IFC-BOX-NS53 Book Type Controller User Manual

Chassis Material: All aluminum alloy
Processor:
- Onboard Intel i5-1245U (10 cores, 12 threads, maximum turbo
  frequency 4.4 GHz)
- Onboard Intel i7-1255U (10 cores, 12 threads, maximum turbo
  frequency 4.7 GHz)

Architecture: Alder Lake-U
Memory: Supports 2 DDR5 4800MHz SODIMM memory slots, up to 64
GB

BIOS: AMI UEFI BIOS
Display Chip: Integrated Intel(R) Iris(R) Xe Graphics core
graphics card

Display Interface: 2 DP display interfaces
Front Panel I/O Ports:
- 1 power switch
- 1 LAN1 indicator light
- 1 hard disk indicator light
- 1 CLEAR CMOS button
- 2 DP display interfaces
- 3 I210-AT Gigabit Ethernet ports
- 1 I219-LM Gigabit Ethernet port
- 4 USB3.0 ports
- 1 4Ping power supply Phoenix terminal
- Support 1 Mini PCIE (support PCIE and USB2.0 signals, optional
  4G/WIFI/Bluetooth), with SIM card holder

Network Interface: 3 I210-AT Gigabit Ethernet ports, 1 I219-LM
Gigabit Ethernet port
Storage Interface:
- Supports 1 M.2 slot (M-Key 2280 supports SATA SSD and NVME SSD
  (X 1speed))
- Support 1 MSATA slot (support SATA SSD)

Product Usage Instructions

1. Application Planning

Transportation

Handle the controller with care during transportation to avoid
any physical damage. Use appropriate packaging materials if
needed.

Storage

Store the controller in a dry and cool place to prevent any
potential damage from humidity or extreme temperatures.

Unpacking and Inspecting Delivered Equipment

When unpacking, check for any visible signs of damage. If damage
is found, contact the supplier immediately.

Installation Method

Follow the installation instructions provided in the manual
carefully to ensure proper setup and functionality.

2. Device Connection

Precautions before Connection

Ensure that the device is powered off before connecting any
cables to avoid electrical hazards.

Connect the Device to the Power Supply

Use the provided power cable to connect the device to a stable
power source following the guidelines in the manual.

Daily Use and Maintenance

Frequently Asked Questions (FAQ)

Q: What operating systems are supported by the
IFC-BOX-NS53?

A: The IFC-BOX-NS53 supports Windows 10, Windows 11, Linux, and
other operating systems.

“`

View Fullscreen

IFC-BOX-NS53
Book Type Controller User Manual

For your personal safety and to avoid property damage, you must pay attention to the instructions in this manual. Instructions related to property damage are not accompanied by a warning triangle. Warning instructions are listed as follows according to the hazard level from high to low.
warn Indicates that if appropriate measures are not taken, the machine may be irreparably damaged. Notice Indicates that undesirable results or situations may occur if corresponding instructions are not paid attention to. The products/systems covered by this document may only be operated by qualified personnel who meet all work requirements. Its operation must comply with the instructions in the respective accompanying documents, especially the safety and warning instructions. Due to relevant training and experience, qualified personnel can perceive the risks of this product/system and avoid possible dangers. warn Yanling Industrial Control products are only allowed to be used in the use cases specified in the catalog and related technical documents. If you want to use products and components from other companies, you must obtain the recommendation and permission of Yanling Industrial Control. Correct transportation, storage, assembly, installation, commissioning, operation and maintenance are the prerequisites for the safety and normal operation of the product. The permissible environmental conditions must be guaranteed. The tips in the relevant documents must be noted.

Disclaimer Our company reserves the right to change this manual and will not notify you of any subsequent changes to the product. We are not responsible for any direct, indirect, intentional or unintentional damage or hidden dangers caused by improper installation or use. Before ordering a product, please consult your dealer to learn in detail whether the product performance meets your needs. All rights reserved. No reproduction by mechanical, electronic or other means is allowed without permission. Warranty Terms: The product warranty period is three years . If the user has other requirements, the contract signed by both parties shall prevail.

