iGear Apollo Bluetooth Party Speaker
PACKAGE CONTENTS
- Bluetooth Speaker
- TYPE- A to C Charging Cable
- Aux Cable
- Warranty Card
- User Guide
SPECIFICATIONS
- Bluetooth Version: 5.3
- Chipset: JL
- Range: Up to 10 m
- Profiles: A2DP HFP, HSP, AVRCP
- Driver: 2 x low
- Impedance: 4Ω
- Frequency Response: 90 Hz – 20 kHz
- Signal to Noise Ratio: 80 dB
- Total Power Output: 20W
- Charge Input: DC 5V, 1 A
- Battery Capacity: 3000 mAh
- Charge Time :6 Hours
- Playback Time: 3 – 5 Hours
- Max Size for USB Input: 64
- Max Size for SD Input: 64 GB
IDENTIFYING PARTS
Power On / Power Off / RGB Light
Volume Up / Next Track Button
Volume Down / Previous Track Button
Mode Switch / TWS Connection
Play / Pause
CHARGING
- Please fully charge the Bluetooth speaker before using it for the first time.
- The red indicator light will be lit while the speaker is charging.
- When the battery is full, the red indicator light will switch off automatically.
- Avoid charging the speaker for more than 8 hours.
BLUETOOTH PAIRING
Your speaker must be paired to a Bluetooth device before it can be used. It is only necessary to pair your speaker once with each device.
- Press the power on button. The LED light will flash blue and a welcome tone will be heard.
- Press the M Button to switch to Bluetooth mode. The speaker will beep, indicating it’s ready to pair with your Bluetooth playback device.
Pairing a second speaker:
- Both speakers need to be paired with each other before connecting to your Bluetooth device.
- When both speakers are in Bluetooth mode, press the Button on one of the speakers to pair them together. You’ll hear a connection tone once both speakers are paired.
This pairing only needs to be done once.
Connecting to your Bluetooth device:
- Activate Bluetooth on your playback device and search for “iGear Apollo”. Select “iGear Apollo” from the device list to connect. You’ll hear a connection tone after successful pairing.
- You can now play audio through the speaker.
- Music tracks can be selected either on the speaker or your playback device (smartphone, computer, tablet, etc.). Press the A Button to skip to the next song, or the V Button to play the previous song.
- Volume can be controlled either on the speaker or your playback device. Press and hold the A Button or the V Button to adjust the volume.
- Press the Button on the speaker to play or pause the music.
CONTROLS
Function Operation
| Function | Operation |
| Increase Volume | Press the ∧ Button once |
| Decrease Volume | Press the ∨ Button once |
| Switch to Next Track | Long press the ∧ Button |
| Switch to Previous Track | Long press the ∨ Button |
| Play or Pause Track | Press the >| Button once |
| Navigate between the USB, SD, FM Radio, Bluetooth and Aux modes | Short press the M Button |
| RGB Light | Short press the RGB Light Button |
| TWS Connection | Double press the M Button |
Bluetooth and USB Mode
| Function | Operation |
| Increase Volume | Press the ∧ Button once |
| Decrease Volume | Press the ∨ Button once |
| Switch to Next Track | Long press the ∧ Button |
| Switch to Previous Track | Long press the ∨ Button |
| Play or Pause Track | Press the >| Button once |
Note: None of these buttons will work in AUX Input mode, except for the volume buttons.
FM RADIO
| Function | Operation |
| Increase Volume | Press the ∧ Button once |
| Decrease Volume | Press the ∨ Button once |
| Navigate up through saved channels |
Long press the ∧ Button |
| Navigate down through saved channels |
Long press the ∨ Button |
| Automatic Station Scan | Press the >| Button once |
PLAYING MP3’S FROM A USB FLASH DRIVE OR SD CARD
- Power on.
- Insert USB flash disk into the slot. The music stored will be played automatically.
- Press the A button on the speaker to skip to the next song, or the V button to play the previous song.
- Press the button on the speaker to play or pause the music.
- Press and hold the A button or the V button to adjust the volume.
Note; In Bluetooth mode, inserting a USB flash drive will disconnect Bluetooth and switch to playing from the USB flash drive. Press the M Button to switch back to Bluetooth mode.
ALIX-IN
- Plug the provided audio cable into the compatible device’s Aux input and then into the Aux input of the speaker.
- Press and hold the A button or the V button to adjust the volume.
FM Radio
- Once the device is turned on, press the M Button to cycle to FM radio mode.
- Long press the button to search for all available FM channels and store them automatically
- To switch between radio stations, press the A button or the V button to select radio stations.
Note: Insert the AUX cable into the speaker to receive good signal reception. Inserting the AUX cable while the speaker in FM mode will cause the speaker to automatically switch to Aux mode. Pressing the M button again will cycle back to FM mode.
LOCATING THE BLUETOOTH MENU
For iPhone, iPad, and iPod Touch:
- Go to Settings on your device.
- Select Bluetooth. If Bluetooth is off, switch it on.
- Your iPhone/iPad/iPod will automatically search for new devices.
For Android Phones and Tablets:
- Go to the Settings Menu on your device.
- Choose Bluetooth (on older Android devices, Bluetooth is located in the Wireless & Networks menu).
If Bluetooth is off, toggle it on. - Select “Search for devices” if your phone or tablet does not automatically search for new devices.
CAUTION: Do not remove panel covers by unscrewing them.
To reduce the risk of electric shock, do not remove the cover. No user-serviceable parts inside. Refer servicing to a qualified service personnel only.
WARRANTY
- Warranty period: 1 Year
- In case of consumer complaints:
- Customer Care – +91 9372667193
- Email: support@igear.asia
(Between IOam to 5pm, Mon-Fri) - www.igearworld.com
For Warranty Scan the OR Code
Documents / Resources
 |
iGear Apollo Bluetooth Party Speaker [pdf] User Guide Apollo Bluetooth Party Speaker, Apollo, Bluetooth Party Speaker, Party Speaker |