ICON PROCESS CONTROLS PA5000 Audible and Visual Alarm Plus Display Controller

Specifications

General
Display	Displayed Values Stability Transmission Parameter Protection Class
Input Signal | Supply	Standard Voltage Current: 4-20mA (std.) | 0-20mA | 0-5V* | 0-10V* 85 – 260V AC/DC | 16 – 35V AC, 19 – 50V DC*
Output Signal | Supply	Standard Voltage 4-20mA 24VDC
Performance	Accuracy Accuracy According to IEC 60770 – Limit Point Adjustment | Non-Linearity | Hysteresis | Repeatability
Temperatures	Operating Temperatures
Materials | Wetted	Housing Polycarbonate
Part Number	PA5000

Product Usage Instructions

Basic Requirements and User Safety Guidelines

• Do not use the unit in areas threatened with excessive shocks, vibrations, dust, humidity, corrosive gases, and oils.
• Avoid using the unit in areas where there is a risk of explosions.
• Avoid using the unit in areas with significant temperature variations, exposure to condensation, or ice.
• The manufacturer is not responsible for damages caused by inappropriate installation or not maintaining proper environmental conditions.
• If there is a risk of serious threats due to unit malfunction, use additional systems to prevent accidents.
• Ensure to switch off and disconnect the unit from the power supply before troubleshooting.
• Do not attempt to disassemble, repair, or modify the unit yourself.

Programming the 4-20mA Input
Steps:

1. Press ESC/MENU Button for 3 Sec.
2. Press DOWN Arrow 2 times.
3. Press ENTER Button.
4. Press DOWN Arrow 4 times.
5. Press UP or DOWN Arrow to adjust value.
6. Press ENTER Button for 2 Sec.
7. Press DOWN Arrow.
8. Press ENTER Button.
9. Press ENTER Button for 2 Sec.
10. Press ESC/MENU Button twice.

Quick Start Manual

Read the user’s manual carefully before starting to use the unit. Producer reserves the right to implement changes without prior notice.

Symbol Explanation

This symbol denotes especially important guidelines concerning the installation and operation of the device. Not complying with the guidelines denoted by this symbol may cause an accident, damage or equipment destruction.

Basic Requirements | User Safety

• Do not use the unit in areas threatened with excessive shocks, vibrations, dust, humidity, corrosive gasses and oils.
• Do not use the unit in areas where there is risk of explosions.
• Do not use the unit in areas with significant temperature variations, exposure to condensation or ice.
• The manufacturer is not responsible for any damages caused by inappropriate installation, not maintaining the proper environmental conditions and using the unit contrary to its assignment.
• If in the case of a unit malfunction there is a risk of a serious threat to the safety of people or property additional, independent systems and solutions to prevent such a threat must be used.
• The unit uses dangerous voltage that can cause a lethal accident. The unit must be switched off and disconnected from the power supply prior to starting installation of troubleshooting (in the case of malfunction).
• Do not attempt to disassemble, repair or modify the unit yourself. The unit has no user serviceable parts.
• Defective units must be disconnected and submitted for repairs at an authorized service center.

Specifications

General
Display	LED | 4 x 20mm High | Red | Adjustable Brightness
Displayed Values	-999 ± 9999
Stability	50 ppm | °C
Transmission Parameter	1200…115200 bit/s, 8N1 / 8N2
Protection Class	NEMA 4X | IP67

Input Signal | Supply
Standard	Current: 4-20mA (std.) | 0-20mA | 0-5V* | 0-10V*
Voltage	85 – 260V AC/DC | 16 – 35V AC, 19 – 50V DC*

Output Signal | Supply
Standard	4-20mA
Voltage	24VDC

Performance
Accuracy	1% @ 25°C One Digit
Accuracy According to IEC 60770 – Limit Point Adjustment | Non-Linearity | Hysteresis | Repeatability

Temperatures
Operating Temperatures	-40 – 158°F | -40 – 70°C

Materials | Wetted
Housing	Polycarbonate

Part Number	Input	Display
PA5000	4-20mA	Single

Front Panel Description

Wiring Diagram

Function of Push Buttons

Programming 4-20mA Input

Programming 4-20mA Output

Calculating 4-20mA Input

SENSOR TYPE	20mA Set Point
Submersible	Range of sensor / Specific Gravity = 20mA
Ultrasonic	Tank Height
Radar	Tank Height

Programming Relays

24-0188 © Icon Process Controls Ltd.

Documents / Resources

ICON PROCESS CONTROLS PA5000 Audible and Visual Alarm Plus Display Controller [pdf] Owner's Manual PA5000 Audible and Visual Alarm Plus Display Controller, PA5000, Audible and Visual Alarm Plus Display Controller, Alarm Plus Display Controller, Display Controller, Controller

References

• User Manual