Okwu mmalite
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Weiser Prague Matte Black Passage Door Knob. This non-locking knob is designed for interior doors such as those for hallways and closets, where no locking mechanism is required. The sleek matte black finish and contemporary design enhance any home interior.
Kedu ihe dị na Igbe ahụ
- 1 Set of Door Knobs (Interior and Exterior)
- 1 Latch
- 1 Efere Elu
- Ịkwanye kposara
- Akwụkwọ ntuziaka nwụnye
Ngwa achọrọ
- Phillips Head Screwdriver (#2 recommended)
Ntuziaka nwụnye
Follow these steps for proper installation of your Weiser Prague Passage Door Knob. For visual guidance, refer to the product overview vidiyo dị n'okpuru.
Vidiyo: Ngwaahịa gafereview - Demonstrates components and assembly process.
- Prepare Door and Check Dimensions:
Ensure your door meets the following specifications: door thickness 1-3/8" to 1-3/4" (35mm-44mm); Latch Backset 2-3/8" (60mm) or 2-3/4" (70mm); Cross Bore 2-1/8" (54mm). If drilling a new door, use the supplied template and complete door drilling instructions.
Image: Weiser Prague Matte Black Passage Door Knob, front view.
- Adjust the Backset of the Latch (if needed):
Hold the latch in front of the door hole with the latch face flush against the door edge. If the latch holes are centered in the door hole, no adjustment is required. If not centered, adjust the latch by moving the pin to extend the latch.
Image: All components of the door knob laid out, including the latch, knobs, and screws.
- Wụnye Latch:
Insert the latch into the door edge. Secure it with the provided screws. Ensure the slant bolt faces the door frame when the door is closed.
- Wụnye Knobs:
Press the latch bolt to install the exterior knob. Remove the interior knob. Loosen the pre-installed set screw on the interior knob base. Place the knob base on the center point and secure with screws. Push up on the knob base while tightening screws to keep the latch horizontal and centered. Install the interior knob and tighten the set screw.
Image: The matte black door knob installed on a white door, with a clear view of the latch mechanism on the door edge.
- Install Strike Plate on Door Frame:
Install the strike plate on the door frame using the provided screws. Close the door and test the latch operation. If the latch is loose in the strike, adjust the strike tab so it grips the latch bolt better when the door is closed.
Image: An exploded diagram showing the individual components of the door knob and their assembly order.
Ntuziaka ọrụ
The Weiser Prague Passage Door Knob is a non-locking mechanism. To open the door, simply turn the knob in either direction. The latch will retract, allowing the door to open. To close, push the door shut, and the latch will automatically engage with the strike plate, holding the door in place.
Nlekọta
To maintain the finish and functionality of your door knob, follow these guidelines:
- Jiri nwayọ na-ehicha mgbe niile, damp ákwà. Zere ihe nhicha, ihe mgbaze, ma ọ bụ kemịkalụ siri ike, n'ihi na ihe ndị a nwere ike imebi njedebe.
- Do not use furniture polish or other household cleaners on the door knob.
- Periodically check and tighten any loose mounting screws to ensure secure operation.
Nchọpụta nsogbu
If you encounter any issues with your door knob, consider the following common solutions:
- Knob is Loose: Check if the mounting screws are securely tightened. If the interior knob is loose, ensure the set screw (if applicable for your specific variant) is tightened.
- Latch Not Engaging Properly: Verify that the strike plate on the door frame is aligned correctly with the latch bolt. The strike tab can be adjusted to provide a better grip if the latch is loose.
- Ọrụ siri ike: Ensure all components are installed without excessive force or misalignment. A small amount of silicone-based lubricant can be applied to the latch mechanism if needed, but avoid over-lubricating.
Nkọwapụta
| Njirimara | Nkọwa |
|---|---|
| Onye nrụpụta | Weiser |
| Nọmba akụkụ | 9GA1010-154 |
| Akụkụ ngwaahịa | 6.67 x 6.19 x 6.19 cm |
| Ibu Ibu | 744 g |
| Nha | Mkpọchi |
| Agba | Matte Black |
| Ụdị | Passage (Non-locking) |
| Mechaa | Ekpuchiri ntụ ntụ |
| Ihe onwunwe | Ọla |
| Ụdị | Gburugburu |
| Ndakọrịta oke ọnụ ụzọ | 1-3/8" - 1-3/4" |
| Latch Backset | 2-3/8" - 2-3/4" |
| Cross Bore | 2-1/8" |
| Atụmatụ pụrụ iche | Ọ dị mfe ịwụnye |
Akwụkwọ ikike
This Weiser Prague Passage Door Knob comes with a Nrụ ọrụ na akwụkwọ ikike imecha ndụ nwere oke. For specific terms and conditions, please refer to the warranty information provided with your product packaging or contact Weiser customer support.
Nkwado
For further assistance, technical support, or to inquire about replacement parts, please visit the official Weiser websaịtị ma ọ bụ kpọtụrụ ngalaba ọrụ ndị ahịa ha. Enwere ike ịchọta ozi kọntaktị na nkwakọ ngwaahịa ngwaahịa ma ọ bụ onye ọrụ nke ika ahụ websaịtị.
