Ideao DC400 4K Visualizer / Document Camera
DC400, a document camera with a built-in mic, is compatible With a variety of software that supports the UVC & UAC protocols. It works out of the box with most UC software,e such as Zoom, Google Meet, Microsoft Teams, and more. Ideao’s VisualCaSoftware greatly enhances your lessons and presentations by unlocking DC400’s extensive feature set, such as video recording, snapshot, picture-in-picture, whiteboard, and annotation.
For more information, please visit:
Ideao VisualCam
https://funtechinnovation.com/software/ideao-visualcam/
IdeaoCam
https://funtechinnovation.com/software/ideaocam/
Package Contents
DC400 Overview
- Autofocus / Flip Button
- Press once: autofocus / Long press: flip image 0/1800
- LED Light Button
- Press to turn on the LED light. Three levels of brightness.
- Micro USB Port
- Micro USB Port
- Status Indicator
- Microphone
- Camera
- LED Light
- Hinge screws
Getting started with DC400
- Push a finger through an opening at the base of the DC400 to slightly tilt up the camera.
- Lift the other side of the arm, then pull and flip the camera head in the sequence and direction indicated by the arrows below.
- Adjust the camera head until it is horizontal to the shooting surface. Fully extend the arm to capture the maximum shooting area of A3.
- Plug in the USB cable and attach the cable organizer to the arm.
- For using DC400 as a webcam, long-press the AF button to rotate the image.
Specifications
Camera
| Max. Output Resolution & Frame Rate | 3840×2880 @15fps (To Capture A3 Image) 3840×2160 @30fps
1920×1080 @60fps |
| Video Compression | MJPG / YUY2 |
| Focus | On demand (AFS) |
| Minimum Focus Distance | 10cm / 3.9″ |
| Maximum Shooting Area | 420x297mm / 16.5×11.7” (A3 size) |
| Viewing Angle | 82° |
| Sensor | 13 Megapixel 1/3″ CMOS |
| F-Number | F2.2 ± 5% |
| G-Sensor | No |
| LED Lighting | Yes, 3 level |
| Pan / Tilt / Zoom | Yes, 10 digital zoom by software |
| Image Rotation | 0° / 180° |
| Support Power Line Frequency | 50/60 Hz |
Micorphone
| Built-in Microphone | Omnidirectional Microphone |
| Microphone Specifications | Sensitivity S 94dB SPL @1KHz Min-29 Typ-26 Max-23 dBFS SNR 64dB |
Others
| Connectivity | Micro USB to Type A 2.0 |
| Powered By | USB 2.0 5V/500mA |
| Protocol | UVC; UAC; Plug-and-play |
|
Operating System |
Windows 11, 10, macOS 10.15 or above, Chrome OS |
| Product Dimensions | Folded (LxWxH):
195 x 66 x 13 mm / 7.7 x 2.6 x 0.5″ |
| Net Weight | 380g/ 13.4 oz |
|
Package Contents |
DC400,
Quick start guide, USB cable (Micro USB to A), Cable organizer, Carry bag, |
Federal Communications Commission (FCC) Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instruction manual, may cause harmful interference with radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. For products available in the USA/Canada market, only channels 1~11 can be operated. Selection of other channels is not possible.
Caution
- Be careful not to pinch your fingers when moving the arm.
- Do not hold the arm or camera head when carrying the product.
- Avoid any impact on the camera head.
UK-REP
APEX CE SPECIALISTS LIMITED
89 PRINCESS STREET, MANCHESTER, M4HT, UK
EC-REP
APEX CE SPECIALISTS LIMITED
UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK
NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND
Documents / Resources
 |
Ideao DC400 4K Visualizer / Document Camera [pdf] User Guide DC400 4K Visualizer Document Camera, DC400, 4K Visualizer Document Camera, Visualizer Document Camera, Document Camera, Camera |