IDEAL-LOGO

IDEAL L5 Lever Push-In Wire Connectors

IDEAL-L5-Lever-Push-In-Wire-Connectors-PRODUCT

Specifications

Model Rating Depth Width Height Wire Combination Range
Model 52 2-Port 11.9 mm 0.2mm2 – 2.5mm2
Model 53 3-Port 16.1 mm 11.7 mm 0.2mm2 – 2.5mm2
Model 55 5-Port 24.5 mm 0.2mm2 – 4.0mm2
Model L2 2-Port 13.3 mm 0.2mm2 – 4.0mm2
Model L3 3-Port 0.14mm2 – 4.0mm2
Model L5 5-Port 30.4 mm 0.14mm2 – 4.0mm2

Product Usage Instructions

Strip Length

The recommended strip length for wire insertion is based on the model you are using.

Insertion

  1. Strip the wire to the recommended length.
  2. Insert the wire into the appropriate port based on the number of ports available on your model.
  3. Ensure the wire is fully inserted and secure.

Removal

  1. Gently pull the wire out of the connector port.
  2. Avoid excessive force to prevent damage to the wires or connectors.

FEATURES

Models 52, 53, 55, L2, L3 & L5

  • Do not exceed the rating of these connectors
  • Turn OFF the power before removing or installing connectors
  • Wiring must comply with all applicable electrical regulations
  • COPPER TO COPPER ONLY. Do not use on aluminium wire.
  • Incorrect use of these connectors can cause electrical fires, personal injury or death
  • Use only one conductor per port
  • Strip wires back 9 – 10mm (52, 53 & 55) / 11-12mm (L2, L3 & L5)
  • For solid and rigid stranded wire, grip the wire firmly and insert the conductor into the open port (lever does not need to be open)
  • For flexible stranded wire (>7 strands), lift the lever and insert the conductor into the open port. Close lever
  • Verify conductors are fully inserted into the back of the connector.
  • To remove a wire, lift the lever and pull out the wire

Installation Instructions

Strip LengthIDEAL-L5-Lever-Push-In-Wire-Connectors-FIG-1

InsertionIDEAL-L5-Lever-Push-In-Wire-Connectors-FIG-2

RemovalIDEAL-L5-Lever-Push-In-Wire-Connectors-FIG-3

Specifications

Specifications Model 52 2-Port Model 53 3-Port Model 55 5-Port
Rating 24 Amp / 450V / 85°C
Depth 21 mm
Width 11.9 mm 16.1 mm 24.5 mm
Height 11.7 mm
Wire Combination Range Solid, Rigid, Stranded and Flexible Wires 0.2mm2-2.5mm2

IDEAL-L5-Lever-Push-In-Wire-Connectors-FIG-4

Specifications Model L2 2-Port Model L3 3-Port Model L5 5-Port
Rating 32 Amp / 450V / 85°
Depth 18.6 mm
Width 13.3 mm 18.9 mm 30.4 mm
Height 8.8 mm
Wire Combination Range Solid and Rigid Stranded 0.2mm2 – 4.0mm2
Flexible Wires 0.14mm2 – 4.0mm2

IDEAL-L5-Lever-Push-In-Wire-Connectors-FIG-5

idealind.com

Frequently Asked Questions

Can I use these connectors with stranded wires?

Yes, these connectors are compatible with solid, rigid stranded, and flexible wires as specified in the wire combination range for each model.

What is the maximum wire combination range supported by Model L3?

Model L3 supports a wire combination range from 0.14mm2 to 4.0mm2

How do I know if the wire is fully inserted into the connector?

Ensure that the wire is inserted to the recommended depth specified for each model and that it is securely held in place.

Can I reuse these connectors?

These connectors are designed for single-use only to ensure optimal performance and safety.

Documents / Resources

IDEAL L5 Lever Push In Wire Connectors [pdf] Instruction Manual
52, 55, L2, L3, L5, L5 Lever Push In Wire Connectors, Lever Push In Wire Connectors, Push In Wire Connectors, Wire Connectors

References

Leave a comment

Your email address will not be published. Required fields are marked *