M5Stack C6LoRA Module User Manual

M5Stamp C6LORA
Model: Stamp C6LoRA
Manyèl itilizatè

Deskripsyon

Stamp C6LoRa is a high-performance programmable LoRa module designed for the 830 ~ 930 MHz frequency range. The module features an ESP32-C6 SoC, an SX1262 LoRa RF transceiver, and an LNA signal amplifier chip. It comes with two onboard IPEX antenna connectors for external Wi-Fi and LoRa antennas, respectively.
At its core, the ESP32-C6 integrates a rich set of peripheral interfaces, enabling extended functionality through secondary development. It also supports 2.4GHz Wi-Fi 6, offering broader possibilities for IoT applications. Additionally, the module includes a  PI4IOE5V6408 IO expander chip, which is used for LoRa transceiver circuit control and amplifier enable signal management, delivering enhanced power efficiency and providing additional usable IO resources.
A built-in DC-DC converter supports a DC input range of 3.7 to 5V and allows for lithium battery power, making it adaptable to various hardware deployment scenarios. The module is well-suited for long-range communication applications such as smart irrigation, remote metering, and power equipment control.

Espesifikasyon

Quick Start

3.1 Preparasyon

1. Vizite sit ofisyèl Arduino a websit la epi enstale Arduino IDE a
   https://www.arduino.cc/en/Main/Software
2. Ajoute Manadjè Konsèy Administrasyon sa a URL pou File → Preferans → Manadjè Tablo Siplemantè URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Louvri Manadjè Komisyon Konsèy yo, chèche "ESP32", epi klike sou enstale.
4. After installation, select the board “ESP32C6 Dev Module.”
5. Configure the following options. USB CDC On Boot: “Enabled”

3.2 Wi-Fi Test
Chwazi ansyen anamppwogram "Ex" laamples” → “WiFi” → “WiFiScan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
After uploading is complete, open the Serial Monitor to view Enfòmasyon sou eskanè Wi-Fi.

3.3 BLE Scan
Chwazi ansyen anamppwogram "Ex" laamples” → “BLE” → ”Scan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
After uploading is complete, open the Serial Monitor to view Enfòmasyon sou eskanè BLE.

3.4 LoRa TX
After burning the LoRa test firmware, check the LoRa transceiver information via the ESP32-C6 USB CDC serial port.

Avètisman FCC

Atansyon FCC:
Nenpòt Chanjman oswa modifikasyon pati ki responsab pou konfòmite pa apwouve ekspreseman kapab anile otorite itilizatè a pou opere ekipman an.
Aparèy sa a konfòm ak pati 15 Règ FCC yo. Operasyon an sijè a de kondisyon sa yo: (1) Aparèy sa a pa ka lakòz entèferans danjere, epi (2) aparèy sa a dwe aksepte nenpòt entèferans resevwa, enkli entèferans ki ka lakòz operasyon endezirab.

REMAK ENPÒTAN:
Nòt: Yo te teste ekipman sa a epi yo jwenn li konfòme yo ak limit pou yon aparèy dijital Klas B, dapre pati 15 Règ FCC yo. Limit sa yo fèt pou bay pwoteksyon rezonab kont entèferans danjere nan yon enstalasyon rezidansyèl. Ekipman sa a jenere, itilize, epi yo ka gaye enèji frekans radyo epi, si li pa enstale ak itilize an akò ak enstriksyon yo, ka lakòz entèferans danjere nan kominikasyon radyo. Sepandan, pa gen okenn garanti ke entèferans pa pral rive nan yon enstalasyon an patikilye. Si ekipman sa a lakòz entèferans danjere nan resepsyon radyo oswa televizyon, sa ki ka detèmine pa fèmen ekipman an epi limen, itilizatè a ankouraje pou eseye korije entèferans lan pa youn oswa plis nan mezi sa yo:

• Reoryantasyon oswa deplase antèn k ap resevwa a.
• Ogmante separasyon ki genyen ant ekipman ak reseptè a.
• Konekte ekipman an nan yon priz sou yon sikwi diferan de sa ki reseptè a konekte.
• Konsilte konsesyonè a oswa yon teknisyen radyo/televizyon ki gen eksperyans pou èd.

