HUTT DDC56 Window Cleaning Robot Double User Manual

To remove the robot, hold the safety cable, stop the robot, and
take it down carefully.
If remote control is not available, use the safety rope to
guide the robot back for removal.

Frequently Asked Questions (FAQ):

Q: Can I use concentrated cleaning liquid with this
product?

A: No, using concentrated cleaning liquid is strictly prohibited
as it may block the spray hole and pump.

Q: What should I do if the robot cannot stick to the glass
surface?

A: Check whether the holder is properly buckled up to avoid air
leakage which may prevent sticking.

Q: Can the robot be used on broken or cracked glass
surfaces?

A: No, do not use the robot on broken or cracked glass as it may
lead to accidents.

“`

View Fullscreen

ENGLISH
4 ENGLISH

PARTS LIST

Sideview

Water tank cover ON/OFF/Pause Button
Press and hold for 3 seconds: Switch on/off Short press: start/continue/pause
Status Indicator
Buzzer
Power Cord Hole

Cord installed Port

Nozzle

Mop Holder
(normally not disassembled, Direct load wipes )

Nozzle ENGLISH 5

CONTENT OF THE BOX

Window Cleaning Robot x1

Mop Holder x2 (installed)

Remote Control x1

Mops x6

Safety Cable x1

Adapter x1

AC wire x1

Water Bottle x1 User Manual x1 6 ENGLISH

INSTALLATION INTRUCTIONS
Ensure the knob of the safety cable is fully tightened to the frame.
We recommend to fasten the buckle side of the safety cable to an object which is strong enough and will not be dragged, and reserve a suitable length for the device to work.
Cover each mop holder with a mop.
If there are sand and dust on the glass surface, it is recommended to clean it manually first to avoid scratching the glass when the robot is working. If manual cleaning is not possible, it is recommended to turn off the water spray function and use dry mops to wipe off the sand and dust first.
ENGLISH 7

Fill the water tank and cover with the plug
This product cannot be drenched, dry the surface residual moisture after filling with water. Using concentrated cleaning liquid in this product is strictly prohibited, so as not to block the spray hole and pump.
Please make sure the Mop Holder is installed inproper position before use
After the holder is installed, please observe from sideways 360o to ensure that each snap is stuck in place to avoid air leakage.
8 ENGLISH

Insert the windows cleaner power cord into the end of the adapter and tighten them. Connect the two ends of the AC wire to the adapter and the socket respectively.
Long-press the power button (more than 3 seconds), and the robot will turn on. After the fan is running, attach the robot on the glass at a location far away from the window frame.
If the robot can’t suck on glass, please check whether the holder has buckled up to cause air leakage.
Power/Start button
ENGLISH 9

INSTRUCTION AND CAUTIONS
Safety Rope
Check whether the safety rope is intact and is on a stable object.
Working Environment Inspection
Ensure the glass surface is dry, please do not use it when it is raining or when the glass surface is foggy. Do not use on broken and cracked glass. If outside working at height is required, ground safety warnings must be set up to prevent accidental personal injury. The robot cannot be used when there are stickers or oil on the glass surface, to avoid robot slipping and falling from glass.
Wet and Dry Wipe
If there are sand and dust on the glass surface, it is recommended to clean it manually first to avoid scratching the glass when the robot is working. If manual cleaning is not possible, it is recommended to turn off the water spray function and use dry mops to wipe off the sand and dust first. If there are only dirt stains, it can be wiped directly with the water spray (default turn on water spray). If there is slipping and twisting when the robot climbing, please install a dry wipe and turn on the water spray. If there are small areas of stubborn stains, you can use “spot cleaning” and turn on the water spray. If the robot has serious shaking or rattling, please install a dry wipe cloth.
Start
Ensure the power cord and plug are completely connected. Long press the Start /Power button (more than 3 seconds) the robot will turn on. After the fan is running, attach the robot on the glass to a location far away from the window frame. Ensure the robot has been stuck to the glass and then let go. Short press the power button to start the robot.
Remove Robot from Glass
When the robot is running, hold the safety cable with one hand, short press to stop the robot and take it down with the other hand. If you cannot reach the robot, and do not have the remote control on hand, please stay close to the glass to drag the safety rope, and slowly pull the robot back to the location reachable by hand, then remove the robot from the glass after powering off. After completely taking down the robot, long-press the power button (more than 3 seconds) to turn it off.
Power Outage Protection
This robot is equipped with an internal battery, which can hold on the robot for twenty minutes in case the robot is accidentally removed from the power cord and it will raise an audible and visual alarm. Please take down the robot as soon as possible. When the light indicator is red before turning on the device, it means the internal battery is too low to start the robot. Please, keep the robot connected to the electricity to charge it until the red lamp is off.
10 ENGLISH

PATH PLANNING
Put the windows cleaner in the centre of the glass far away from the window frame. Long press the Power/Start button to turn the robot on, and then short press the button to start it. The robot will automatically move upward, then move right. At last, it will reach the top right corner of the glass. After the robot has reached the top right corner; it will start to clean the glass by drawing an S-shaped curve from top to bottom. If the robot’s water spray function is turned on, when the robot works forward to the right, the right nozzle sprays water and the left nozzle does not spray water. When the robot works forward to the left, the left nozzle spray water, and the right nozzle does not spray water. After completing the cleaning, the robot will stop at the lower-left or right corner according to the glass shape.
ENGLISH 11

SPOT CLEANING ROUTE

Spot Wiping:
In the user specified area range, the robot will start up and down cleaning at Spot Cleaning.

MEANINGS OF LED INDICATOR LAMP AND VOICE

Status Indicator Charging indicator Status Indicator

LED lndicator
Green Light Green Light Three Long Beep Red Light
Red Flashing
Red and Green Alternation

Means
Working normal.
Window cleaning is complete.
The built-in battery power is insufficient, please charge 15 minutes above to turn on the robot.
The robot is disconnected; please connect the power supply or remove the robot from glass. Insufficient suction power; please check if the robot is air leaking. Friction with the glass is too large or too small, replace the wipe cloth accordingly.
Robot error, please contact customer service staff.

12 ENGLISH

REMOTE CONTROL

Start(x1)/Pause /Continue

To Top/Bottom Left/Right Stop at the end of the glass

Water spray on/off
Universal remote control, this machine does not have this function

Cleaning twice Spot Cleaning

To p revent m isuse by c hildren, please press p ause button b etween c ommands v ia remote controller. Otherwise, the controller c ommands b utton i s i nvalid
ENGLISH 13

PARAMETERS

Model: Voltage: Watt: Decibels: Size: Current: Capacity
UPS Battery Using Time
Suction Power Minimum Using area

DDC56 24V 72W
70db 269.3* 136.8* 77.5mm 300mA 650mAh Approx 25 mins (the remaining power of Built-In Battery will affect the time) 2000-3000pa 300300mm

WATER TANK MAINTENANCE
Please Ensure water or solution do not spill out of the water tank If accidentally spilled, please dry immediately to avoid causing water damage to the robot. When the robot is not in use, please Ensure there is no residual liquid in the water tank. If you use solution for cleaning, it is recommended to pour out the solution and then fill with a little fresh water to clean the water tank, and do not left any water in the tank.
Ensure there is not impurities in the added solution to avoid blocking the nozzle and pump.

14 ENGLISH

TROUBLESHOOTING
When the error indicator is flashing red with continuous and short sounds, please inspect if:
The plug of the power cord is loosened or damaged and results in power off or poor contact. The glass or mop is too wet and results in too low friction. The glass has impurities attached and results in too high friction. The mop holder is incorrectly installed and results in air leakage. The glass surface has sticky objects causing too much friction on the wipe The suction port is blocked.
The error indicator is flashing red and green alternately with alarming sound. It means trouble occurs on the inside hardware of the robot, please contact the customer service directly. On the condition of special glass, when cleaning the bottom of glass, it needs more time for cleaning up, please use remote control. In the case of the robot can’t walk freely, please change the mop or inspect the screws on the cleaning roller, ensure they are not loosened. If the robot mop holder shakes too strong when the robot is working, please check if the wipe cloth is too wet, and replace with a dry cloth. There will be a little delayed water spraying when the robot start to work, this is a normal phenomenon.
After cleaning, there’s residual round marks on the glass surface, please change a new mop. After completing the whole process of cleaning, the robot continues to move and doesn’t stop automatically, press the Pause Button and take it down. When it is in use, maybe bug occurs occasionally, please restart the robot as the solution. If there is a downward sliding when the robot is working, please inspect if:
The cloth is too wet or too dirty. The robot cannot resume work after a while, replace it with a dry and clean wipe cloth. The cloth is too dry to cause slips, turn on the water spray function to moisten the wipe cloth, then the robot can resume work.
Cause of Air Leakage,please inspect if:
The mop holder is installed correctly. The wipe cloth installation for flatness. The surface of the glass or other targeted surface are curved or covered with an uneven-surfaces such as stickers. The robot goes to the window frame, the mop holder will be warped to produce a wide range of air leakage.
ENGLISH 15

SAFETY
Usage requirements:
Make sure the safety rope is not broken, and fixed in an immovable object when use the robot. When need to work at height outside, you must set up a ground safety warning to prevent falling accidental personal injury. Do not drenched with water. Do not use in the rain or glass humid and foggy. Do not use on cracked and broken glass, confirm that the window area is larger than 30*30cm (height) before use, Please check if the glass with super narrow frame, beveled frame, beveled glass, no frame or glass glue with uneven, raised, leaking seams, gaps and other abnormal situation, use the remote control to control the robot if necessary. * Not recommended or need to be guarded to use on above situation, abnormal used environment may cause a fall. Be sure to turn off the robot when cleaning the surface of the robot to avoid danger during the movement of the robot. Please place the robot and accessories out of the reach of children and forbid children to operate this product. When the robot is working, it is strictly prohibited for fingers and any part of the body to touch this product. Please use this product following the instructions, please contact customer service if you can not troubleshoot. Do not repair by yourself to avoid danger. Only for 32°F~108°F (0°C ~ 40°C) home environment temperature, when the temperature is lower, it is recommended to use anti-freeze glass water. The storage environment should be dry, avoid direct light, please do not store the robot with oil, gas, flammable items.
Battery&Charging:
Do not use third-party adapter and do not disassemble and modify the robot, battery and adapter. Do not continue to use the charger if it is damaged or broken,please contact customer service. Place the adapter away from heat sources. If the product is to be shipped,it is recommended that in its original packaging with the robot turned off. If you do not use the product for a long time, please fully charge and shut down the robot and placed in a cool, dry place. At least every 3 months to charge once to avoid the battery over discharge and shortage the battery lifetime.
16 ENGLISH

Documents / Resources

HUTT DDC56 Window Cleaning Robot Double [pdf] User Manual
DDC56, DDC56 Window Cleaning Robot Double, DDC56, Window Cleaning Robot Double, Cleaning Robot Double, Robot Double, Double

References

User Manual

HUTT DDC56 Window Cleaning Robot Double User Manual

DDC56 Window Cleaning Robot Double

Product Information

Specifications:

Product Usage Instructions

Installation Instructions:

Filling and Preparation:

Powering On and Usage:

Removal and Safety: