IMPACT KEYGRIP Adjustable Offset Arms

Precautions
- Please read and follow these instructions and keep this manual in a safe place.
- Make sure that this product is intact and that there are no missing parts.
- Do not exceed the light stand’s maximum load capacity.
- Always use sandbags when using this product.
- Make sure all connections are secure before proceeding.
- Always add a safety cable for underslung lights.
- All images are for illustrative purposes only.
Specifications
| Item | Connections | Points of Articulation | Construction Material | Length (closed) | Weight | Length (max) | Dimensions (H x D) |
| Adjustable Arm | 5/8 in. baby pin, 1 1/8 in. junior pin, 5/8 in. baby receiver | None | Steel | 19.25 in. (48.9 cm) | 4 lb. (1.8 kg) | – | 6.75 x 2.25 in. |
| Adjustable Offset Arm | 1 1/8 in. junior receiver, 1 1/8 in. junior pin | – | – | – | 5.6 lb. (2.5 kg) | – | 6.75 x 15 in. |
Overview
SA-OADH-BJ Adjustable Baby Offset Arm
- Baby pi
- Telescoping arm section
- Knob storage tap hole
- Locking knob
- Baby receiver / Junior pin
- Length adjustment locking knob
SA-JOA-A Adjustable Junior Offset Arm
- Telescoping arm section
- Junior receiver
- Locking knob
- Junior pin
- Length adjustment locking knob
Setting UP the Offset Arms
Before you start
- Using a C-stand
- Make sure the C-stand’s top leg Is taclng thesame dlrectlon as the offset arm.
- Using a standard Light Stand
- Make sure the light stand’s legs are fully extended, and the struts are parallel to the floor. Point one ot the light stand’s legs racing in the same direction as the offset arm.
Important! Before you mount light fixtures onto the arm. Make sure the legs ot the C-stand or light stand are sandbagged.
Mounting the Offset Arm
Mounting the SA-OADH-BJ onto a Baby Pin
- Mounting the Offset Arm
- Mounting the SA-OADH-BJ onto a Baby Pin
- Position the offset arm and tighten thelocking knob until secure.
Mounting the SA-OADH-BJ onto a Junior Receiver
- Unscrew the receiver locking knob. The baby receiver becomes a junior pin.

- For safekeeping, screw the locking knob into the tap hole until you need it again.

- Place the offset arm’s junior pin into the combo stand or light stand’s junior receiver and tighten the locking knob until secure.

Mounting the SA-JOA-A
- Place the offset arm’s junior pin into the combo stand’s junior receiver and tighten the locking knob until secure.
Mounting a Light Fixture to the Arm
SA-OADH-BJ
- Loosen the locking knob of the light fixture’s yoke. Make sure the lock is completely loosened so the offset arm’s baby pin will fit entirely into the receiver.

- Aim the light and tighten the locking knob until secure.

SA-JOA-A
- Loosen the offset arm’s junior receiver locking knob.

- Fully insert the light fixture’s junior pin into the offset arm’s receiver and tighten the locking knob until secure.

Adjusting the Arm Length
- Loosen the locking handle on the offset arm and extend or retract the arm to the desired length.
- Tighten the locking handle until secure.
Important! Always hold onto the rig when extending the arms, and ensure the load’s stability and balance before letting go. Always place the arm in line with one of the legs and counterbalance with sandbags on the legs opposite the load.
One-Year Limited Warranty
This KEYGRIP by Impact product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.
- This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation, or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY
EXPRESS WARRANTIES OR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state. - To obtain warranty coverage, contact the Impact Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Impact along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.
- For more information or to arrange service, visit www.impactstudiolighting.com or call Customer Service at 212-594-2353.
- Product warranty provided by the Gradus Group.
- www.gradusgroup.com
- KeyGrip and Impact are registered trademarks of the Gradus Group.
- 2026 Gradus Group LLC. All Rights Reserved.

Documents / Resources
![]() | KEYGRIP Adjustable Offset Arms |
References
- gradusgroup.comwww.gradusgroup.com
- impactstudiolighting.comwww.impactstudiolighting.com
- User Manualmanual.tools