Deklarasyon FCC Ekspozisyon Radyasyon: Ekipman sa a konfòme li avèk limit ekspozisyon FCC radyasyon ki tabli pou yon anviwònman san kontwòl.

Nòt enpòtan:
Nan ka kondisyon sa yo pa ka satisfè (pa egzanpamppa egzanp, sèten konfigirasyon laptop oswa ko-lokasyon ak yon lòt transmetè), otorizasyon FCC a pa konsidere kòm valab ankò, epi yo pa ka itilize ID FCC a sou pwodwi final la. Nan sikonstans sa yo, entegratè OEM lan pral responsab pou re-evalye pwodwi final la (ki gen ladan transmetè a) epi jwenn yon otorizasyon FCC apa.

Fen pwodwi etikèt
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

Enfòmasyon manyèl pou itilizatè final la
Entegratè OEM la dwe konnen pou pa bay itilizatè fen enfòmasyon sou fason pou enstale oswa retire modil RF sa a nan manyèl itilizatè a nan pwodwi final ki entegre modil sa a.
Manyèl itilizatè final la dwe genyen tout enfòmasyon/avètisman ki obligatwa yo jan yo montre nan manyèl sa a.

Enstriksyon entegrasyon pou manifaktirè pwodwi lame yo dapre KDB 996369 D03 OEM Manual v01

2.2 Lis règ FCC ki aplikab yo
CFR 47 FCC PATI 15 SOUPART C yo te envestige. Li aplikab pou transmetè modilè a.

2.3 Kondisyon espesifik itilizasyon operasyonèl
Modil sa a se yon modil endepandan. Si pwodwi final la pral enplike plizyè kondisyon transmisyon an menm tan oswa diferan kondisyon operasyonèl pou yon transmetè modilè endepandan nan yon òdinatè prensipal, manifakti òdinatè prensipal la dwe konsilte ak manifakti modil la pou metòd enstalasyon an nan sistèm final la.

2.4 Pwosedi modil limite
Pa aplikab

2.5 Trase desen antèn
Pa aplikab

2.6 Konsiderasyon ekspoze RF
The device has been evaluated to meet the general RF exposure requirements. The device can be used in mobile or fixed exposure conditions with a minimum distance of 20 cm between the radiator & user’s body.

2.7 antèn
This radio transmitter has been approved by the Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

2.8 Mete etikèt sou ak enfòmasyon sou konfòmite
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

2.9 Enfòmasyon sou mòd tès ak egzijans tès adisyonèl
The host manufacturer that installs this module with limited modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result complies with FCC part 15.247 and 15.209 requirements, then the host can be sold legally.

Enstriksyon entegrasyon pou manifaktirè pwodwi lame dapre KDB 996369 D03 OEM Manyèl v01

2.10 Tès adisyonèl, Pati 15 Souspati B Limit responsabilite nou
This transmitter module is tested as a subsystem, and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rule requirements if applicable.

2.11 Remake Konsiderasyon EMI
We recommend using “best practice” RF design engineering, testing, and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. The host manufacturer is responsible for ensuring compliance with the applicable FCC rules for the transmitters operating individually and simultaneously. This includes compliance for the summation of all emissions from all outputs occupying the same or overlapping frequency ranges, as defined by the applicable rules.

2.12 Kijan pou fè chanjman – Nòt enpòtan
Nan ka kondisyon sa yo pa ka satisfè (pa egzanpample, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, OEM integrator contacts Grantees to make permissive changes, or the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Osi lontan ke tout kondisyon ki anwo yo satisfè, plis tès transmetè yo pa pral obligatwa. Sepandan, entegratè OEM la toujou responsab pou teste pwodwi final yo pou nenpòt lòt kondisyon konfòmite ki nesesè ak modil sa a enstale.