Intelix SKYPLAY-DFS-S Wireless HDMI Distribution System

Important Safety Instructions

• Follow all warnings and instructions marked on the device.
• This product is for indoor use only.
• Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.
• Do not use the device near water.
• Do not place the device near, or over, radiators or heat registers.
• The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.
• The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.
• Never spill liquid of any kind on the device.
• Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Clean only with a dry cloth.
• The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
• To prevent damage to your installation it is important that all devices are properly grounded.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Use only accessories specified or recommended by Intelix.
• Explanation of graphical symbols:
• Lightning bolt/flash symbol: the lightning bolt/flash and arrowhead within an equilateral triangle symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product enclosure which may be of sufficient magnitude to constitute a risk of shock to a person or persons.
• Exclamation point symbol: the exclamation point within an equilateral triangle symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
• Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over. If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
• To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
• Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.
• Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
• If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.
• The power cord or plug has become damaged or frayed.
• Liquid has been spilled into the device.
• The device has been exposed to rain or water.
• The device has been dropped, or the cabinet has been damaged.
• The device exhibits a distinct change in performance, indicating a need for service.
• The device does not operate normally when the operating instructions are followed.
•  Only adjust those controls that are covered in the operating instructions. Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
• Use only with the cart, stand, table, or rack specified by Intelix or sold with the equipment. When/if a cart is used, use caution when moving the cart/equipment combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.

Product Overview

The SKYPLAY-DFS distributes HDMI high-definition audio and video up to 30 meters (100 feet) in both point-topoint, point-to-many, and many-to-point configurations. Each transmitter is compatible with up to 4 receivers and each receiver can be paired to switch up to 4 transmitters. The SKYPLAY-DFS-S can transmit 1080p video with stereo or multichannel audio. The SKY PLAY-DFS-R can transmit IR signals from the remote location to control the source device. The SKYPLAY-DFS transmitter and receiver must be paired together to pass video. Amimon Pro transmission and AES 128-bit encrypted processing ensure the integrity of digital signals and real-time processing (less than one frame), whether transmitting in open spaces or through light construction, such as framed drywall walls. The SKY PLAY-DFS radios are configured for US and Canada operation. The SKY PLAY-DFS-EU radios are configured for Europe and Australian operation. The instructions in this manual will make references to SKYPLAY-DFS, which also applies to SKY PLAY-DFS-EU.

Connections

SKY PLAY-DFS-S Features and Connections

Top

Front

Right

SKY PLAY-DFS-R Features and Connections

Rear TopFront

IR Remote

The included IR remote performs all of the pairing and source selection operations of the SKYPLAY-DFS wireless HD distribution system.

Enter the menu
Return to the previous menu
Select video source
Up, down, left, right for menu
Confirm selection
Remove video source
Add video source
Power off the receiver
Select source 1
Select source 2
Select source 3

Installation Instructions

Quick Start

• Wall mount the transmitter (optional)
• Wall mount the receiver (optional)
• Connect source and control to transmitter
• Connect display to receiver
• Point-to-point pairing
• Point-to-many pairing (signal distribution)
• Many-to-point pairing (signal switching

Wall Mount the Transmitter

• In addition to resting on a flat surface, the SKYPLAY-DFS-S can be mounted on a wall or furniture
• The mounting holes on the SKYPLAY-DFS-S are vertically oriented with 620 mm (2.44 in) separation.
• Use #10 pan head screws that are long enough to secure the transmitter to the wall while also providing a 6 mm (0.24 in) space to reach the mounting holes.

Wall Mount the Receiver

In addition to resting on a flat surface, the SKYPLAY-DFS-R can be mounted on a wall or furniture

• The mounting holes on the SKYPLAY-DFS-R are horizontally oriented with 475 mm (1.87 in) separation.
• Use #8 pan head screws that are long enough to secure the transmitter to the wall while also providing a 8 mm (0.31 in) space to reach the mounting holes.

Connection

Connect Source and Control to Transmitter

• Connect an HDMI cable between the HDMI port on the source device to be extended and the HDMI Input port on the SKYPLAY-DFS-S.
• Plug the IR emitter into the IR Out port on the SKYPLAY-DFS-S.
• Remove the adhesive on the IR emitter. Attach the emitter to the IR window on the source device.
• Plug the power supply into a wall outlet. Do not apply power to the SKYPLAY-DFS transmitter at this time

Connect Display to Receiver

• Place the SKYPLAY-DFS-R in a location where the IR Receiver is not blocked by any obstructions.
• Connect an HDMI cable between the HDMI Out port on the SKYPLAY-DFS-R and the HDMI Input port on the display.
• Plug the power supply into a wall outlet. Do not apply power to the SKYPLAY-DFS receiver at this time.

