Mounting Instruction for DP3 Power Module
AN6046

Inngangur

This application note describes general concepts, guidelines, and recommendations for the procedures and specifications related to heatsink installation, Printed Circuit Board (PCB) mounting, and  unmounting for the Microchip Dual Pack 3 (DP3) power module. This document does not address all possible applications or conditions that may be encountered by end users.
This document is not part of any warranty agreement from the supplier. We strongly recommends that users perform comprehensive electromechanical evaluations to ensure suitability for their specific application.

DP3 Power Module Overview
The DP3 power module features press-fit pin technology, enabling solderless PCB mounting via a press-fit insertion process. This ensures low-resistance, stable electrical contact. The press-fit pins are tin-electroplated T2 copper with a nominal width of 1.2 mm.
Note: During installation, the press-fit pin is forcibly inserted into the PCB hole. This action deforms the pin, resulting in a tight interference fit and reliable electrical contact between the interfaces.
The following figures show the press-fit pin description and insertion.
Figure 1. Press-fit Pin Description
Figure 2. Press-fit Pin Insertion
Meðhöndlun rafstöðueiginleika (ESD).
Always observe Electrostatic Discharge (ESD) safety precautions when handling ESD-sensitive components, such as IGBT modules. Ensure proper installation and maintain workplace ESD safety compliance to prevent latent or severe damage that may result from excessive static electricity discharge during handling.
The following figure shows the ESD caution symbol.
Figure 3. ESD Caution Symbol

PCB Mounting and Dismounting Instructions

This section describes the detailed information on PCB requirements, as well as instructions for mounting and dismounting the PCB.

1.1. PCB Requirements
The recommended PCB specifications for the DP3 power module with press-fit pins, as provided in this section, are based on experimental validation using standard FR4 material with copper base metallization and tin-plated holes, in accordance with IEC 60352-5. If alternative technologies, design parameters, materials, or metallization thicknesses are considered, end users are advised to perform appropriate qualification and evaluation to ensure compatibility For optimal electrical contact between the press-fit pins and PCB holes, the PCB should be designed according to the specifications as given in the below figure and table. Deviation from these recommendations may result in reduced contact reliability or mechanical issues during PCB mounting.
Figure 1-1. Recommended PCB Design Structure
Tafla 1-1. Recommended PCB Design Specifications

PCB Feature	Min.	Týp.	Hámark	Eining
Þvermál borhola	1.12	1.15	—	mm
Koparþykkt í holu	25	—	50	µm
Hole tin metalization	4	—	15	µm
Loka þvermál holu	0.94	—	1.09	mm
Koparþykkt leiðara	35	70–105	400	µm

1.2. PCB Mounting Process
The DP3 power module is mounted onto the PCB by inserting the module’s press-fit pins into the designated PCB holes. This connection is established through a press-fit process, which can be performed using either a manual lever press or an automated press machine. Automated presses should provide adjustable speed, displacement, and force control to ensure consistent contact quality and repeatability.
The following figure shows the recommended stacking arrangement, including a sample work holder and press plate tool, for the PCB press-fit pin insertion process. Ensure that all interfaces are vertically aligned and parallel to prevent damage or issues such as bent pins, tilted PCBs, or loose connections during mounting.

Mynd 1-2. Recommended Stacking Arrangement
Maintain a minimum clearance of 5 mm from the center of each press-fit pin to adjacent components on the PCB. This spacing must also be considered when designing user-developed press tools and when positioning components on the PCB.
After aligning the PCB and module in the work holder, apply a constant force and speed to insert the pins into the PCB holes. Continue pressing until the PCB contacts the mounting guide or footing on the module. Always verify the planarity between the PCB and the module.
Eftirfarandi mynd sýnir fyrrvample of press-fit insertion process.
Mynd 1-3. Example of Press-fit Insertion Process
The following table lists the recommended press-fit pin insertion parameters. These parameters ensure sufficient force and displacement speed to establish reliable contact between interfaces, based on the specified materials and structure, without damaging the PCB. If alternative parameters, materials, or structures are used, end users should perform their own evaluations.