Table of Contents
1. Product Introduction ………………………………………………………………………..2 1.1 Product Overview ……………………………………………………………….2 1.2 Product Specifications ……………………………………………………….. 2
2. Application Planning ………………………………………………………………………. 3 2.1 Transportation …………………………………………………………………… 3 2.2 Storage ……………………………………………………………………………..3 2.3 Unpacking and inspecting delivered equipment ……………………. 3 2.4 Installation method ……………………………………………………………..4
3. Device Connection ………………………………………………………………………….4 3.1 Precautions before connection ……………………………………………. 4 3.2 Connect the device to the power supply ………………………………. 4
IV. Instructions for Use ………………………………………………………………………..5 4.1 Product appearance picture ……………………………………………….. 5 4.3 External Interface ……………………………………………………………….6 4.4 Status indicator …………………………………………………………………. 6 4.5 Installing internal accessories ………………………………………………7 4.6 Pin definition: ……………………………………………………………………..8 4.7 BIOS Setup ………………………………………………………………………. 9 4.7.1 Power-on auto-start function setting …………………….. 10 4.7.2 Timing power-on function setting …………………………. 10 4.7.3 COM port mode selection ……………………………………. 11
V. Daily Use and Maintenance ………………………………………………………….. 12
-1-

1. Product Introduction
1.1 Product Overview
IFC-BOX-NS53 is a book-type controller. The whole machine adopts Intel’s 12th generation Core i3/ i5/i7 processor and supports Windows 10, Windows 11, Linux and other operating systems. It is very convenient to use. The whole machine adopts an all-aluminum alloy structure and a fanless heat dissipation design . It has a simple structure and has good dustproof, heat dissipation, vibration resistance and EMC performance. It has high system reliability and strong environmental applicability.
1.2 Product Specifications

Machine Model IFC-BOX-NS53

Chassis Color Gray (color can be customized)

Chassis Material All aluminum alloy

Processor

Onboard Intel i5-1245U (10 cores, 12 threads, maximum turbo frequency 4.4 GHz) Onboard Intel i7-1255U (10 cores, 12 threads, maximum turbo frequency 4.7 GHz)

Architecture

Alder Lake-U

Memory

Supports 2 DDR5 4800MHz SODIMM memory slots, up to 64 GB

BIOS

AMI UEFI BIOS

Display Chip Integrated Intel(R) Iris(R) Xe Graphics core graphics card

Display Interface 2 DP display interfaces

Front Panel I/O Ports
Extensible Interface Network Interface

1 power switch, 1 LAN1 indicator light, 1 hard disk indicator light, 1 CLEAR CMOS button, 2 DP display interfaces, 3 I210-AT Gigabit Ethernet ports, 1 I219-LM Gigabit Ethernet port, 4 USB3.0 ports, 1 4Ping power supply Phoenix terminal Support 1 Mini PCIE (support PCIE and USB2.0 signals, optional 4G/WIFI/Bluetooth), with SIM card holder
3 I210-AT Gigabit Ethernet ports, 1 I219-LM Gigabit Ethernet port

Storage Interface

Supports 1 M.2 slot (M-Key 2280 supports SATA SSD and NVME SSD (X 1speed)) Support 1 MSATA slot (support SATA SSD)
-2-

Power Supply DC 12~24V wide voltage input

Product Size 205 * 146 * 50 mm

Machine Weight 1.54 kg (bare system)

Application Areas

Industrial automation, machine vision, medical, logistics and transportation, warehousing

2. Application Planning
2.1 Transportation
Packaged products can be transported to any location by any means of transportation. They must not be loaded in open cabins or carriages during long-distance transportation, nor stored in open warehouses during transit. During transportation, they must not be shipped in the same vehicle (or other means of transportation) with flammable, explosive, or corrosive items, and the products must not be exposed to rain, snow, or liquid substances, or mechanical damage.
2.2 Storage
The product should be stored in the original packaging box. The ambient temperature of the warehouse where the product is stored should be 0 40 and the relative humidity should be 20% 85%. No harmful gases, flammable and explosive products and corrosive chemicals are allowed in the warehouse, and there should be no strong mechanical vibration, impact and strong magnetic field. The packaging box should be at least 10cm above the ground and at least 50cm away from the wall, heat source, cold source, window or air inlet .
The device in cold weather , be aware of extreme changes in temperature. In this case, make sure that no water droplets (condensation) have formed on or inside the device. If condensation has formed on the device, wait at least 12 hours before switching on the device.
2.3 Unpacking and Inspecting Delivered Equipment
Please pay attention to the following points when unpacking the device: It is recommended that you do not discard the original packaging materials . Please keep the original packaging materials for use when transporting the device again. Please store the document in a safe place ; it will be required for initial commissioning of the device . Inspect the delivered equipment for any obvious damage that may have occurred during transportation. Verify that the shipment contains the complete device and any accessories you ordered separately. If
-3-

