inno IMX708 Camera Module
Description
Overview
- CAM-IMX708AF Camera Module Feature with Sony IMX708 Sensor, Autofocus lens, IR-filter, Compatible with Raspberry Pi Camera Module 3 Standard Version.
- CAM-IMX708AF can be used to take full HD video as well as stills photographs and feature an HDR mode up to 3 megapixels. It carries IR cut filter. Its operation is fully supported by the libcamera library, including Camera Module 3’s rapid autofocus feature: this makes it easy for beginners to use, while offering plenty for advanced users. Camera Module 3 is compatible with all Raspberry Pi computers.
- CAM-IMX708AF Camera Module Third Generation: Back-illuminated and stacked CMOS 12-megapixel image sensor (IMX708) with HDR for up to 3-megapixel output
- High-quality Image Output: 4608 × 2592 pixels, carrying IR cut filter, along with built-in 2D DPC and QBC Re-mosaic function, offering high SNR
- Autofocus System: Phase detection autofocuses
- CSI-2 serial Data Output: 2-wire serial communication, supporting I2C fast mode and fast-mode plus
Features
- Back-illuminated, stacked CMOS 12-megapixel IMX708 image sensor
- High signal-to-noise ratio (SNR), built-in 2D dynamic defect pixel correction (DPC)
- Phase detection autofocus (PDAF) for rapid autofocus
- Diagonal field of view: 75 degrees, common video modes: 1080p50, 720p100, 480p120, output RAW10
- Supports Raspberry PI5, PI4, PI3
SPECIFICATION
| Sensor | Sony IMX708 |
| Resolution | 11.9 megapixels |
| Sensor size | 7.4mm sensor diagonal |
| Pixel size | 1.4μm × 1.4μm |
| Common video modes | 1080p50, 720p100, 480p120 |
| Output | RAW10 |
| IR filter | Yes |
| Autofocus system | Phase Detection Autofocus |
| Dimensions | 32x32mm(12.4mm height for Wide variants) |
| Ribbon cable length | 150mm |
| Cable connector |
|
Hardware
Camera Size 
Camera Module Pins Out
 |
||||
| Pin # | Name | Description | ||
| 1 | GND | Ground | ||
| 2 | CAM_D0_N | MIPI Data Lane 0 Negative | ||
| 3 | CAM_D0_P | MIPI Data Lane 0 Positive | ||
| 4 | GND | Ground | ||
| 5 | CAM_D1_N | MIPI Data Lane 1 Negative | ||
| 6 | CAM_D1_P | MIPI Data Lane 1 Positive | ||
| 7 | GND | Ground | ||
| 8 | CAM_CK_N | MIPI Clock Lane Negative | ||
| 9 | CAM_CK_P | MIPI Clock Lane Positive | ||
| 10 | GND | Ground | ||
| 11 | CAM_IO0 | Power Enable | ||
| 12 | CAM_IO1 | LED Indicator | ||
| 13 | CAM_SCL | I2C SCL | ||
| 14 | CAM_SDA | I2C SDA | ||
| 15 | CAM_3V3 | 3.3V Power Input |
Autofocus Lens Information
| Focus range | 10cm–∞ |
| Focal length | 4.74mm |
| Diagonal f ield of view | 75 degrees |
| Horizontal f ield of view | 66 degrees |
| Vertical f ield of view | 41 degrees |
| Focal ratio (F-stop) | F1.8 |
| IR-Filter | Yes |
Connection 
Software
Modify config.txt
- sudo nano /boot/config.txt
- For the latest version raspberry Pi OS, it should be
- sudo nano /boot/firmware/config.txt
Add the content below to the last line
- dtoverlay=imx708
- Change to
- camera_auto_detect=1
- to
- camera_auto_detect=0
Reboot and use below command to preview
libcamera-hello -t 0
Documentation
- Camera Description on Raspberry Pi
- Camera Software On Raspberry Pi
CONTACT US
- Support: support@inno-maker.com
- Bulk Price: sales@inno-maker.com
- Wiki: wiki.inno-maker.com
- Github: https://github.com/INNO-MAKER
| Date | Revision | Change Details |
| 2024/09/08 | V1.0 | First Released |
Frequently Asked Questions
Is the CAM-IMX708AF Camera Module compatible with all Raspberry Pi models?
Yes, the camera module is compatible with Raspberry Pi 5, Pi4, and Pi 3 models.
What autofocus system does the camera module use?
The camera module uses Phase Detection Autofocus (PDAF) for rapid focusing.
Documents / Resources
 | IMX708 Camera Module |
References
- github.com/INNO-MAKERgithub.com
- Maker by Yahoomaker.com
- Welcome to Astro.wiki.inno-maker.com
- INNOMAKER| Automotive Ethernet|USB CAN|USB CAMERA|HIFI AUDIO – INNOMAKER|SOM|SBC|OEM|DESIGN|FABRICATIONwww.inno-maker.com
- User Manualmanual.tools
Published: November 26, 2025