Weiser GED1460X15 Keypad Lock User Manual

Okwu mmalite

This manual provides detailed instructions for the installation, operation, and maintenance of your Weiser GED1460X15 Keypad Lock. This electronic deadbolt offers keyless entry and enhanced security features, including SmartKey Re-Key Technology. Please read this manual thoroughly before installation and use to ensure proper function and to maximize the lifespan of your lock.

Ozi nchekwa

• Read all instructions completely before installing and operating the lock.
• Mara onwe gị na nkwupụta ịdọ aka na ntị na ịkpachara anya niile.
• Chedo koodu njirimara na koodu ukwu gị.
• Tụfuo batrị eji eme ihe dịka iwu na ụkpụrụ mpaghara siri dị.
• Do not attempt to disassemble or modify the lock beyond the instructions provided. This may void the warranty and compromise security.

Ihe ngwugwu

• Mgbakọ ahụ igodo mpụta
• Interior Assembly (with battery cover)
• Deadbolt Latch
• Efere efere
• Efere arịọnụ
• Ịkwanye kposara
• Keys (for SmartKey cylinder)
• Ntuziaka nwụnye na akwụkwọ ntuziaka onye ọrụ

Ntọala na nwụnye

1. Kwadebe Ọnụ ụzọ

Ensure your door is properly prepared for installation. The lock is designed for standard door thicknesses and backsets. Refer to the dimensions diagram for specific measurements.

Figure 1: Product dimensions, showing length, width, and height measurements for proper door fitting.

2. Install the Deadbolt Latch

Insert the deadbolt latch into the edge of the door. Ensure the 'UP' arrow on the latch is pointing upwards. Secure it with the provided screws.

Figure 2: The deadbolt latch mechanism, shown with accompanying SmartKey keys.

3. Install the Exterior Keypad Assembly

Feed the cable from the exterior keypad through the hole in the door and position the keypad flush against the door. Ensure the tailpiece passes through the center hole of the deadbolt latch.

Foto 3: N'ihu view of the Weiser keypad lock, displaying the numerical buttons and keyhole.

4. Wụnye Mgbakọ ime ụlọ

Connect the cable from the exterior assembly to the interior assembly. Mount the interior assembly onto the door, aligning the tailpiece with the turnpiece slot. Secure with screws through the mounting plate.

Foto 4: Akụkụ view of the interior unit of the lock, showing the battery compartment and manual turnpiece.

5. Wụnye batrị

The lock requires 4 AA batteries (not included). Remove the battery cover on the interior assembly and insert the batteries, observing polarity. Replace the battery cover.

6. Perform Door Handing Process

After battery installation, the lock will automatically perform a door handing process to learn the orientation of your door. This is crucial for proper operation. If the lock does not automatically hand, refer to the full installation guide for manual initiation.

Na-arụ ọrụ mkpọchi

Koodu onye ọrụ mmemme

Your lock can store up to 6 unique user codes. Refer to the full programming instructions for detailed steps on adding, deleting, and modifying codes. A master code is recommended for enhanced security and managing user codes.

Ọgụgụ 5: nso nso view of the keypad, highlighting the numbered buttons and the lock symbol.

Ịkpọchi ụzọ

• Mkpọchi ahụ igodo: Press the lock symbol button on the keypad. The deadbolt will extend.
• Mkpọchi onwe: If enabled, the lock will automatically re-lock after a set period (e.g., 30 seconds) once unlocked.
• Manual Locking (Interior): Turn the thumb-turn on the interior assembly to extend the deadbolt.

Ịkpọghe ụzọ

• Keypad Unlocking: Enter a valid user code on the keypad, then press the lock symbol button. The deadbolt will retract.
• Key Unlocking: Insert the physical key into the keyhole and turn it to unlock the deadbolt.
• Manual Unlocking (Interior): Turn the thumb-turn on the interior assembly to retract the deadbolt.

SmartKey Re-Key Technology

The SmartKey cylinder allows you to re-key your lock to work with any other SmartKey compatible key. Follow the specific instructions provided with your SmartKey tool for this process. This feature is useful for matching existing keys or changing keys without replacing the entire lock.

Figure 6: Visual representation of key features including one-touch locking, master code, user codes, bump-proof, pick-proof, and kick-in resistant design.

Nlekọta

Ngbanwe batrị

When the batteries are low, the lock will emit an audible alert and/or the keypad will flash red after a successful code entry. Replace all four AA batteries promptly to ensure continuous operation. Use only new, high-quality alkaline batteries. To replace, remove the interior battery cover, remove old batteries, insert new ones observing polarity, and replace the cover.

Nhicha

Clean the lock with a soft, damp ákwà. Zere ihe nhicha ma ọ bụ ihe mgbaze, n'ihi na ihe ndị a nwere ike imebi ihe ndị dị na ya na ihe ndị dị na eletrọniki.

Nchọpụta nsogbu

• Mkpọchi anaghị aza: Check battery levels. Replace batteries if necessary. Ensure the cable connection between interior and exterior assemblies is secure.
• Keypad anaghị agba ọkụ: Nke a na-egosikarị batrị ndị nwụrụ anwụ. Dochie batrị AA anọ niile.
• Deadbolt not extending/retracting fully: Ensure the door frame strike plate is properly aligned. Check for any obstructions in the door jamb. Re-run the door handing process.
• Koodu anaghị arụ ọrụ: Verify that the correct user code is being entered. If a master code is set, ensure it is used for programming. Try resetting the lock to factory defaults and reprogramming codes (refer to the full programming guide).
• Lock beeps continuously: This may indicate a low battery warning or an error. Check batteries first. If the issue persists, consult the full manual for error code interpretations.

Nkọwapụta

Akwụkwọ ikike na nkwado

For warranty information and technical support, please refer to the official Weiser website or contact their customer service. Keep your proof of purchase for warranty claims. Detailed contact information can typically be found on the product packaging or the manufacturer's websaịtị.