1. Okwu mmalite
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Juno 2-Inch Flat Trim Canless Wafer LED Downlight. This innovative lighting solution is designed for quick and easy installation in various ceiling spaces, eliminating the need for traditional recessed housings. It features an all-in-one design with switchable white color temperature and adjustable lumen output, offering versatile lighting for accent, task, or general illumination.
Figure 1: Juno 2-Inch Flat Trim Canless Wafer LED Downlight with its remote driver box.
2. Ozi nchekwa
Please read all instructions carefully before installation and retain this manual for future reference. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Always turn off power at the circuit breaker before beginning installation or performing any maintenance.
- All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unfamiliar with proper electrical wiring connections, consult a qualified electrician.
- Agbanwela ma ọ bụ gbanwee ngwaahịa n'ụzọ ọ bụla.
- Gbaa mbọ hụ na ọkọnọ voltage dakọtara na ihe nkwụnye ahụ (120 Volts).
- This product is suitable for wet locations and is IC Rated for direct contact with insulation.
- Do not install damaged products. Inspect the product upon receipt.
3. Ihe ngwugwu
Nyochaa na akụrụngwa niile dị na emebighị emebi tupu ịga n'ihu na ntinye:
- LED Lens (Integrated with Downlight Fixture)
- Mounting Hardware (Spring clips, remote driver box)
Note: The downlight fixture and remote driver box are typically pre-assembled or connected.
4. Atụmatụ
The Juno 2-Inch Flat Trim Canless Wafer LED Downlight offers advanced features for optimal lighting performance and ease of use:
- Nhazi enweghị kandụl: No housing required, allowing installation directly into ceiling drywall.
- Switchable White Color Temperature (SWW5): Easily select from five color temperature options:
- 2700K Soft White
- 3000K ọkụ na-acha ọcha
- 3500K nọpụrụ iche ọcha
- 4000K Cool White
- 5000K Ìhè ụbọchị
- Adjustable Lumen Output (ALO25): Choose from three brightness levels (Low, Medium, High) to suit your needs.
- Enwere ike ibelata: Compatible with most standard TRIAC dimmers, dimming down to 10 percent.
- Ike dị irè: Long-life LEDs and a high-efficiency driver ensure superior illumination and extended service life.
- IC kwadoro: Approved for direct contact with insulation, simplifying installation in insulated ceilings.
- Wet Location Certified: Suitable for use in bathrooms, showers, and outdoor covered areas.
Figure 2: Switches on the remote driver box allow selection of color temperature and lumen output.
Figure 3: Visual guide to the different color temperatures available.
5. Ntọala na nwụnye
The canless design simplifies installation. Follow these steps for a secure and proper setup:
- Gbanyụọ ike: Before starting, ensure the power to the installation area is turned off at the circuit breaker.
- Kwadebe mmeghe: Cut a 2-inch diameter hole in the ceiling drywall at the desired location. Ensure there are no obstructions (joists, pipes, wires) within the ceiling space.
- Jikọọ Wiring:
- Open the remote driver box.
- Connect the building's supply wires (hot, neutral, ground) to the corresponding wires in the driver box using appropriate wire connectors.
- Gbaa mbọ hụ na njikọ niile echekwara na mkpuchi nke ọma.
- Close the driver box cover.
Figure 4: The remote driver box houses the electrical connections and adjustment switches.
- Select Settings (Pre-Installation): Before inserting the downlight into the ceiling, use the switches on the remote driver box to select your desired color temperature (2700K-5000K) and lumen output (Low, Medium, High). These settings can be adjusted later if needed, but it's easier before final installation.
- Insert Driver Box: Place the remote driver box into the ceiling opening. Its slim design allows it to fit into tight spaces.
- Install Downlight:
- Gently push the spring-loaded clips on the sides of the downlight upwards.
- Insert the downlight into the ceiling opening.
- Once the downlight is fully inserted, release the clips. The clips will spring back down and firmly secure the fixture against the ceiling.
Figure 5: Dimensions of the downlight and driver box for installation planning.
- Weghachi ike: Turn the power back on at the circuit breaker. Test the downlight's functionality.
6. Ntuziaka ọrụ
Your Juno LED Downlight is designed for simple operation once installed.
