irocks K71R Rechargeable Wireless Mechanical Keyboard Installation Guide

Press FN+Ctrl+S to enable or disable Energy Saving Mode. When the mode is enabled, backlight of your keyboard will automatically be turned off after 5 minutes of keyboard inactivity and turned back on after pressing any key. Energy Saving Mode in wired mode is disabled by default.

Wireless Installation:

1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on your computer
3. Turn on the power of keyboard and make sure battery has enough power
4. Your computer will automatically detect the receiver and connect with the keyboard
※To set idle timeout for keyboard’s Energy Saving Mode in RF mode

：Fully disable Energy Saving Mode (Key 0 will blink 3 times when enabled)
：1.5 minutes (default value, Key 1 will blink 3 times when enabled)
：5 minutes (Key 2 will blink 3 times when enabled)
：10 minutes (Key 3 will blink 3 times when enabled)

Product Information

LED indication

: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red) Blinking : Low Power Static : Charging Off : Fully Charged

PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function will be turned off automatically. The keyboard could be used for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for charging time saving.

Hotkeys

Press “ “ and desired function key simultaneously to use hotkeys.

Setting key function

：N-Key Rollover anti-ghosting function ( default )

：6-Key Rollover anti-ghosting & standard USB settings
：Factory reset ( Press and hold for 5 seconds )

Backlight Function Keys

Side Backlight

:Select side backlight colors ( depending on backlight effects )

:Adjust side backlight speed ( depending on backlight effects )
:Turn side backlight on or off

:Switch between side backlight effects ( 7 types )

Keyboard Backlight

：Adjust brightness ( 4 levels )
: Select or switch key backlight colors ( depending on backlight effects )

：Adjust backlight speed ( depending on backlight effects )
：Turn keyboard backlight on or off
：Light fadeout and tracing effects ( 5 types )
：Monochrome and breathing backlight effects
：Backlight Customization Mode

Onboard memory can store up to five backlight customization profile. Users may set backlight according to their preferences, and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively after saving.

How to customize backlight:

A. Press“ ：or (2/3/4/5) to select and switch to lighting mode 1 ( 2/3/4/5)
B. Press“ ：simultaneously to activate custom backlight setting ( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light up; press to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for the key
F. After configuration, press“ to save all
settings to current lighting mode and leave backlight customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode

：RGB Backlight Effects – Set A ( 3 options )
：RGB Backlight Effects – Set B ( 7 options )

Multimedia & function key

：Show Desktop
：Lock PC
：Search for files or folders
：Launch Calculator
：Open my Computer
：Open E-Mail
：Open the internet browser

：Media player
：Play / pause
：Backward

：Stop play
：Forward
：Full key lock ( keyboard only lights up Esc key when mode is in effect )

：Turn Windows lock on or off

Smart wheel function

Smart wheel is powered by Windows 10 protocol without additional software, if you’re using the latest version of Windows 10.
Smart Wheel is customizable and will automatically switch to your preferred tool depending on software you’re using. Switch between scrolling, zoom, rotation, brush tuning, video editing, multimedia control and more. Smart Wheel support ranges from Windows 10 built-in apps to pro software.

Press the below button to switch wheel mode

：Wheel – volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
：Wheel – Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
：Wheel – Smart Wheel
Only works on PC with Windows 10 Go to Windows 10 Settings -> Devices -> Wheel for customization

Software

The keyboard software is working under wired mode only; however, saved keyboard settings will be applied under both wired and wireless mode. Please go to I Rocks official website to download and install latest software for backlight, macro, multimedia keys configuration and more.

Double click the installation software you download and follow the instructions step by

Plug in the keyboard after installation, the software will start to identify i
Launch the software. It will take some time to download the memory parameter and setting of the keyboard

Attention: Connection switch (on the bottom of your keyboard ) must be flipped to ” W ” to use the software

Troubleshooting & Cautions

If your wireless keyboard does not work normally:

Check if connection switch on the bottom of your keyboard is flipped to ” R ” (2.4G wireless mode)
Check the USB receiver is connected to your computer’s USB port correctly – unplug and plug it back.

Charge your keyboard immediately when the battery low indicator lights up.
Metal objects close to or in between the keyboard may reduce wireless performance. Try moving metal objects away from the keyboard.
For saving power, the keyboard goes into sleep mode when it’s not in use for a while. Press any key and wait for 1 to 3 seconds to bring the keyboard out of sleep mode.

Charge the battery of your keyboard before storing it without use. Storing your keyboard with low battery status and voltage for long periods of time may cause battery malfunction.
When your keyboard is not in use, switching to USB wired mode (connection switch W) is recommended.
Avoid putting your keyboard under high moisture condition or direct sun.

Do not expose your keyboard to extreme temperatures, heat, fire or liquid.

Wireless ID Pairing

The wireless keyboard is pre-paired with included receiver before shipment. It saves the need to pair and is ready to use out of the box. When you need to re-pair your keyboard and receiver manually to prevent signal interference or other issues, please follow the steps below:

Flip the connection switch to ” R ” for 2.4G wireless mode and make sure the keyboard is powered on.

Press and hold Fn + P for 3 seconds to enter pairing mode. (P Key will flash)
Unplug and plug the USB receiver back into your computer’s USB port.
Move the keyboard to close the USB receiver within 15cm, the ID setting process will start automatically. (It will take about 4~8 seconds)

Your keyboard should be ready to use
The above steps need to be completed within 1 minute, If the keyboard doesn’t work properly, please remove the USB receiver from computer’s USB port, then proceed to step 2~4 again.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example – use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.

Customer Support

Rocks Technology Co., Ltd.
Headquarter Office
7F., No. 786, Zhongzheng Rd., Zhonghe Dist.,
New Taipei City 23586, Taiwan
Tel : +886-2-2225-5080
Fax : +886-2-2228-1712
www.i-rocks.com
i-Rocks Korea
www.i-rocks.co.kr
i-Rocks Malaysia
57-A, Jalan SS21/1A, Damansara Utama, 47400,
Petaling Jaya, Selangor, Malaysia
Tel : +603-77339233
www.i-rocks.com

Documents / Resources

irocks K71R Rechargeable Wireless Mechanical Keyboard [pdf] Installation Guide
IRK71R, UJ9IRK71R, DG011, K71R Rechargeable Wireless Mechanical Keyboard, K71R, Rechargeable Wireless Mechanical Keyboard, Wireless Mechanical Keyboard, Mechanical Keyboard, Keyboard

References

User Manual

Package Contents

Hardware Installation

Wired Installation: