HUNTER NODE-BT Bluetooth Enabled Battery Operated Controller User Guide

HUNTER-logo

HUNTER NODE-BT Bluetooth Enabled Battery Operated Controller

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller-product

  1. Battery check LED
  2. Active station indicator LEDs
  3. Manual station stop: Hold button to stop active station.
  4.  Manual station start: Hold button to select station indicated by the station LED. Release button to activate.
  5. Battery check button

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (16)

Accessing and Replacing the Battery

  1. Unlock the battery compartment by rotating the cap counterclockwise until the collar and cap are removed.
  2. Insert one or two 9-volt alkaline batteries into the battery terminals. Observe and match the + position.
  3. Secure the battery compartment by rotating clockwise until tightened.
  4. Test power to the NODE-BT by pressing the battery check button on the front of the controller. Observe and check for the illuminated green LED. If the LED is red, the battery needs a replacement.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (15)

Connecting DC-Latching Solenoids

  1. Attach the black leads from each solenoid to the single common wire (black lead) coming from the NODE-BT. Secure all wire connections with waterproof connectors.
  2. Attach one red wire from each solenoid to the corresponding station wire (red lead) from the NODE-BT. The station numbers are identified underneath the red wires of the NODE-BT. Secure all wire connections with waterproof connectors.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (15)

Connecting Weather Sensor

  1. Cut the yellow wire loop attached to the NODE-BT at approximately the middle of the loop.
  2. Remove approximately 1/2″ (1.3 cm) of insulation from each wire. Attach one yellow wire to each of the wires of the weather sensor. You can mount the sensor up to 100′ (30 m) from NODE-BT using 18 AWG (1 mm2) minimum wire size. Secure all wire connections with waterproof connectors.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (13)

Connecting Soil Moisture Probe

  1. Use the Hunter Soil Moisture Sensor (SC-PROBE) for soil moisture sensing.
  2. Cut the clear waterproof seal on the two gray wires connected to NODE-BT.
  3.  Remove approximately ½” (1.3 cm) of insulation from each wire. Attach each gray wire to the soil sensor probe. You can mount the soil sensor up to 100′ (30 m) from the NODE-BT using 18 AWG (1 mm2) minimum wire size. Secure wire connections with waterproof connectors.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (12)

Mounting the Controller to Solenoid Valve

NODE-BT can easily be mounted on any Hunter valve using the included tray holder. A protective rubber cover is provided to prevent dirt from accumulating on the face of the controller.

  1. Screw the Hunter DC-latching solenoid (P/N 458200) into the valve bonnet.
  2. Set the small open end of the tray holder on top of the solenoid.
  3.  Insert NODE-BT Controller into the large open end of the holder.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (11)

App Programming

  • Download the free Hunter NODE-BT App to a smartphone device from the iTunes® Store for iOS® devices or the Google Play™ store for Android™ devices.
  • Requires iOS 9.0 or later. Compatible with iPhone®, iPad®, and iPod touch® devices. Requires Android 5.0 or above.
  1. Be in range of the controller.
  2. Turn on Bluetooth on the smartphone device.
  3.  Press the SCAN button and connect to a NODE-BT Controller

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (9)

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (9)

Irrigation Schedules

Send full irrigation schedules to the controller by pressing the Schedule icon on the bottom tray and clicking the pencil icon to edit the program.

  1. Programs: Use up to three programs (A, B, or C) for irrigation.
  2. Water Days: Select specific days to water or interval days from 1 to 31 with days remaining or odd/even days. Confirm and Save.
  3.  Start Times: Set START TIME 1 and optional START TIME 2 through 8. Confirm and Save.
  4. Run Times: Set the desired RUN TIME from 1 second to 12 hours. Confirm and Save.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (8)

Controller Settings

  • Rain Sensor: Turn On to suspend automatic irrigation. Rain or Click sensor required.
  • Click-Delay: Suspends irrigation after a rain event up to 7 days.
  •  Soil Moisture Sensor:
  • Set the desired level of irrigation shutdown by scrolling from 0 (very dry) to 100 (very wet). Confirm and Save.
  • The current moisture level will automatically appear. Refresh by swiping down on screen.
  • Cycle & Soak: Turn on in the Station settings. Input the amount of time the station should run and pause. Confirm and Save.
  • Programmable Days Off: Set from 1-99 days. Confirm and Save.
  • Seasonal Adjustment: Quickly adjusts run times from 0% to 300% globally or by month. Confirm and Save.
  • Delay Between Stations: Set all station delays between 10 seconds and 4 hours. Confirm and Save.
  •  Pump/Master Valve: Turn On to assign Station 1 to use as a pump or master valve for all programs. Station 1 will no longer be used for irrigation. Requires multi-station NODE-BT and normally closed master valve.
  • Set Manual Controller Run Time: Set a custom run time from 1 minute to 12 hours. Save and Confirm.
  • Factory Reset: Restores controller back to factory defaults. Enter passcode if set. Confirm.
  • Controller Off Mode: Select the System toggle to shut down controller.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (7)

Additional Settings

Select the More icon and click the first row with the default controller name to reveal the serial number, firmware version, site, and passcode.

