Ntuziaka Modular Ngosipụta elekere nke onye nwe

ọdịnaya zoo

1 Ngosipụta elekere Modular ihe nkuzi

2 Elekere ngosi modular

3 Akwụkwọ / akụrụngwa

3.1 Ntụaka

4 Ozi ndị metụtara

Ngosipụta elekere Modular ihe nkuzi

Elekere ngosi modular

nke Gammawave
Ihe oru ngo a na-eji ihe ngosi ihe ngosi Modular gara aga mee elekere dijitalụ, na-eji anọ nke modul jikọtara ọnụ ma na-achịkwa Microbit na RTC.

Ngwunye:
Microbit V2 (nke a họọrọ n'ihi na-ekwu okwu arụnyere, V1 ga-arụ ọrụ mana ọ ga-achọ ụda mpụga.)

DS3231 RTC
Gbanwee SPST

Kitronik Edge Njikọ Breakout
Jumper Jerky Junior F/M – Qty 20

Jumper Jerky Junior F/F – Qty 4
Jumper Jerky F/F – Qty 3

Jumper Jerky F/M – Qty 3
470R resistor

1000uF capacitor
Isi akụkụ aka nri 2 x (ụzọ 3 x 1 ahịrị) chọrọ.

WS2812 Neopixel bọtịnụ LED's * 56qty.
Waya ọla kọpa enamelled 21 AWG (0.75mm dia.), Ma ọ bụ waya mkpuchi mkpuchi ọzọ.

Mpempe akwụkwọ
kposara M2

M2 kposara 8mm - Qty 12
M2 kposara 6mm - Qty 16

M2 Bolts 10mm - Qty 2
M2 mkpụrụ - nkeji 2

M2 washers - Qty 2
M2 Hex oghere 5mm - Qty 2

Bolt M3
M3 washers - Qty 14

M3 bolts 10mm - Qty 2
M3 bolts 25mm - Qty 4

M3 mkpụrụ - nkeji 12
Hex kwụ ọtọ M3

M3 Hex oghere 5mm - Qty 2
M3 Hex oghere 10mm - Qty 4
Aka nri akụkụ aka nri (15(W) x 40(L) x 40(H) mm) - Qty 2
Nwere ike gosipụta ọnụ ahịa dị oke ọnụ iji zụta ụkpụrụ dị iche iche karịa ụkpụrụ onye ọ bụla, ọ gwụla ma ị nwere ha. Akụkụ ụfọdụ nwekwara ike ịnwe MOL karịa ọnụọgụ akọwapụtara na ndepụta akụrụngwa.
Ihe nbipute 3D
Filament ọcha - Maka ngosipụta ngosi kachasị.
Black Filament - Maka bọọdụ nkwado.
2mm igbapu bit
3mm igbapu bit
5mm akụrụngwa akụrụngwa
Kwuo egwu
hụrụ
Pliers
Ndị na-egbutu waya
Ígwè na-ere ere
Onye na-ere ahịa
Akwụkwọ mpempe akwụkwọ

Screwdrivers
Mara ngwá ọrụ gị ma soro usoro arụ ọrụ akwadoro ma jide n'aka na ị ga-eyi PPE kwesịrị ekwesị.
Enweghị njikọ na ndị na-ebubata ngwaahịa a na-eji na ọrụ a, nweere onwe gị iji ndị na-ebubata gị masịrị ma dochie ihe ndị dabara na mmasị nke gị ma ọ bụ isiokwu ịnye.

Njikọ dị irè n'oge mbipụta.
Nzọụkwụ 1: Baseplate Strips
Lee: Ihe ngosi Modular (MDE)

A na-achọ ihe anọ "Ngosipụta Modular" iji mepụta elekere elekere ma na-ejikọta ihe ndị a na eriri baseplate nke e wepụrụ site na nnukwu ala.
Iberibe baseplate ahụ tụrụ 32 (W) x 144(L) mm ma ọ bụ 4 x 18 stubs na nke ọ bụla n'elu laps abụọ MDE na-ejikọta na stubs na MDE. Agbanyeghị, maka ike agbakwunyere, a na-etinye skru anọ M2 x 8mm nso n'akụkụ akụkụ ndị na-agafe na baseplate wee banye na MDE.
Nzọụkwụ 2: Atụmatụ

Nhazi ahụ na-egosi ihe ndị eji ejikwa MDE nke nwere 56 Neopixels.
Ihe njikwa ahụ nwere Microbit, RTC, Breakout Board, Switch na sekit nchebe.
Ọtụtụ n'ime ihe ndị a na-ere ahịa na-elekwasị anya na Neopixels ebe a na-ejikọta akụkụ njikwa ya na jumpers.

Nzọụkwụ 3: Koodu
Emebere koodu na MakeCode.
"oonn ssttaarrtt" pproocceedduurree..

Na-amalite eriri Neoplxel nke 56 LED
Gosipụta ozi aha.
Na-ebido ngalaba_list nke nwere aha ngalaba maka nọmba a ga-egosipụta. Nọmba 0 echekwara na mmewere [0] = 0111111

Nọmba 1 echekwara na mmewere [1] = 0000110
Nọmba 9 echekwara na mmewere [9] = 1101111
Na mgbakwunye.

Ọnụọgụ 10 echekwara na mmewere [10] = 0000000 ejiri mee oghere maka nkeji.

usoro mgbe nile

Oku 'set mode' nke na-elele P1 ma ọ bụrụ na elu na-enye ohere ịtọ oge ma ọ bụghị na-egosiputa oge dị ugbu a.