there is any discrepancy or shipping damage, please contact Customer Service.
2.4 Installation
Wall-mounted Guide rail installation Embedded VESA standard
3. Device Connection

3.1 Precautions before Connection

warn Connected or built-in peripherals must not be connected to devices with opposite polarity. warn This device can only be operated on a grounded power supply network . It is prohibited to operate it on an ungrounded power supply network . warn The rated voltage of the device used must comply with the power supply characteristics of this product. Notice Only connect peripheral devices approved for industrial applications. Hot-swappable I/O can be connected while the machine is running. Modules (USB) , I/O devices without hot-swap functionality can only be connected after the device is disconnected from the power supply.

3.2 Connect the Device to the Power Supply

To connect the device to a Power

Schematic diagram

-4-

source Connect the DC 12 V power adapter to the power input port 1 , and then press the power switch button on the front panel of the device. The device starts and the blue power light turns on.
1
warn The on/off button signal does not cut off the PC power!
4. Instructions
4.1 Product Appearance
4.2 Product Dimensions
-5-

4.3 External Interface
Machine Front View
2
1 34 5 6 7
Remark: The orange light above is the LAN1 indicator The green light below is the hard disk indicator

Serial Number

Interface Name

1 power switch

1 LAN1 indicator light
2 1 hard disk
indicator light 1 CLEAR CMOS 3
button 2 DP display 4
interfaces 4 Gigabit 5 Ethernet ports

4 USB 3.0 ports

1 4Ping power supply
7
Phoenix terminal

4.4 Status Indicator

Show

Meaning

LED

POWER

Machine status display

Not bright Always on

-6-

Describe The device is turned off or the power is disconnected
Machine running

4.5 Installing Internal Accessories
1. Remove the bottom cover , install the memory, hard disk , WIFI module, and other accessories (as shown below), cover the bottom cover , and lock the four silver M3X6 cross countersunk screws.
2. Remove the bottom cover, install the memory cooling pad (as shown below), cover the bottom cover, and lock the four silver M3X6 cross countersunk screws.

Dual memory

Single memory

warn
This operation is only suitable for customers who have purchased the IFC-BOX-NS53 barebone system. Customers who have already installed the internal accessories should not disassemble the chassis at will.
-7-

4.6 Pin Definition:

JP/CN FP1
JP/CN COM1/COM2
JP/CN

pin# 1 3 5 7 9
pin# 1 3 5 7 9
pin#

Signal HDD LED+ HDD LED-
Reset NC
Signal DCD/485-
TXD GND RTS
RI Signal

pin# 2 4 6 8 10
pin# 2 4 6 8 10
pin#

Signal PWR LED+ PWR LED-
PWRSW GND
Signal RXD/485+
DTR DSR CTS
Signal

Remark 6-8Switch 5-7Reboot
Remark
BIOS select RS232/RS485
Remark

JP4 JP/CN
GPIO1
JP/CN

1 -2 pin#
1 3 5 7 9 pin#

default Signal
GND GPIO1 GPIO3 GPIO5 GPIO7 Signal

twenty pin#
2 4 6 8 10 pin#

Power on and Signal
5V GPIO2 GPIO4 GPIO6 GPIO8 Signal

2-3 Power-on Remark
Remark

GPIO2 JP/CN

1 3 5 7 9 pin#

GND GPIO9 GPIO11 GPIO13 GPIO15 Signal

2 4 6 8 10 pin#

5V GPIO10 GPIO12 GPIO14 GPIO16 Signal

Remark

CPU_FAN JP/CN

1
3 pin#

GND
FAN_TAC1 Signal

2
4 pin#

12V
FAN_PWM1 Signal

Remark

USB3

VCC

USBD_D-

USBD_D+

GND

9 CUT AWAY 10

VCC USBD_DUSBD_D+
GND GND

Notice The identification method of the starting pin 1 among the pins on the motherboard is: 1. There
is a white bold silk screen mark or arrow mark; 2. The pin seen on the back of the motherboard is a square

hole.