  1. Customize your NODE-BT: Enter the nickname, set the location, and add an image. Confirm and Save.
  2. Create a Passcode: Select Turn On Passcode to protect your device. Confirm and Save.
  3. Language Preferences: The app will automatically recognize your smartphone’s language preferences and, if available, the app will translate accordingly.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (6)

Resetting the Controller
To restore controller to the factory defaults:

  1. Remove the controller batteries .
  2.  Wait one minute .
  3. Press and hold Battery Check Button HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (5)while reinserting the batteries until Battery Check LED turns amber.

Note:
Restoring factory defaults will permanently erase schedule and settings.

Find more helpful information about your product, including installation tips, controller programming, and more.

CHALLENGE CAUSE SOLUTION
Controller not appearing in scan list or loses connection Out of Bluetooth range Move in plain view of controller.
Dead battery Replace batteries (1 or 2 9V alkaline batteries).
Visible controller, but cannot connect or stay connected; receives Errors Low battery Cycle controller batteries.
Incompatible smartphone •      Reboot smartphone.•      Reinstall Hunter NODE-BT App.•      Reset Phone Network Settings.•      Verify Phone and App compatibility: iOS 9.0 or above, and Android 5.0 or above
Manual button press not responding Dead battery Replace batteries (1 or 2 9V alkaline batteries).
App shows running, but no watering No water pressure Turn on main system water supply.
Faulty or incompatible solenoid Replace solenoid. (Must use Hunter DC latching solenoid (P/N 458200) or other compatible DC latching solenoid.)
Connected to wrong device Reconnect to controller.
Controller turns on, then off Used AC Solenoid Must use DC-Latching Solenoid.
Automatic irrigation does not start at start time NODE-BT in System Off mode Verify that NODE-BT is programmed for automatic watering.
AM/PM or 24-hour start time not set correctly Correct AM/PM or 24-hour start time.
Water days not set correctly Correct water days
Cycle and Soak is enabled Disable Sensors or Station settings.
Sensor Alarm is detected (Soil sensor, Click-Delay, or Rain/Click sensor)
Controller repeats cycles NODE-BT has more than one start time assigned to it. Each station has up to eight start times for each of the three programs. Eliminate device start times as needed.
Cycle and Soak waters in intervals Correct the Cycle and Soak Times in Station settings.
Change to incorrect app passcode Forgot passcode Remove controller batteries Wait one minute Press and hold Stop Station Button  while
reinserting the batteries until Battery Check LED turns amber.•      Create new passcode in NODE-BT App.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by taking one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  •  Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that of which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Hunter Industries could void the user’s authority to operate this device. If necessary, consult a representative of Hunter Industries Inc. or an experienced radio/television technician for additional suggestions. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Contains FC ID: QOQBGM13P

CE Notice

  • Hereby, Hunter Industries declares that the radio equipment type models NODE-BT-100, NODE-BT-100-LS, NODE-BT-100-VALVE, NODE-BT-100-VALVE-B, NODE-BT-200, and NODE-BT-400 are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
    https://assets.hunterindustries.com/portals/poa4faex/ComplianceDeclarationofConformity
  • HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (3)This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
  • Please dispose of used batteries properly, following local regulations. Do NOT incinerate.
  • Frequency band of operation: 2,400 m Hz to 2,480 m Hz
  • Bluetooth: Maximum transit power less than 20 dBm EIRP
  • Bluetooth Low Energy: Maximum power spectral density less than 10 dBm/MHz EIRPHUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (4)

Helping our customers succeed is what drives us. While our passion for innovation and engineering is built into everything we do, it is our commitment to exceptional support that we hope will keep you in the Hunter family of customers for years to come.

HUNTER-NODE-BT-Bluetooth-Enabled-Battery-Operated-Controller (2)

Documents / Resources

PDF thumbnailNODE-BT Bluetooth Enabled Battery Operated Controller
User Guide · NODE-BT Bluetooth Enabled Battery Operated Controller, NODE-BT, Bluetooth Enabled Battery Operated Controller, Bluetooth Enabled Battery Operated Controller, Enabled Battery Operated Controller, Battery Operated Controller, Operated Controller, Controller

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Hunter BT node station 3 will not turn off. How to turn it off?

    🇺🇸 Anonymous asks Hunter BT node station 3 will not turn off. How to turn it off?
    Manuals+ clarified question
    Question

    How do I turn off station 3 on the Hunter NODE-BT controller?

    Answer

    To turn off an active station on the Hunter NODE-BT controller, you can use the physical buttons on the device or the mobile app:

    • Manual Stop (On Device): Press and hold the Stop button (indicated by a square icon, labeled as button 3 in the manual) to stop the active station.
    • Using the App: Open the Hunter NODE-BT app on your smartphone, connect to your controller, and use the dashboard to stop the irrigation.
    • Controller Off Mode: In the app settings, you can select the System toggle to shut down the controller entirely if needed.

    If the station continues to run even after being turned off at the controller, there may be a mechanical issue with the valve or solenoid. Ensure you are using a DC-latching solenoid (P/N 458200), as standard AC solenoids are incompatible and may cause operation issues.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.