HZTZ Mini Label Printer

Overview
The Mini Label Printer (Model C50) prints thermal, temperature-sensitive labels using a USB-C power input and built-in rechargeable lithium battery. It supports label widths from 15–50mm and provides LED status indicators for charging, battery, and print readiness.
Specifications
| Product Model | C50 |
|---|---|
| Size | 85 x 102 x 48 mm |
| Resolution | 203 dpi |
| Input | 5V 1A |
| Connector | USB-C |
| Battery Capacity | 1200mAh (3.7V) |
| Consumable Size | 15–50 mm |
| Print Method | Thermal (temperature-sensitive) |
Quick Setup
- Download the app/driver resources: Scan the QR codes to download the mobile application, instructional videos, and device drivers.
- Install label paper: Pull up the paper cover to open the compartment, insert the label roll with the heat-sensitive printable side facing the print head, pull a small lead of paper out, and adjust the internal paper guides to match 15–50mm paper width. Ensure the paper is straight and centered, then close and lock the cover.
- Charge the printer: Connect a mobile power bank or phone charger adapter to the USB-C charging port.
- Power on: Long press the power button for 3 seconds.
- Print device configuration QR (optional): Short press the power button 2 times continuously.
- Calibrate paper (as needed): Short press the power button 6 times continuously.
App and Resources Download
- Available on the App Store and Google Play
- Scan to watch the instructional video

Product Introduction
- Power On/Off: Long press for 3 seconds.
- Print QR Code: Short press 2 times continuously to print the device configuration QR code.
- Calibrate Paper: Short press 6 times continuously to calibrate the label paper.
Label Paper Outlet
- Supports label paper widths from 15mm to 50mm.
USB-C Charging Port
- Connect to a mobile power bank or phone charger adapter to recharge.
Power Indicator Status
- Solid Green: Normal operation / Fully charged / Printing.
- Slow Flashing Green: Charging in progress.
- Solid Red: Out of paper / Paper bin open / Print head overheating.
- Slow Flashing Red: Low battery warning.
- Solid Blue: Bluetooth connection stable.
- Slow Flashing Blue: Bluetooth connection interrupted or abnormal.
Installation of Consumables
Placing Label Paper


- Pull up the paper cover in the direction of the arrow to open the compartment.

- Insert the label roll. Ensure the heat-sensitive printable side faces the print head, and pull a small lead of paper out of the exit path.

- The printer contains adjustable paper guides on both sides of the compartment.

- Adjust the internal paper guides to fit the specific paper width being used (15mm to 50mm).

- Ensure the paper is straight, centered, and margins are flush with the paper outlet before closing the cover.

Placing Tattoo Paper
This printer can print on 2-inch tattoo transfer paper. Use the following steps:
Peel off the transparent protective layer from the middle of the tattoo sheet, then peel off the yellow backing paper, leaving only the active ink carbon paper and white transfer sheet. Insert the white transfer paper front-side first into the feed slot. The printer will automatically feed and load the media.
The side with color is the front.
Safety & Precautions
- 1. Contains a built-in lithium battery. Do not operate in environments exceeding 40°C. Keep away from fires, direct heat sources, and enclosed hot areas (e.g., inside a vehicle under direct sunlight).
- 2. Children should operate and charge this device only under close adult supervision. Unplug the charging cable immediately after reaching full charge to prevent overheating, short circuits, or fire hazards.
- 3. Avoid exposing the product to moisture or open flames to protect the battery unit.
- Important Note: ⚠ Thermal paper is single-sided print only. Ensure the printable side is facing the correct direction during installation.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.
Troubleshooting
- Blank paper output / No content printed: Verify the paper roll is loaded in the correct direction. If correct, perform a self-test page print by pressing the power button twice. If the self-test prints fine, check your application settings or template. If the self-test fails, contact support.
- Blurry print / Faded print: Adjust the default print density settings inside the application. Clean the print head carefully using an alcohol swab to remove debris. Use genuine thermal paper rolls.
- Paper shortage error: Check whether the roll is empty. If paper is present, ensure the printer cover is fully snapped and locked closed (a loose cover can cause alignment detection errors).
- Printing stops mid-job: The printer may halt due to a paper jam, data transmission error, overheating detection, or low battery level. Check the status indicator LED and app alerts for exact diagnostic codes.
Documents / Resources
![]() | Mini Label Printer |
References
- App 下载jump.app.luckjingle.com
- LuckJingle |Portable Thermal Printer| Label Printerwww.luckjingle.com
- LuckJingle Documents and Driverswww.luckjingle.com
- LuckJingle Documents and Driverswww.luckjingle.com
- User Manualmanual.tools


