Indicator switch

Power ON/OFF:
Press and hold the Power button for 2 seconds.
Headlight ON/OFF:
Press the Headlight button to turn on/off the headlight, taillight, and deck lights simultaneously.
Select Riding Mode:
Press the “S” button.
Select TRIP/ODO:
Press the “S” button twice.
Imperial/Metric Units:
Press the “M” button.
Left/Right Indicator:
Press the corresponding button on the indicator switch.

Note:
The scooter will automatically power off after 10 minutes of inactivity.

Display

1. Left Indicator
2. Real-time Speed
3. Headlight on
4. Brake Applied
5. Scooter Locked
6. Right Indicator
7. Motor Overheating Alarm
8. App Connected
9. Riding Mode
10. TRIP: Trip Distance
    ODO: Total Distance
11. Cruise Control
12. Battery Level

Riding Mode	Max Speed
	6 km/h
	10 km/h
	15 km/h
	25 km/h

Settings

There are 3 setting items in the settings.
P1: Start Mode (P10 for zero start and P11 for non-zero start)
P2: Cruise Control (P20 for off and P21 for on)
P4: Odometer resetting

1. To enter the settings, press and hold the Power and Horn buttons simultaneously.
2. Press the Horn button to cycle through P1, P2, and P4.
   • When selecting P1 or P2, press the “M” button to select P10 or P20; press the “S” button to select P11 or P21;
   • When selecting P4, press and hold “M” button to reset the odometer, i.e., total distance.
3. Press the Horn button to switch to the next setting item (changed setting items will be saved).
4. Press the Power and Horn buttons simultaneously or wait 5 seconds to save all the changes and return to the home screen.

About Charging

The scooter is fully charged when the charger indicator changes from red to green.
With charging protection, the scooter will cut off charging automatically after a full charge. We still don’t recommend overcharging it.
Keep the charging port cover closed when not charging.
During charging, the scooter can not be turned on.

Error Code

The following are common error codes you may encounter. If you experience any of these or other error codes, contact us for support.

Specifications

* About the range: Measured under the condition of an 100% battery level, a load of 70 kg (154 Ibs), and a speed of 15 km/h (9 mph). The range will differ depending on different factors, such as load, humidity, wind speed, and operation habits.
* The structure of this scooter is designed to support a maximum load of 120 kg (264 Ibs). For the best riding experience, 70% of the maximum load is recommended.

CE Warning
1) The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
2) Children being supervised not to play with the appliance.

Disposal of Electrical and Electronic Equipment
The crossed-out garbage can means that you are legally obliged to dispose of these devices separately from unsorted municipal waste. Disposal via the residual waste bin or the yellow bin is prohibited. If the products contain batteries or rechargeable batteries that are not permanently installed, they must be removed before disposal and disposed of separately as a battery.

Options for Returning Old Devices (EAR)
Owners of old devices can hand them over within the scope of the options for returning or collecting old devices that have been set up and made available by public waste disposal authorities, so that proper disposal of the old devices is ensured.

Declaration of Conformity
For the full text of the EU Declaration of Conformity, visit the link:
https://www.isinwheel.de/pages/konformitatserklarung