Intel 82574L 1G Gigabit Desktop PCI-e Network Adapter User Manual
Description
This PCIe Gigabit Network card is single, compact, low power components that offer a fully-integrated Gigabit Ethernet Media Access Control and physical layer port. It is used of Intel high-performance chip NH82574L,and it is uses the PCI Express architecture and provides a single-Port implementation in a relatively small area so it can be used for server and any other personal computers.
Specification
- Fully compliant with PCI-Express Base Specification Revision1.1
- Single-Lane(x1)PCI-Express with throughput up to 2.5Gbps
- Fully Plug and Play compatible
- Full-duplex operation at 10/100/1000Mb/s
- Half-duplex operation at 10/100Mb/s
- 10/100/1000 data rate auto negotiation operation
- Fully compliant with IEEE802.3,802.3u,802.3ab
- Support full duplex flow control(IEEE802.3x)
- Supports IEEE802.1P Layer 2 Priority Encoding
- Supports IEEE802.1Q VLAN tagging
- IPv4 and IPv6 checksum offload support
- Receive Side Scaling(RSS) with two hardware receive queues
- Supports jumbo frame to 9k bytes
- Crossover detection and Auto correction operation
Package content
- 1 x PCIe Intel 82574L Gigabit network adapter
- 1 x User’s Manual
- 1 x CD
- 1 x Low profile bracket
System Requirements
- FreeBSD, Linux, VMware ESXi,XP,Vista,8,8.1,and 10 32/64bit
- Windows server 2003/Server2008 R2/Server2012 R2
- One available PCIe x1/x4/x8/x16 slot
Cabling Requirements:
Intel 1 Gigabit adapters
- For 1000BASE-T or 100BASE-TX.use Category 5 or Category5e wiring, twisted 4-pair copper:
- Make sure you use Category 5 cabling that complies with the TIA-568 wiring specification For more information on this specification.
- Length is 100 meters max.
- Category 3 wiring supports only 10Mbps
CAUTION: If using less than 4-pair cabling, you must manually configure the speed and duplex setting of the adapter and the link partner. In addition,with2-and3-pair cabling the adapter can only achieve speeds of up to 100Mbps
- For 100BASE-TX.use Category 5 wiring.
- For10BASE-T.use Category 3 or 5wiring
Hardware installation
- Turn off the computer and unplug the power cord
- Remove the computer cover and the adapter slot cover from the slot that matches your adapter
- Insert the adapter edge connector into the slot and secure the bracket to the chassis
- Replace the computer cover ,then plug in the power cord
- Power on the computer
Install Drivers
Windows○, R Operating Systems
You must have administrative rights to the operating system to install the drivers.
- insert the CD driver bound with Intel network driver into your CD-ROM drive(also you can download the latest drivers from):
- if the Found New Hardware Wizard screen is displayed, click Cancel
- start the autorun located in the software package, the autorun may automatically start after you have extracted files.
- Click install Drivers and Software
- Follow the instructions in the install wizard to finish it.
Installing Linux Drivers from Source Code
- Download and expand the base driver tar file.
- Compile the driver module.
- Install the module using the modprobe command.
- Assign an IP address using the ifconfig command.
Support
More information and settings, please refer to the Adapter User Guides or you can contact us.
Documents / Resources
 |
Intel 82574L 1G Gigabit Desktop PCI-e Network Adapter [pdf] User Manual 82574L 1G Gigabit Desktop PCI-e Network Adapter, 82574L, 1G Gigabit Desktop PCI-e Network Adapter, Desktop PCI-e Network Adapter, PCI-e Network Adapter, Network Adapter, Adapter |