Point-to-Point Pairing

Without remote

• Apply power to the display.
• Plug the power supply with USB connector into the Power Input port on the SKYPLAY-DFS-R.
• Plug the power supply into the Power Input port on the SKYPLAY-DFS-S.
• Apply power to the source device.
• Press and hold the Register button on the SKYPLAY-DFS-R until the following message appears on the display:
• Please Activate Registration on Transmitter Unit
• Press and hold the Register button on the SKYPLAY-DFS-S until the following message appears on the display:
• Adding transmitter name. Press OK to continue or Exit to cancel
• Press the Register button on the SKYPLAY-DFS-R to confirm.
• The following message with a progress bar will appear on the display while the devices are paired:
• Adding transmitter name…
• When pairing is complete, the message and progress bar will be removed from the display

With remote

• Apply power to the display.
• Plug the power supply with USB connector into the Power Input port on the SKYPLAY-DFS-R.
• Plug the power supply into the Power Input port on the SKYPLAY-DFS-S.
• Apply power to the source device.
• Press the Exit button to cancel searching for a SKYPLAY-DFS-S.
• Press the OK button to enter the Setup menu.
• Press the OK button to initialize the pairing process.
• Press and hold the Register button on the SKYPLAY-DFS-S.
• Once an active SKYPLAY-DFS-S is found, press OK on the remote to start the pairing process.
• The display will show the progress of the pairing status with the SKYPLAY-DFS-S.
• Once pairing is complete, a brief message will show the SKYPLAY-DFS-S is paired with the SKYPLAY-DFS-R before starting to transmit video.

Point-to-Many Pairing (Signal Distribution)

• Power off all paired SKYPLAY-DFS receivers.
• Repeat the process for point-to-point pairing.
• Apply power to all receivers after pairing is complete on all units.

Many-to-Point Pairing (Signal Switching)

• Power off all paired SKYPLAY-DFS transmitters.
• Apply power to the unpaired SKYPLAY-DFS-S.
• Select And New Video Source from the Setup menu.
• Repeat the process for point-to-point pairing.
• Apply power to all transmitters after pairing is complete on all units.
• Use the remote control to switch between available transmitters.

Additional SKYPLAY-DFS-R Menu Options

Pressing the Menu button on the remote will go back to the previous menu. Pressing the Exit button will close the menu and return to playing back the video stream

Rename a Transmitter

The SKYPLAY-DFS-R provides an option to modify the name of the transmitter. This is merely an alias for the specific SKYPLAY-DFS-R being used

• From the Setup menu, arrow down to Modify Video Source Name and press the OK key on the remote control
• Select the source to rename, then press the OK key.
• Use the left and right arrow keys on the remote control to select a letter to change. Use the up and down arrow keys to cycle through the available characters.
• Once the name has been changed, press the OK key

Remove a Transmitter
The SKYPLAY-DFS-R provides an option to remove a paired SKYPLAY-DFS-S from the available list of transmitters.

• • From the Setup menu, arrow down to Remove Video Source and
  • Setup press the OK key on the remote control
  • Select the SKYPLAY-DFS-S to be removed and press the OK button.
  • A confirmation message will verify the specify SKYPLAY-DFS-S to be removed. Press the OK button to remove the transmitter.

Disconnect Wireless Link

The SKYPLAY-DFS-R Disconnect Wireless Link option is available to remove the link between the current receiver and the transmitter to allow another receiver to accept the video stream.

LED States

Link LED

Video LED

Power LED

Troubleshooting

Pairing Fails

• Make sure both transmitter and receiver are powered on.
• Make sure pairing units are the only SKYPLAY devices currently powered on.
• Bring the transmitter and receiver closer together but no closer than 1 meter.
• Keep the number of solid walls between the transmitter and receiver to a minimum.

No Signal on the Display

• Make sure the receiver is powered on.
• Make sure the monitor is powered on.
• Make sure the receiver is properly connected to the display.
• Make sure the display is set to display video from the right source (HDMI1, HDMI2 etc.).
• Reboot the receiver.
• Unplug and then re-plug the HDMI cable between the receiver and the display.
• Replace the HDMI cable.
• Make sure the video resolution is supported by the display.

