MF-LINKFINITYKIT2
Efni
Tæknilýsing
120x120x25mm / 177g
DC12V – 0.25A / DC5V – 0.75A
MARSGAMING
Biomag SL
ESB skrifstofa:
Heimilisfang: Barratxi 39, Pab. 3
01013, Vitoria, SPÁNI
Sími: +34945124598
Netfang: attcliente@biomag.es
Framleitt í Kína
Ráðleggingar og öryggisáminningar
Keep children away from the equipment parts while installing the product.
Protect your hands and fingers when handling and installing the product.
Disconnect the computer from the power source before installation.
Turn off and unplug the computer before cleaning the fan.
Use compressed air to remove accumulated dust from the blades and frame.
Avoid direct contact with the fan blades while it is operating.
Keep the computer in a clean and dry environment, away from heat sources, dust, and moisture, as these can limit the lifespan of the fans.
DO NOT open the product casing; the unit operates with dangerous voltages.
EKKI breyta snúrunum eða tengjunum sem fylgja með þessari vöru.
EKKI nota snúru millistykki eða snúrur sem fylgja ekki með.
DO NOT apply excessive force when plugging in and unplugging connectors.
Important notice: If you notice any damage or irregularity in the product, please do not proceed with the installation and contact our customer service immediately. Failure to follow these instructions could result in risks of injury or additional damage.
Uppsetning
- Choose the location in the computer case where you want to install the fans and place the front of the fan towards the outside of the case if you want to bring in cool air, or towards the inside if your goal is to exhaust warm air.
A. Installing 3 fans together Use 2x 5-pin to 5-pin join pieces to connect the 3 fans together.
B. Installing 2 fans together + 1 fan separately: Use lx 5-pin to 5-pin union connector to connect 2 fans together and use the extension cable to connect the separate fan to the other 2 fans. - Screw the fans to the case using the included screws.
- Connect the 5-pin adapter cable to the fan.
- Connect the PWM connector to a “FAN” port on the motherboard.
- Connect the 3-pin ARGB connector via the SATA adapter (5.1) or directly to a motherboard or ARGB controller to control the lighting (5.2).
[5] Lighting
5.1 Automatic lighting mode: The fans will light up with an automatic rainbow lighting effect. Use this mode if an ARGB motherboard is not available.
- Connect the ARGB cable to the SATA adapter.
- Connect the SATA adapter connector to a SATA connector on the power supply.
5.2 ARGB lighting mode (Optional): The fan lighting can be controlled with a compatible ARGB motherboard using the ARGB cable.
- Connect the ARGB cable to the +5V 3-pin connector on the motherboard.
- Ensure that the motherboard is compatible with 3-pin +5V ARGB lighting. Make sure the ARGB connector from the fans is connected to the correct ARGB control device port; otherwise, components could be damaged. If you have doubts about the compatibility of your motherboard or controller with ARGB lighting, feel free to contact us for assistance.
- ASUS AURA, Mystic Light Sync, RGB Fusion & ARGB controllers
Úrræðaleit
– Fan not spinning: Check the connections and make sure they are properly installed.
– Excessive noise: Make sure there is no obstruction to the fan. The fan can be noisy if the speed is too high, adjust the fan speed curves in the BIOS or control software to reduce the fan speed (RPM) without compromising cooling. If the fan has been exposed to dust or dirt it may have deteriorated, contact us for assistance.
– Fans not lighting up: Make sure the fans are connected as shown in the connection diagram. If the fans’ 5V 3-pin ARGB connector has been connected to a motherboard or controller, make sure they are compatible with ARGB devices.
Ábyrgð
The original purchase receipt will be required to use the warranty service. Please keep it in a safe place. Opening the device, manipulations, technical modifications of any kind, and damages caused by external mechanical forces will void your warranty. To read the terms and conditions of the warranty, visit es.marsgaming.eu/es/terms
Fylgni
Þú getur skoðað samræmisyfirlýsingu Evrópusambandsins fyrir þessa vöru á www.marsgaming.eu/en/conformity. Fyrir frekari upplýsingar, heimsækja www.marsgaming.eu
Förgun og endurvinnsla
At the end of the product’s life, it must not be disposed of with regular household waste. To promote environmental sustainability and ensure proper waste management, please take the product to a designated collection and recycling center.
Hafðu samband
If you have questions or issues with the product, do not hesitate to contact us: attcliente@biomag.es / +34945124598
Skjöl / auðlindir
 |
MARS GAMING MF-LINKFINITYKIT2 viftubúnaður [pdfLeiðbeiningarhandbók MF-LINKFINITYKIT2 viftusett, MF-LINKFINITYKIT2, viftusett, sett |