Tafla 1-2. Recommended Press-fit Pin Insertion Parameters

Parameter	Min.	Týp.	Hámark	Eining
Þvermál borhola		1.15		mm
Press-fit pin insertion speed		25		mm/mín
Copper thicknesss in hole	25	—	50	µm
Press-fit pin insertion force per pin	—	110	—	N

1.3. PCB Dismounting Process
If the PCB needs to be replaced, dismounting can be performed on processed units. A dismounted PCB can be reused and remounted onto the module up to three times. However, a module that has been dismounted should not be reused with the press-fit method, as the pins may be deformed after the initial mounting. If remounting the PCB onto the module is required, soldering the pins to the new board is necessary to ensure a reliable and stable connection.
The dismounting process can be performed using a manual lever press or a mechanized press machine. The upper press-out tool, developed by the end user, must be designed according to the PCB layout to apply pressure only to the press-fit pins and avoid damaging other components.
To dismount, place the module with the mounted PCB onto the work holder, ensuring the board is fully supported by the tooling ledge. Apply force to the pins to release the contact between interfaces and separate the module from the PCB. The module will descend into the work holder, and the PCB will be completely detached.
The following figure shows the dismounting process using a sample work holder and press plate tooling.
Mynd 1-4. Example of Press-fit Extraction Process
The following table lists the recommended press-fit pin extraction parameters.
Tafla 1-3. Recommended Press-fit Pin Extraction Parameters

Parameter	Min.	Týp.	Hámark	Eining
Extraction speed		12		mm/mín
Press-fit pin extraction force per pin	40	—	—	N

Fastening the PCB to the Module

Additional fasteners are used to secure the PCB to the module. These fasteners help maintain connection integrity by minimizing tension between the PCB and the press-fit pins. Using additional fasteners also reduces the risk of external strain affecting the pins during subsequent processes.

2.1. Fastener Recommendations
The DP3 power module includes a PCB footing and screw guide structure with an internal hole diameter of 2.1 ± 0.1 mm. This design supports the use of self-tapping screws with a recommended diameter of 2.25 mm to 2.45 mm. Select a screw length between 4 mm and 10 mm, based on the thickness of the PCB and the weight of the mounted assembly.
The following figures shows the mounting hole dimension, recommended screw dimension, and the PCB footing structure respectively.
Mynd 2-1. Stærð festingarhols
Mynd 2-2. Mælt er með skrúfumáli
Mynd 2-3. PCB Footing/Screw Guide Location
2.2. Fastening Screw Insertion
The upper part of the screw holes is designed to guide and support the PCB during mounting. This area cannot withstand excessive forces during self-tapping screw insertion. Always ensure vertical alignment of the screw to the hole and use the correct screw diameter. Misalignment or incorrect screw size can cause damage to the module and negatively impact the quality of the press-fit pin and PCB contact.
The recommended mounting torque is approximately 0.4–0.5 Nm. Manual screw tightening is preferred to minimize the risk of damage. If automated tools are used, select electronically controlled drivers with slow rotation speed. End users should assess and validate the chosen method to ensure safe and reliable installation.
The following figures show the properly aligned mounting screw, misaligned mounting screw, and possible mechanical damage due to misaligned screw or incorrect screw diameter.
Mynd 2-4. Properly Aligned Mounting Screw
Mynd 2-5. Misaligned Mounting Screw
Mynd 2-6. Possible Mechanical Damage

Heatsink Mounting Assembly

Temperature regulation is essential to ensure optimal functionality of power modules, particularly during high-power switching operations, which can generate significant heat due to power loss. To maintain the module within its allowable operating temperature range, use a heatsink to dissipate excess heat.

3.1. Heatsink Requirements
The condition of the materials at the heatsink-to-baseplate interface is critical during mounting, as it directly affects heat dissipation. Ensure that all contact surfaces are free from contamination, foreign materials, and corrosion. The mounting surface of the heatsink should have a surface roughness of less than 10 μm and a flatness of less than 30 μm.
Verify that the heatsink is rigid and can withstand subsequent processes without twisting or distortion. Defects in the heatsink can increase contact thermal resistance and introduce additional stress to the module, potentially leading to thermal or electrical failure.