No Video over the Wireless Link

• Make sure the transmitter is properly connected to the source.
• Make sure the network LED is powered on.
• Make sure the source is powered on.
• Unplug and then re-plug the transmitter to the source.

Abnormal Color or Noise on the Display

• Unplug and then re-plug the HDMI cable between the receiver and the display.
• Unplug and then re-plug the HDMI cable between the transmitter and the source.
• Bring the transmitter and receiver closer together but no closer than 1 meter.
• Keep the number of solid walls between the transmitter and receiver to a minimum.
• Power cycle the SKYPLAY-DFS.

No Audio

• Check the mute and audio volume settings on the display.
• Verify the audio format setting on the source is compatible with the SKYPLAY-DFS.

Other Issues

• The receiver keeps outputting a “Searching…” message, and the NETWORK LED constantly blinks
• It should take up to one minute to establish a wireless link. If the link was not established within that time period, verify the transmitter is powered on and not connected to another receiver.
• The receiver is outputting “Connected to source name, Please Check Video Source”
• Check the HDMI connection between the transmitter and the video source.
• The receiver displayed a connection failure message and outputs a “Wireless Off” message
• If there is more than one registered transmitter, and the receiver failed to connect to it within a minute or two, the receiver will go into standby mode and shut down the wireless radios. In order to connect to the desired source, pressthe Source button on the IR remote and choose the desired source.
• The Link LED blinks rapidly and there is no video on the display
• Power cycle the SKYPLAY-DFS-R. If the issue remains, the device might be faulty. Please contact Liberty AV Solutions technical support.
• Link cannot be established or poor video/audio quality
• Try to decrease the range between the transmitter and the receiver or remove obstacles out of the way between the transmitter and receiver

Technical Specifications

SKYPLAY-DFS 

SKYPLAY-DFS-EU 

FCC

This module in its final integration requires the end-product to continue to comply with DFS requirements. A class II permissive change may be required for operation not already described in the FCC Grant filing.  The OEM of final integrator must ensure that FCC labeling requirements are met for a host using this module, if (1) the module’s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module should be used, with the following contents: Contains TX FCC ID: VSQAMNKHIN1. RX FCC ID: YG7ZRF32200  The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. The applicable usage is to be used as a wireless device, connected to the back of a professional camera and transmitting live video, coming from BNC connectors.  Only the supplied approved antenna should be used.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation

Thank you for your purchase.
Please contact us with your questions and comments.

• Intelix
• 8001 Terrace Ave, Ste 201
• Middleton, WI 53562
• Phone: 608-831-0880
• Toll Free: 866-462-8649
• Fax: 608-831-1833
• www.intelix.com
• supportlibav@libav.com

FAQS

How many SKYPLAY-DFS-Rs can be connected to one transmitter?
The transmitter will broadcast to four SKYPLAY-DFS-Rs. If a fifth receiver is to replace a currently active SKYPLAY-DFS-R, the active receiver must disconnect the wireless link or power off before the video stream will pass to the new receiver.

How many SKYPLAY-DFS-Ss can be operational in an installation?
In a theoretical installation that has no outside interference, up to ten transmitters can function. Realistically, up to four transmitters can operate well.

How close can one SKYPLAY-DFS-S be to another?
In order for the transmitted radio signal to reach the line of sight maximum distance of 100 meters, transmitters should be positioned at least 2 meters from each other.

How does DFS affect the SKYPLAY-DFS?
When the SKYPLAY-DFS products are first powered on, they will pair on one of the non-DFS channels to establish communication. After 60 seconds, the SKYPLAY-DFS will start scanning the DFS channels to see which one is available for use. Once a channel is selected for use, the SKYPLAY-DFS will continue to scan the DFS channels for a backup channel in case a higher priority signal takes over the first DFS channel. In the event no non-DFS channels are available, the SKYPLAY-DFS will not play any video and the following message will appear on the display: Please wait 60 sec, system acquiring DFS frequency. After 60 seconds, the SKYPLAY-DFS will establish a link on the “best” DFS channel found. If all non-DFS and DFS channels are occupied, the following message will appear: Connection Failed. The SKYPLAY-DFS will have to be linked at a later time

References

• User Manual