- Gbanyụọ/ Gbanyụọ: Control the light using a standard wall switch connected to the circuit.
- Igha: If connected to a compatible TRIAC dimmer switch, adjust the brightness by manipulating the dimmer control. The light can be dimmed down to 10% of its maximum output.
- Adjusting Color Temperature and Lumen Output:
The color temperature and lumen output are set via switches located on the remote driver box (refer to Figure 2). To change these settings after installation, you will need to access the driver box, which may require temporarily removing the fixture from the ceiling or accessing the box through an attic/access panel if it was placed there. It is recommended to set these preferences during installation.
- Mgbanwe Okpomọkụ Agba: Select from 2700K, 3000K, 3500K, 4000K, or 5000K.
- Lumen Output Switch: Choose Low, Medium, or High brightness.
7. Nlekọta
The Juno LED Downlight requires minimal maintenance due to its durable design and long-life LEDs.
- Nhicha: Hụ na agbanyụrụ ọkụ tupu ị sachaa ya. Jiri ihe dị nro, kpọrọ nkụ, ma ọ bụ obere ihe hichaa ihe nkwụnye ọkụ ahụ.amp Ákwà. Ejila ihe nhicha ma ọ bụ ihe mgbaze, n'ihi na ha nwere ike imebi ihe ndị dị na ya ma ọ bụ ihe ndị dị na eletriki.
- Ogologo ndụ ọkụ: The integrated LEDs are designed for extended operation and do not require replacement under normal use.
8. Nchọpụta nsogbu
If you encounter issues with your downlight, refer to the following common problems and solutions:
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Ìhè anaghị agbanwuo. | Enweghị ikike na ngwa. Njikọ wiwi adịghị agwụ agwụ. Faulty switch or circuit breaker. | Lelee ihe mgbawa sekit na mgba ọkụ mgbidi. Turn off power, check all wire connections in the driver box. Test switch or breaker; replace if necessary. |
| Ọkụ na-enwu ma ọ bụ na-ebelata nke ọma. | Mgbanwe dimmer na-ekwekọghị ekwekọ. Waịkọ rụrụ arụ. Sekit ebufere oke. | Ensure dimmer is TRIAC compatible and designed for LED lighting. Gbanyụọ ike, lelee njikọ waya niile. Reduce load on the circuit or consult an electrician. |
| Okpomọkụ ma ọ bụ ìhè agba na-ezighi ezi. | Switches on driver box set incorrectly. | Access the remote driver box and adjust the color temperature and lumen output switches to desired settings. |
Ọ bụrụ na nsogbu ahụ anọgide mgbe ị nwalechara ngwọta ndị a, kpọtụrụ ndị ọrụ nkwado ndị ahịa.
9. Nkọwapụta
| Njirimara | Nkọwa |
|---|---|
| Ụdị | Juno |
| Aha Nlereanya | WF2 RD ALO25 SWW5 90CRI 120 MW M6 (Round LED) |
| Nha | 2-Inch Flat Trim |
| Agba | Matte White |
| Ihe onwunwe | Aluminom, polycarbonate |
| Ụdị isi iyi ọkụ | Ikanam |
| Voltage | 120 volts |
| Wattage | 9.2 watt |
| Atụmatụ pụrụ iche | Adjustable Color Temperature (2700K-5000K), Dimmable (Triac), Energy Efficient, Waterproof |
| Ụdị nwụnye | Flush Mount (Canless) |
| Ojiji ime ime/n'èzí | Indoor, Outdoor (Wet Location Certified) |
| Akụkụ ngwaahịa | 3.2"L x 3.2"W x 1.3"H (Fixture) |
| Ibu Ibu | 13.2 ounces |
| Asambodo | CSA certified, Title 24, Energy Star, IC Rated |
10. Akwụkwọ ikike na nkwado
Akwụkwọ ikike: This product comes with a Limited Warranty. Please refer to the product packaging or the manufacturer's official website for specific terms and conditions of the warranty.
Nkwado ndị ahịa: For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Juno customer support. Contact information can typically be found on the product packaging or the official Juno websaịtị.
Akụrụngwa dị n'ịntanetị: For additional information, product updates, or FAQs, visit the official Juno websaịtị: www.acuitybrands.com/brands/juno