3.2. Thermal Conductive Paste (TCP) Application
Applying TCP during mounting fills gaps between the baseplate and the heatsink, which are caused by surface irregularities. Proper application of TCP significantly improves heat dissipation efficiency and reduces the thermal resistance of the module during operation.
To achieve optimal thermal dissipation and ensure uniform and reproducible thermal layers, apply TCP using a stencil screen printing process. This method allows for precise control and adjustment of TCP distribution for each module. The recommended thermal paste thickness is typically between 50 μm and 100 μm.
The following figure shows the stencil screen printing process. In this process, the unit is placed on a work holder, the stencil screen is positioned on top of the module, and TCP is applied using a manual metal squeegee.
Mynd 3-1. Stencil Screen Printing Process
3.3. Mounting Screw and Tightening Requirement
The DP3 power module requires four DIN M5 screws for heatsink mounting. When selecting screws and washers, ensure that the resulting clearance and creepage distances between the power terminals and the nearest screw head or washer comply with applicable standards. Evaluate these distances during the development phase.
Follow the below steps for heatsink mounting procedure and bolt tightening sequence:

1. Position the Module
   a. Place the power module, with thermal conductive paste applied, onto the heatsink.
2. Initial Screw Placement
   a. Insert all four M5 screws.
   b. Tighten each screw to 0.5 Nm in the following diagonal sequence: 1 – 2 – 3 – 4, see Figure 3-2.
3. Intermediate Tightening
   a. Tighten each screw to 2 Nm, following the same sequence: 1 – 2 – 3 – 4.
4. Lokaaðhald
   a. Tighten each screw to the specified final torque, again in the sequence: 1 – 2 – 3 – 4.
   b. See the product datasheet for the maximum allowable torque.
5. Torque Verification (Recommended)
   a. Use a torque-controlled screwdriver for all tightening steps.
   b. If possible, re-tighten all screws to the final torque in the same sequence (1 – 2 – 3 – 4) after three hours.

The following figure shows the tightening sequence to mount the module to the heatsink.
Mynd 3-2. Tightening Sequence to Mount the Module to the Heatsink

Connection Pull and Push Forces for DP3 Module

The DP3 power module must be mounted to ensure that pull forces applied to the power terminals are minimized. Excessive pull or push forces can damage the terminals or compromise the reliability of the electrical connection.
The following figure shows the maximum allowable pull and push forces at the power terminals during the screw-in operation.
Mynd 4-1. Maximum Pull and Push Forces for DP3 Module

Assembling Busbars to Power Terminals

Mount the busbars onto the power module and secure them to the power terminals using M6 screws with M6 flat washers. Select the screw length based on the combined thickness of the busbar and washers. Ensure that the effective thread engagement does not exceed a maximum depth of 10 mm in the module. See product datasheet for the maximum allowable torque.
To minimize switching over voltages, place decoupling capacitors as close as possible to the VBUS and 0/VBUS power terminals.
When installing isolated spacers, set their height (X) to be approximately 0.5 mm lower than the height (Y) of the power terminals. This pre-tensions the power terminals and prevents permanent force in the Fz+ direction (see Figure 4-1 and Figure 5-1). Ensure that the busbars are at the same height as the power connectors. See the following figure and the product datasheet for an example af réttri samsetningu.
For heavy components such as electrolytic or polypropylene capacitors located near the power module, use isolated spacers to support their weight. The weight of these components should be borne by the spacers, not by the power module. Add additional isolated spacers as needed to prevent issues caused by vibration and shock.
Mynd 5-1. Example of DP3 Assembly

Niðurstaða

This application note provides key recommendations for mounting the DP3 power module.
Following these guidelines will help minimize mechanical stress on the busbar, PCB, and power module, supporting long-term system operation. Adhering to the specified heatsink mounting instructions is also critical to achieving the lowest possible thermal resistance from the power chips to the cooler. Implementing these procedures is essential to ensure optimal system reliability.

Endurskoðunarsaga

Endurskoðunarferillinn lýsir þeim breytingum sem voru innleiddar í skjalinu. Breytingarnar eru taldar upp eftir endurskoðun, frá og með nýjustu útgáfunni.