-8-

4.7 BIOS Settings
The BIOS setup menu is divided into the following options (for specific BIOS settings, please consult the Yanling Industrial Control + customer service hotline):
Main: View BIOS information Advanced: BIOS option settings C hipset: display settings and audio settings Security: Security settings Boot: Boot option settings Save & Exit: Save & exit BIOS settings
warn Please do not change the BIOS settings at will to avoid causing the machine
to malfunction. -9-

4.7.1 Power-on Auto-Start Function Setting
Enter the BIOS setup interface, select < Advanced > < IT8786 Super IO Configuration > <AC Power Loss Control> , set the options, select “Power ON” to enable the power-on function when the incoming call is received, and change to “Power Off” to disable the power-on function when the incoming call is received .
4.7.2 Timing Power-on Function Setting
Enter the BIOS setup interface, select < Advanced > < S5 RTC Wake Settings > <Wake system from S5 >, and select the setting item in the pop-up box, as shown below:
– 10 –

4.7.3 COM Port Mode Setting
Enter the BIOS setup interface, select <Advanced> < IT8786 Super IO Configuration > <Serial Port 1/2 Configuration> , set the < COM Port Mode > item as follows:
– 11 –

5. Daily Use and Maintenance
1. When the machine is in normal use, please ensure that the machine works in a non-vibrating environment to avoid damage to the hard disk and internal accessories. 2. When using the machine, please note that the ambient temperature should be between -20 and 50 . 3. This machine uses casing heat dissipation. In order to ensure the heat dissipation effect of the machine, we strongly recommend that you clean the surface of the machine regularly every three months. In a dusty environment, it is recommended to clean the surface of the machine once a month. 4. To ensure efficient and reliable operation of the machine, we recommend that you clean and defragment the hard disk regularly every three months. 5. When using the internal slots of the machine, we strongly recommend that you do not plug or unplug while the power is on to avoid static electricity damage. When the machine encounters a power outage due to non-human factors, in order to ensure that the machine can work normally and reliably, we strongly recommend that you immediately disconnect the power supply of the machine and make sure that the power grid is stable before powering it on; 6. We recommend that the machine be used exclusively by a dedicated person.
– 12 –

6. Common Hardware Failures and Troubleshooting Methods

Serial Number
1

Fault Phenomenon
The device does not turn on after the power button is
triggered

Cause Analysis
The power adapter is not supplying power

Repair Method
It is recommended to plug in the three-core power cord tightly or change
the socket hole position; Replace the power adapter;

Motherboard damage

Return to factory for repair;

Check whether the computer starts

Maybe the

normally; check whether the running light

signal input is

in front of the monitor is on; check

not connected

whether the display part connection

properly.

cable is correct;

The display is in

“power saving”

Press any key on the keyboard

No image on the monitor

mode The hard disk power cable or

Check whether the power cable and data cable of the hard disk (the hard disk must

data cable is

have been installed with the system and

damaged.

can be booted) are loose or not .

Use a bootable CD to enter the system

Hard disk

(usually WINPE system) and check

system files are

whether the hard disk system is

damaged

damaged. If necessary, it is best to

reinstall the system.

There is a

continuous

“beeping” sound

after turning on the

No memory detected

Open the computer case and re-insert the memory.

machine

– 13 –

warn When it is necessary to open the computer case or enter the BIOS settings, non-professionals should follow the steps under the guidance of a technician.
– 14 –

Documents / Resources

IFC IFC-BOX-NS53 Book Type Controller [pdf] User Manual
IFC-BOX-NS53 Book Type Controller, IFC-BOX-NS53, Book Type Controller, Type Controller, Controller

References

User Manual