ICP DAS U-7524M CR UA I/O Series 5 Channels DO and 2 Port Ethernet Switch
Packing List
UA I/O package includes this document and the following items:
Technical Resources
How to search for drivers, manuals and spec information on ICP DAS website
- For Mobile Web
Technical Support - service@icpdas.com
- https://www.icpdas.com
- For Desktop Web
Preparations for Devices
- PC/NB: Can connect to the network and set the network
- Ethernet Switch/Hub (Ex: NS-205A or PoE Switch NSM-208SE)
- Power Supply: +12 ~ +48 VDC (Ex: MDR-60-24)
Hardware Connection
Connect the UA I/O Module with the RJ-45 Ethernet port to an Ethernet switch/hub (Fig.2 for PoE Switch) and PC. You can also directly link the U-75xx to PC with an Ethernet cable. After power is connected, please【wait 1 minute】for U-75xx start-up procedure. When the “RUN” light starts flashing, it represents the boot is complete.
Network Connection
| Factory Default Settings of U-75xx | |||
|
Network |
IP | 192.168.255.1 | Assign U-75xx a new IP setting according to your case. |
| Mask | 255.255.0.0 | ||
| Gateway | 192.168.1.1 | ||
| Web UI Account | Username | root | After login, change the username/ password at once. |
| Password | root | ||
- Change the PC’s IP setting as following. (Write down the PC original network settings before modify.) EX:
| IP | 192.168.255.10 |
| Subnet mask | 255.255.0.0 |
| Default Gateway | 192.168.1.1 |
- Make sure the PC and U-75xx is connecting through Ethernet. And then open a PC side browser (Ex: Chrome, IE…). Type http://192.168.255.1 in the URL address. Use default Web UI username/password root/root to login.
- Change the Username/password in 【Account Setting】of 【System Setting】, or user cannot use any other function
- Click【System Setting】【Network Setting】>【Network Setting(LAN)】to change the IP settings by user network
- Save the IP settings, restore the PC original IP settings, and then type the new IP/Username/Password in the browser to login the Web UI of U-75xx to configure user’s UA project
AI/AO Jumper Setting
To change the Selection Jumpers for Analog channels:
| U-7528M | ||
| Channel | ||
| Jumper | ||
| Channel | V/Iout6+ | V/Iout7+ |
| Jumper | J1 | J2 |
Remove the top case and upper board of the module, the selection jumpers are next to the connector.
| U-7502M | ||
| Channel | Vin1± | Vin0± |
| Jumper | J2 | J1 |
| Channel | Vin2± | |
| Jumper | J3 | |
| U-7528M | ||
| Channel | ||
| Jumper | ||
| Channel | V/Iout6+ | V/Iout7+ |
| Jumper | J1 | J2 |
| U-7517M-10 | |||||||||
| Channel | Vin8± | Vin7± | Vin6± | Vin5± | Vin4± | Vin3± | Vin2± | Vin1± | Vin0± |
| Jumper | J9 | J8 | J7 | J6 | J5 | J4 | J3 | J2 | J1 |
| Channel | Vin9± | ||||||||
| Jumper | J10 | ||||||||
Jumper Location Figure
| U-7504M | ||||||||
| Channel | Vin3 | Vin2 | Vin1 | Vin0 | Vout3 | Vout2 | Vout1 | Vout0 |
| Jumper | J4 | J3 | J2 | J1 | J8 | J7 | J6 | J5 |
| U-7524M | ||||
| Channel | Vout3+ | Vout2+ | Vout1+ | Vout0+ |
| Jumper | J4 | J3 | J2 | J1 |
| U-7526M | ||||||||
| Channel | Vout1 | Vout0 | Vin5 | Vin4 | Vin3 | Vin2 | Vin1 | Vin0 |
| Jumper | J8 | J7 | J6 | J5 | J4 | J3 | J2 | J1 |
| U-7517M | ||||||||
| Channel | Vin7± | Vin6± | Vin5± | Vin4± | Vin3± | Vin2± | Vin1± | Vin0± |
| Jumper | J8 | J7 | J6 | J5 | J4 | J3 | J2 | J1 |
| U-7519ZM | ||||||||||
| Channel | CH0± | CH1± | CH2± | CH3± | CH4± | CH5± | CH6± | CH7± | CH8± | CH9± |
| Jumper | J1 | J2 | J3 | J4 | J5 | J6 | J7 | J8 | J9 | J10 |
- Set up the Jumper corresponding to the type of Voltage / Current and Input / Output for each analog channel.
Voltage Input Selection Jumper (Jumpers default: Voltage
- Voltage Input (Single-ended Mode) Selection Jumper
- Voltage Output Selection Jumper
- Current Input Selection Jumper
- Current Output Selection Jumper
- Thermocouple Input Selection Jumper
Documents / Resources
 |
ICP DAS U-7524M CR UA I/O Series 5 Channels DO and 2 Port Ethernet Switch [pdf] User Guide U-7524M CR UA I O Series 5 Channels DO and 2 Port Ethernet Switch, U-7524M CR UA I O Series, 5 Channels DO and 2 Port Ethernet Switch, 2 Port Ethernet Switch, Ethernet Switch |
