Hunkstar P3 AOSP Projector User Manual

Please use the projector carefully, dropping or crashing may damage parts or result in blurred images and abnormal displaying. Power
Be careful while using the power cord, avoid excessive bending; the damage of power cable may cause electric shock and fire.

It is better to unplug the power cord after power off.

Cleaning

Unplug the power cable firstly.
Clean the shell regularly with a damp cloth, neutral detergent can be used.

Please use a glasses cloth or lens paper, not to scratch the lens.
Please clean projector’s vents and speakers regularly by banister brush, or the ventilation will be blocked.

High Temperature Attention

While projection or just finishing, the exhaust port nearby will be very hot, if touch it, would get scald

While projection, please do not look the lens directly, or may hurt eyes.

Warm Tips

Do not disassemble the projector, if not, there will be a risk of electric shock, and the disassembling affect the normal warranty.
Please do not put any liquid or heavy stuff on the projector.

To ensure the stability of heat dissipation, please open the height bracket in the bottom of the projector before starting.

Package List

Projector x 1

Remote Control x 1
Power Cable x 1

User Manual x 1
Lens Cap × 1

Projector Knowledge

Projector can input high-definition video signal and composite video signal, and support stereo audio signal input and output. Please refer to the following figure to connect the projector and other audio equipment according to your own needs.

Lens
Height Adjustment Mechanism

IR Receiver
Autofocus Signal Window

Air Outlet
Power Port

Air Inlet with Removable Dust Filter
RJ45 Port
USB Port
HDMI Port 1
HDMI Port 2
AV Port
Headphone Jack
IR Receiver
Left Speaker
Right Speaker

Projector Knowledge

Keys
Label
Rubber Feet
1/4″ Screw Hole for Bracket Mount

Source Key

Arrow Keys
Power Key
Return Key

Confirm Key

Remote Control

Signal Indicator

Power Key
Arrow Keys
Home Key

Return Key
Volume Up
Volume Down

Source Key
Confirm Key
Menu

Mute Key
Focus+
Focus-

Screen Rotation

Projector Knowledge

Standard Setting
Please refer to the following table to adjust your picture size and distance.

Please allow + 3% to the image sizes in the table above. If the distance is outside the specified range, the image could be blurry.

Warning:
Please check the diagram below for the trapezoid adjustment.

Remote Control

Installation Method
Contact a professional installer to mount this projector to a ceiling. Follow the instructions below for the correct projector positions. (from the lens to the screen).

Warning:

The projector may be damaged beyond repair if it is incorrectly mounted on a ceiling or on a surface
The projector should only be used in an environment where the temperature does not exceed the range of 5°C-35°C. Projector malfunction may occur if this is not adhered to.
Malfunction may occur if the projector is subjected to dusty, wet, moist or smoky conditions.

Poor ventilation could cause overheating which could lead to damage to the projector as well as a life threatening situation.

Turn the Projector Operation On/Off

When the projector is connected to a power source, the projector enters standby and the cover signal indicator is red.

Operation on: Press the power key on the body or the power key on the remote control, the indicator will turn blue and enter the working state.
Operation off: In the working state, press the power key of the body or the power key on the remote control, the indicator changes from blue to red, and the projector is turned off.

Use of the Projector

When the newly installed projector is used for the first time, the image will be blurred, and it is necessary to focus the picture;

When the picture is blurred, press the focus keys “F+” and” F- “on the remote control to adjust the focal length of the lens. Tap or long press the focus button until the picture is clear. (As shown below)
(Auto focus function is only available in autofocus version. Please do not block the camera while autofocusing.)

How to Use Projection Settings
Select “SETTING” on the main interface, after entering setting, select the mode you want in the projection settings.
Projection mode: Front-Desktop / Rear-Desktop / Front-Ceiling / Rear-Ceiling

Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

Manual Keystone (Manually adjust the corners of the screen with the arrow keys until the screen is perfectly rectangular).

Auto Keystone upon Startup (It will display the projection screen in a square shape when the device is turned on.)

Auto Keystone upon Displacement (It will display the projection screen in a square shape even when the device is displaced.)

Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

Auto Focus upon Startup (It will focus automatically when the device is turned on.)

Auto Focus upon Displacement (It will focus automatically even when the device is displaced.)

Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

Digital Zoom (Zoom out or enlarge the image)

How to Select the Source

Press the signal source button on the remote control, select the source channel you want to input in the pop-up window, such as HDMI 1/HDMI 2/AV, and then press the “OK” button on the remote control to enter the corresponding source interface.

Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

How to Connect to WiFi

Enter the “Settings” interface and select “Network”.
From there, select “WiFi Setting” and choose the desired WiFi network.
Enter the password and complete the connection. Once connected, it will display “Connected”.

How to Connect Bluetooth Enter the “Settings” interface and select “Bluetooth”. From there, enable the Bluetooth function, search for your Bluetooth device and pair it with your Bluetooth device.