iFlight-LOGOiFlight B011639 BLITZ 1.6W VTX LED Indicator

iFlight-B011639-BLITZ-1.6W-VTX-LED-Indicator-PRODUCT

Product Information

The IFLIGHT BLITZ VTX 1.6W is a video transmitter designed for use in drones or other similar applications. It has a power output of 1.6W and supports multiple power levels including 25mW, 400mW, 800mW, and 1600mW. The VTX has a mounting pattern of 30.5*30.5mm and uses an MMCX interface for connectivity. It also features VTX telemetry using IRC Tramp technology. The weight of the VTX is 19g.

Product Usage Instructions

Mounting and Installation

  • Ensure that there is enough space around the VTX for proper air convection to dissipate heat. Insufficient cooling can trigger overheat protection and reduce or even switch off power transmission.
  • Before installation, read the instructions carefully for properwiring.

Power Connection

  • Make sure to connect the VBAT (Positive input) and GND (Negative) ports correctly to the power source.
  • Check the voltage range and ensure the correct positive and negative polarity before switching on the power to prevent component damage.

Antenna Installation

  • It is recommended to install the antenna before powering on the VTX to extend the module’s lifespan.
  • Note that antennas must be installed before powering on to prevent potential damage to the VTX.

Band and Channel Selection

  • Use the Band button (blue LED) to switch between bands (A to R). Press and hold the button for 2 seconds to switch the band.
  • Use the Channel button (red LED) to switch between channels (1 to 8). Short press the button to change the channel.

Output Power Selection

  • Short press the Power button to change the output power level.
  • The LED indicator will flash to indicate the selected power level: 1 flash for 25mW, 2 flashes for 100mW, and 3 flashes for 200mW.

Connection to Flight Controller (FC)

  • If using with an FC, connect the VTX to the FC using the following connections:
    • VTX 7-34V: Connect to the VO/VTX port on the FC.
    • GND: Connect to the GND port on the FC.
    • RX: Connect to the IRC Tramp signal input on the FC.
    • 5V OUT: Connect to the 5V power output on the FC.
    • VIDEO: Connect to the video signal input on the FC.
  • Enable the corresponding VTX IRC Tramp on UART port of the FC.

Connection without Flight Controller

  • If using the VTX without an FC, connect it as follows:
    • Battery: Connect to a power source with a voltage range of 7-34V.
    • GND: Connect to the ground.
    • Video: Connect to the camera’s video signal input.
    • Camera GND: Connect to the camera’s ground.
    • 5V: Connect to a 5V power source (optional).

BLITZ 1.6W VTX Instructions

iFlight-B011639-BLITZ-1.6W-VTX-LED-Indicator-FIG-1

LED Indicator and Function ButtoniFlight-B011639-BLITZ-1.6W-VTX-LED-Indicator-FIG-2

Frequency Table

Note: Antennas must be installed BEFORE powering on.
The VTX can be damaged when using without proper cooling.

 

BAND

CH
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
A 5865MHz 5845MHz 5825MHz 5805MHz 5785MHz 5765MHz 5745MHz 5725MHz
B 5733MHz 5752MHz 5771MHz 5790MHz 5809MHz 5828MHz 5847MHz 5866MHz
E 5705MHz 5685MHz 5665MHz 5645MHz 5885MHz 5905MHz 5925MHz 5945MHz
F 5740MHz 5760MHz 5780MHz 5800MHz 5820MHz 5840MHz 5860MHz 5880MHz
R 5658MHz 5695MHz 5732MHz 5769MHz 5806MHz 5843MHz 5880MHz 5917MHz

Specs:

  • Power levels:25mW/400mW/800mW/1600mW Mounting pattern: 30.5*30.5mm
  • Interface:MMCX
  • VTX telemetry:IRC Tramp
  • Weight:19g

Ports:

  • VBAT: Positive input GND: Negative
  • RX: IRC Tramp signal
  • input 5V OUT: 5V
  • power output  GND: Negative
  • VIDEO: Video signal input

Attention:

  1. Please keep enough space when you install the VTX to ensure air convection around the module for heat dissipation. Otherwise, the module will enable overheat protection and the power transmission will be reduced or even switched off.
  2. It is recommended to ensure the correct voltage range and the correct positive and negative polarity before switching on the power to avoid burning the components.
  3. It is recommended that before switching on the power, make sure that the antenna has been installed, it can extend the life of the module.
  4. Please read the instructions for proper wiring before use.

Connect VTX to FC

iFlight-B011639-BLITZ-1.6W-VTX-LED-Indicator-FIG-3

Connect VTX without FCiFlight-B011639-BLITZ-1.6W-VTX-LED-Indicator-FIG-4

Documents / Resources

iFlight B011639 BLITZ 1.6W VTX LED Indicator [pdf] Instructions
B011639 BLITZ 1.6W VTX LED Indicator, B011639, BLITZ 1.6W VTX LED Indicator, VTX LED Indicator, LED Indicator, Indicator

References

Leave a comment

Your email address will not be published. Required fields are marked *