207-D5xx Series Ether CAT Digital Slave
“
Specifications
- Serial interface: Fast Ethernet, Full-Duplex
- Distributed Clock: 1ms
- Cable type: CAT5 UTP / STP Ethernet cable
- Surge protection: 10KV
- Transmission speed: 100Mbps
- I/O isolation voltage: 3750Vrms
- Input types: NPN / PNP type
- Input impedance: 5.6K / 0.5W
- Output type: NPN: open collector Darlington; PNP: MOSFET-P;
Integral suppression on diodes for inductive loads - Switch capacity: Each output Ch. is 100mA at 24VDC
- Response time: On to Off, about 50s; Off to On, about 10s
- Over current protection
- Power input
- Power consumption: 6W typical
Product Usage Instructions
Installation
1. Ensure power is disconnected before installation.
2. Use the pluggable terminal block with spring plug connectors
for easy wiring.
3. Set the address using the DIP switch according to your
network configuration.
4. Mount the module on a DIN rail using the specified dimensions
(L-122 x W-65 x H-104 mm).
Connection
1. Use a CAT5 UTP / STP Ethernet cable to connect the
module.
2. Connect the RJ45 phone jack to the appropriate network
interface.
Usage
1. Refer to the user manual for specific input and output
configurations.
2. Ensure proper input impedance and type settings for accurate
operation.
3. Monitor the LED diagnostic indicators for troubleshooting and
status checks.
FAQ
Q: What is the maximum transfer rate of the module?
A: The module supports a maximum transfer rate of 100Mbps.
Q: How can I set the module address?
A: Use the DIP switch provided on the module for address
setting.
Q: What is the power consumption of the module?
A: The typical power consumption of the module is 6W.
“`
01 EtherCAT Digital Slave
02 EtherCAT Analog Slave
207-D5xx Series
EtherCAT® Digital Slave 96-Ch. Digital input / output NPN/PNP type
Features
96-Ch. DI/O slave module with NPN/PNP type Max. 100Mbps transfer rate Easy installation with RJ45 phone jack and LED
diagnostic Pluggable terminal block with spring plug connectors DIP switch for address setting DIN rail mounting (L-122 x W-65 x H-104 mm)
Specifications
Serial interface
Fast Ethernet, Full-Duplex
Distributed Clock
1ms
Cable type
CAT5 UTP / STP Ethernet cable
Surge protection
10KV
Transmission speed 100Mbps
I/O isolation voltage 3750Vrms
Input types
NPN / PNP type
Input impedance
5.6K / 0.5W
Input current
±5mA(Max)
Output type
NPN: open collector Darlington; PNP: MOSFET-P; Intergral suppression on diodes for inductive loads
Switch capacity
Each output Ch. is 100mA at 24VDC
Response time
On to Off, about 50s; Off to On, about 10s
Over current protection
Power input
1A (Max) for each port (8-Ch.) 24VDC±10%
Power consumption 6W typical
Working temperature 0 to 60°C
Ordering Information
207-D560-NX/PX 96-Ch. Digital Input (DI) with NPN/PNP type
207-D542-NN/PP
64-Ch. Digital Input (DI) and 32-Ch. Digital Output (DO) with PNP type
207-D533-NN/PP
48-Ch. Digital Input (DI) and 48-Ch. Digital Output (DO) with PNP type
SCB-1BB-06A/10A CAT5 LAN cable, 0.6M/1M/2M/3M/5M/10M
/20A/30A/50A/A0A
Dimensions and Drawing
03 EtherCAT Motion Slave
04 EtherCAT Microstep Driver
05 EtherCAT Start-KIT
Remarks: 1.
2. ODM/OEM is available. 3.
1-10
Documents / Resources
 |
iBASE 207-D5xx Series Ether CAT Digital Slave [pdf] Owner's Manual 207-D560-NX-PX, 207-D542-NN-PP, 207-D533-NN-PP, 207-D5xx Series Ether CAT Digital Slave, 207-D5xx Series, Ether CAT Digital Slave, CAT Digital Slave, Digital Slave |