Ọ na-akpọ 'Time_split' nke na-ejikọta ụkpụrụ ọnụọgụ abụọ nke awa na nkeji n'ime eriri agwa 4, tupu oge xing nọmba ọ bụla na-erughị 10 nwere efu efu.
Oku 'pixel_time'
Nke na-ewepụta mkpụrụedemede anọ nke ọ bụla n'aka malite na agwa ikpeazụ n'ime segment_value
Ọnụọgụ ahụ nwere uru dị na ngalaba_list nke akụkụ_value zoro aka na ya.

(Ọ bụrụ akụkụ_value = 0 wee ọnụọgụ = mmewere [0] = 0111111)
Inc = index x (LED_SEG) x 7). Ebe ndeksi = nke n'ime mkpụrụedemede 4 ka edere, LED_SEG = ọnụọgụ LED's kwa akụkụ, 7 = ọnụ ọgụgụ nke akụkụ na nkeji.
Ụdị a bụ mmalite nke LED ka a ga-achịkwa maka àgwà kwesịrị ekwesị.

Ihe maka mmewere na-ekenye n'aka nke ọ bụla nọmba na nkeji na uru.
Ọ bụrụ uru =1 mgbe ahụ pikselụ ekenyere inc ka atọrọ ka ọ na-acha uhie uhie wee gbanye ma ọ bụghị ya, ọ ga-atụgharị o.
Dị ka LED abụọ n'otu akụkụ chọrọ usoro a ugboro ugboro LED_SEG ugboro.

(Ọmụmaatụ Ọ bụrụ na nkeji nkeji bụ 9, index = 0, digit = 1011111 [uru = 1, inc = 0 & inc = 1], [uru = 0, inc = 2 & inc = 3] .... [uru = 1, inc = 12 & inc = 13])
Oge elekere iri [Index = 1, inc nso 14 ruo 27], nkeji nkeji [index = 2, inc range 28 ruo 41], nkeji iri [index = 3, inc range 42 ruo 55].
Ozugbo emechara ụkpụrụ 7 nke ọ bụla wee ziga ya na warara a ga-egosi mgbanwe ndị ahụ.

Ewebatara igbu oge iji gbochie icker.
na bọtịnụ AA"
Nke a na-ewepụta awa ma ọ bụrụ set_enable = 1

na bọtịnụ BB"
Nke a na-esetịpụ nkeji ma ọ bụrụ set_enable = 1 "ogologo bbuuttttoonn AA ++ BB"
Nke a na-akpọ 'oge setịpụ' nke na-ewepụta oge dabere na ụkpụrụ enyere ya na bọtịnụ A na B.

https://www.instructables.com/F4U/P0K0/L9LD12R3/F4UP0K0L9LD12R3.txt

Kwụpụ 4: Panel azụ
A na-ejikọta ihe ndị ahụ na mpempe akwụkwọ (95(W) x 128(L) mm), nke etinyere na azụ nke MDE na M3 X 25mm bolts na 10mm standos. A na-agbanye oghere anọ site na oghere ndị dị na bọọdụ nkwado Neopixel na ebe a na-eguzobe iji tinye ihe mgbakwasị ụkwụ na nkuku, a na-eme oghere 3mm n'ime oghere ka ọ kwekọọ na bolts. Ọnọdụ na oghere oghere maka njikọ Edge Breakout (2 x 3mm), RTC (2 x 2mm), na mgba ọkụ na-ahụ maka ịhapụ ohere (20 x 40mm), iji bulie akara aka nri nke na-eme dị ka ụkwụ. Njikọ na RTC na-eji 4 Junior jumpers F/F na-echekwa RTC na 2 x M2 bolts. Njikọ na mgba ọkụ na-eji 2 Junior jumpers F/M na-agbanye mgba ọkụ site na oghere 5mm. Njikọ na sekit nchebe CR maka Neopixels na-eji 3 Jumpers F / F na site na nke a na Neopixels na 3 jumpers F / M, nke a na-ejikọta ya na bọọdụ na eriri eriri na-eri nri site na otu oghere dị na bọọdụ ahụ.
Dakọta ụkwụ ihe njide akụkụ n'ala ala ala yana bolts 4. (M3 bolts nke dị n'akụkụ ala maka ijikọta baseplate ahụ nwere ike iji jide ụkwụ n'ebe a na-eji ihe nkedo nke abụọ n'ime oghere dị ala nke bracket. Iji gbochie ịcha elu nke elekere ga-anọdụ ala, tinye osisi na pads ma ọ bụ di na nwunye. Mgbanwe nke teepu nwere ike tinye ugbu a na bolts nkwado nkuku ma chekwaa ya na mkpụrụ.

Nzọụkwụ 5: Arụ ọrụ

A na-enye ike site na ijikọ eriri USB ozugbo na Microbit.
Seetttingg nke a klloockk..
Tupu ịtọọ elekere hụ na RTC nwere batrị agbanyere ka ọ were were oge mgbe/ọ bụrụ na ewepụrụ ike. Usoro oge ndabara bụ ọnọdụ elekere 24.

Bugharịa ngbanwe ahụ gaa n'ọnọdụ oge atọrọ a ga-egosi akara gbakwunyere na ngosi.
Pịa bọtịnụ A maka awa. (0 ruo 23)
Pịa bọtịnụ B maka nkeji. (0 ruo 59)
Pịa bọtịnụ A & B ọnụ iji tọọ oge, a ga-egosipụta ụkpụrụ oge etinyere.

Bugharịa mgba ọkụ site na ọnọdụ atọrọ.
AAtt sswwiittcchh bụ ihe na-eme ka ọ pụta ìhè.

Mgbe obere oge gachara, a ga-emelite ihe ngosi na oge dị ugbu a
Nzọụkwụ 6: N'ikpeazụ
Nchikota nke oru di ntakiri di na nwunye na-ebute nnukwu oru ngo. Na-atụ anya na gị na nke a na ọrụ ndị metụtara nke gara aga nke mmasị.