Instruction Manual for DEDRA 18V Cordless Angle Grinder

Ngwaahịa gafereview

The DEDRA SAS+ALL DED7051 18V Cordless Angle Grinder is designed for cutting and grinding tasks. This tool features a powerful motor capable of reaching speeds up to 8500 RPM, compatible with 125 mm and 115 mm diameter discs. Its ergonomic design, lightweight construction (2.2 kg), and fiberglass-reinforced nylon housing ensure durability and comfortable operation.

Key features include a safety switch that interrupts power if excessive pressure is applied to the workpiece, preventing damage or overheating. The quick-release system for discs, a two-position side handle, and a rubberized grip enhance user comfort and control. The disc changing key is conveniently stored within the side handle.

Image: DEDRA 18V Cordless Angle Grinder, showing the main unit with the side handle and disc guard installed.

Ozi nchekwa

Na-agụ ma ghọta ịdọ aka ná ntị nchekwa niile, ntuziaka, nkọwa na nkọwapụta enyere na ngwa ike a. Ọdịda ịgbaso ntuziaka niile edepụtara n'okpuru nwere ike bute ujo ọkụ eletrik, ọkụ na/ma ọ bụ mmerụ ahụ dị egwu.

• Nchekwa mpaghara ọrụ: Debe ebe a na-arụ ọrụ ọcha na ọkụ nke ọma. Ebe mgbagwoju anya ma ọ bụ ọchịchịrị na-akpọ ihe mberede. Ejila ngwaọrụ ike rụọ ọrụ n'ime ikuku mgbawa, dị ka ọnụnọ mmiri ọkụ nwere ike ire ọkụ, gas ma ọ bụ uzuzu.
• Nchekwa Eletriki: Zenarị mmetụ ahụ n'elu ala ala ma ọ bụ n'ala, dị ka ọkpọkọ, radiators, akwa na friji. Enwere nnukwu ihe ize ndụ nke ujo eletrik ma ọ bụrụ na ahụ gị agbaala n'ala ma ọ bụ gbatuo.
• Nchekwa nkeonwe: Always wear eye protection. Use personal protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection for appropriate conditions.
• Iji na Nlekọta Ngwa: Amanyela ngwá ọrụ ike. Jiri ngwa ike ziri ezi maka ngwa gị. Ngwá ọrụ ike ziri ezi ga-arụ ọrụ ahụ nke ọma na nchekwa na ọnụego e mere ya.
• Mgbanwe nchekwa: The grinder is equipped with a safety switch that cuts off power if excessive pressure is applied to the workpiece. This prevents damage to the tool and potential overheating. Do not attempt to bypass or disable this safety feature.
• Ndakọrịta diski: Only use grinding and cutting discs with a diameter of 125 mm or 115 mm that are rated for the grinder's maximum RPM.

Kedu ihe dị na Igbe ahụ

Mgbe imepechara ngwugwu ahụ, biko chọpụta na akụrụngwa niile dị na enweghị mmebi:

• 1 x DEDRA 18V Cordless Angle Grinder (Main Unit)
• 1 x Auxiliary Side Handle
• 1 x Disc Guard
• 1 x Two-hole Wrench for Disc Change
• Note: Battery and charger are NOT included and must be purchased separately.

Image: A visual reminder that the battery and charger are sold separately from the angle grinder unit.

Melite

1. Ijikọta aka n'akụkụ:

   The auxiliary side handle can be screwed into either of the two threaded holes on the grinder's gear housing, depending on your preferred working position and hand dominance. Ensure it is tightened securely.

   

   Image: The angle grinder with the side handle attached, demonstrating its position.

2. Mounting the Disc Guard:

   Position the disc guard over the spindle housing. Rotate it until it covers the disc adequately for your application, providing maximum protection. Tighten the guard's clamping mechanism firmly to prevent movement during operation.
3. Installing the Grinding/Cutting Disc:

   Ensure the grinder is switched off and the battery is removed before installing or changing discs. Press the spindle lock button to secure the spindle. Place the inner flange onto the spindle, then position the grinding or cutting disc onto the inner flange. Secure the disc with the outer flange and tighten it using the provided two-hole wrench. Release the spindle lock.

   

   Foto: Top view of the angle grinder showing the disc guard and the spindle assembly where the disc is mounted.

4. Ịtinye batrị:

   Align the battery pack with the battery slot at the rear of the grinder handle. Slide the battery into place until it clicks securely. Ensure it is fully seated before operation.

   

   Foto: N'azụ view of the angle grinder, highlighting the battery insertion slot.

Ntuziaka ọrụ

1. Malite igwe ihe:

   With the battery inserted and disc securely mounted, hold the grinder firmly with both hands. Press the power switch to start the tool. Allow the disc to reach full speed before making contact with the workpiece.
2. Grinding and Cutting:

   Apply light, consistent pressure. Do not force the tool. The integrated safety switch will activate and cut power if excessive pressure is detected, protecting the tool from overload and overheating. If this occurs, reduce pressure and restart the tool.

3. Ịkwụsị igwe ihe:

   Release the power switch to stop the tool. Wait for the disc to come to a complete stop before setting the grinder down or performing any adjustments.

Nlekọta

• Nhicha: Regularly clean the ventilation openings of the grinder to prevent dust accumulation, which can lead to overheating. Use a soft brush or compressed air.
• Nyocha diski: Before each use, inspect the grinding or cutting disc for cracks, chips, or excessive wear. Replace damaged discs immediately.
• Nchekwa: Store the grinder in a dry, secure place, out of reach of children. Remove the battery when storing for extended periods.
• Nlekọta batrị: Follow the manufacturer's instructions for charging and storing the battery pack. Do not expose batteries to extreme temperatures or moisture.

Nchọpụta nsogbu

Nkọwapụta

Akwụkwọ ikike na nkwado

Dedra products are designed for quality and reliability, undergoing testing at every stage of their lifecycle to ensure high standards. While specific warranty details are not provided in this manual, for any product support, technical assistance, or warranty claims, please contact Dedra customer service or refer to the official Dedra websaịtị maka ozi kachasị ọhụrụ.

You can visit the official Dedra store on Amazon for more information and contact options: Dedra Store