Endurskoðun	Dagsetning	Lýsing
A	07/2025	Upphafleg endurskoðun

Örflöguupplýsingar

Vörumerki
„Microchip“ nafnið og lógóið, „M“ merkið og önnur nöfn, lógó og vörumerki eru skráð og óskráð vörumerki Microchip Technology Incorporated eða hlutdeildarfélaga þess og/eða dótturfélaga í Bandaríkjunum og/eða öðrum löndum („Microchip“ Vörumerki“). Upplýsingar um Microchip vörumerki er að finna á https://www.microchip.com/en-us/about/legalinformation/microchip-trademarks.
ISBN: 979-8-3371-1627-3

Lagatilkynning
Þetta rit og upplýsingarnar hér má aðeins nota með Microchip vörur, þar á meðal til að hanna, prófa og samþætta Microchip vörur með forritinu þínu. Notkun þessara upplýsinga á annan hátt brýtur í bága við þessa skilmála. Upplýsingar um tækjaforrit eru aðeins veittar þér til þæginda og uppfærslur kunna að koma í stað þeirra. Það er á þína ábyrgð að tryggja að umsókn þín uppfylli forskriftir þínar. Hafðu samband við staðbundna söluskrifstofu Microchip til að fá frekari aðstoð eða fáðu frekari aðstoð á www.microchip.com/en-us/support/design-help/client-support-services.
ÞESSAR UPPLÝSINGAR ER LAÐAR AF MICROCHIP „Eins og þær eru“. FYRIR MICROCHIP GERIR ENGIN STAÐSETNING EÐA ÁBYRGÐ HVORKI sem er skýlaus eða óbein, skrifleg eða munnleg, lögbundin eða á annan hátt, sem tengist upplýsingunum, þ.mt EN EKKI TAKMARKAÐ VIÐ EINHVER ÓBEINU ÁBYRGÐ, ÁBYRGÐARÁBYRGÐ, ÁBYRGÐARÁBYRGÐ, ÁBYRGÐARÁBYRGÐ TENGST ÁSTAND ÞESS, GÆÐUM EÐA AFKOMU. MICROCHIP VERÐUR Í ENGUM TILKYNNINGUM ÁBYRGÐ Á NEIGU ÓBEINU, SÉRSTÖKUM, REFSINGU, TILVALUSTU EÐA AFLEITATAPI, Tjóni, KOSTNAÐI EÐA KOSTNAÐI af einhverju tagi sem tengist UPPLÝSINGUM EÐA NOTKUN ÞEIRRA, HVER SEM AFRIÐI AF ÞVÍ. MÖGULEIKUR EÐA Tjónið er fyrirsjáanlegt. AÐ FULLSTA MÁL LÖGUM LEYFIÐ VERÐUR HEILDARÁBYRGÐ MICROCHIP Á ALLAR KRÖFUR Á EINHVER HÁTT TENGST UPPLÝSINGARNIR EÐA NOTKUN ÞESSAR EKKI ÚR SEM ÞAÐ SEM ÞÚ HEFUR GREIÐIÐ BEINLEGT FYRIR UPPLÝSINGARNUM.
Notkun örflögutækja í lífsbjörgunar- og/eða öryggisforritum er algjörlega á ábyrgð kaupanda og kaupandinn samþykkir að verja, skaða og halda örflögu skaðlausum fyrir hvers kyns tjóni, kröfum, málsókn eða kostnaði sem hlýst af slíkri notkun. Engin leyfi eru send, óbeint eða á annan hátt, undir neinum Microchip hugverkaréttindum nema annað sé tekið fram.

Örflögutæki Kóðaverndareiginleiki 
Athugaðu eftirfarandi upplýsingar um kóðaverndareiginleikann á Microchip vörum:

• Örflöguvörur uppfylla forskriftirnar í tilteknu örflögugagnablaði þeirra.
• Microchip telur að vöruflokkur þess sé öruggur þegar þær eru notaðar á tilsettan hátt, innan rekstrarforskrifta og við venjulegar aðstæður.
• Örflögu metur og verndar hugverkaréttindi sín ákaft. Tilraunir til að brjóta kóða verndareiginleika Microchip vara eru stranglega bannaðar og geta brotið gegn Digital Millennium Copyright Act.
• Hvorki Microchip né nokkur annar hálfleiðaraframleiðandi getur ábyrgst öryggi kóðans. Kóðavernd þýðir ekki að við tryggjum að varan sé „óbrjótanleg“. Kóðavernd er í stöðugri þróun. Microchip hefur skuldbundið sig til að bæta stöðugt kóðaverndareiginleika vara okkar.

Umsóknarathugið
© 2025 Microchip Technology Inc. og dótturfélög þess
DS00006046A – 16

Skjöl / auðlindir

MICROCHIP AN6046 DP3 Power Module [pdfLeiðbeiningarhandbók AN6046 DP3 Power Module, AN6046, DP3 Power Module, Power Module, Module

Heimildir

• Notendahandbók