DIRECTV RC66RX IR/RF Remote Control User Manual

Entwodiksyon

This manual provides instructions for the DIRECTV RC66RX IR/RF Remote Control. This remote is designed to operate most DirecTV receivers in both Infrared (IR) and Radio Frequency (RF) modes. The RF feature allows control of the receiver without direct line-of-sight. It is compatible with various DirecTV receiver models including R16, R22, H21, H22, H23, H24, HR21, HR22, HR23, HR24, HR34, and C31. Two AA batteries are included with the remote for immediate use.

Figure 1: Two DIRECTV RC66RX Remote Controls with Batteries

Enstalasyon

1. Enstalasyon batri

1. Jwenn kouvèti lòj batri a sou do kontwòl remote la.
2. Glise kouvèti a anba pou ouvri konpatiman an.
3. Mete de pil AA, asire w ke tèminal pozitif (+) ak negatif (-) yo aliyen ak endikatè ki anndan konpatiman an.
4. Glise kouvèti konpatiman batri a tounen nan plas li jiskaske li fè yon klik byen fèm.

Figure 2: Battery Compartment of the RC66RX Remote

2. Programming for DirecTV Receiver

The RC66RX remote is typically pre-programmed to control your DirecTV receiver. If it does not respond, ensure the remote is set to the correct mode (usually 'DIRECTV' or 'SAT' if applicable, though this model primarily functions for DirecTV). For RF mode, your receiver must be compatible (R16, R22, H21, H22, H23, H24, HR21, HR22, HR23, HR24, HR34, C31). Refer to your DirecTV receiver's manual for specific RF pairing instructions if needed.

3. Programming for TV and Other Devices (IR Mode)

To control your television or other devices (e.g., AV receiver) with the RC66RX remote, you will need to program it using IR codes. This allows the remote to control functions like TV power, volume, and input.

1. Locate the mode switch at the top of the remote. Slide it to the 'TV' position.
2. Press and hold the 'MUTE' and 'SELECT' buttons simultaneously until the green light at the top of the remote blinks twice.
3. Enter the 5-digit programming code for your TV brand. You can find these codes in your DirecTV receiver's user manual or on the DirecTV support websit.
4. Point the remote at your TV and press the 'PWR' button. If the TV turns off, the code is correct.
5. If the TV does not turn off, repeat steps 2-4 with the next code for your TV brand.
6. Once the TV is programmed, slide the mode switch back to the 'DIRECTV' position to control your receiver.

Figure 3: Top Section of the RC66RX Remote with Mode Switch

Enstriksyon Operasyon

The DIRECTV RC66RX remote control features a comprehensive layout for easy navigation and control of your entertainment system.

Figure 4: Full Button Layout of the RC66RX Remote

Fonksyon bouton kle yo:

• ANTRE TELEVIZYON: Cycles through available video inputs on your television.
• PWR (pouvwa): Turns the DirecTV receiver on or off.
• ON/OFF (&TV Power): Turns the programmed television on or off.
• FÒMA: Chanje rapò aspè ekran an.
• Playback Controls (Play, Pause, Stop, Rewind, Fast Forward, Skip): Controls media playback on your DirecTV receiver.
• ANREJISTREMAN (Anrejistreman): Li kòmanse anrejistreman pwogram aktyèl la.
• GID: Montre gid pwogram lan.
• AKTIF: Accesses the DirecTV Active channel for interactive services.
• LIS: Montre lis pwogram ou anrejistre yo.
• Sòti: Sòti nan meni oswa ekran aktyèl la.
• Tounen: Retounen nan ekran oswa meni anvan an.
• MENI: Accesses the main DirecTV menu.
• ENFO: Montre enfòmasyon sou pwogram aktyèl la.
• SELECT (Center Button): Konfime seleksyon yo nan meni yo.
• Bouton flèch: Navige nan meni ak chanèl yo.
• VOL (+/-): Adjusts the volume of the programmed television.
• Bèbè: Mutes the television audio.
• PAJ CHAN (Monte/Desann): Changes channels or pages through the guide.
• PREV: Retounen nan anvan an viewed chanèl.
• Klavye Nimerik (0-9, TIRÈ, ANTRE): Antre nimewo chanèl yo dirèkteman.
• Bouton ki gen koulè (wouj, vèt, jòn, ble): Used for special functions within certain menus or applications.

IR vs. RF Mode

The RC66RX remote supports both Infrared (IR) and Radio Frequency (RF) modes. IR mode requires a direct line of sight between the remote and the device being controlled. RF mode uses radio waves, allowing you to control your DirecTV receiver without pointing the remote directly at it, even if the receiver is in a cabinet or another room (within range). Ensure your DirecTV receiver is RF-compatible for this feature to work.

Antretyen

Ranplasman batri

When the remote's performance degrades or it stops responding, it is likely time to replace the batteries. Follow the battery installation steps in the Setup section to replace the two AA batteries.

Netwayaj

To clean your remote control, use a soft, dry cloth. For stubborn dirt, lightly dampRense twal la avèk dlo oswa yon pwodui netwayaj dou ki pa abrazif. Evite itilize pwodui chimik ki agresif oswa imidite twòp, paske sa ka domaje elektwonik telekòmand lan.

Depanaj

• Remote pa reponn: Check if the batteries are correctly inserted and have sufficient charge. Replace batteries if necessary. Ensure the mode switch is set to the correct device (e.g., 'DIRECTV' for receiver functions).
• TV not responding to power/volume: Verify that the remote has been correctly programmed for your television using the IR programming steps. Ensure the mode switch is set to 'TV' when attempting to control TV functions.
• Buttons sticking or unresponsive: This may indicate dirt or debris under the buttons. Gently clean the remote as described in the Maintenance section. If the issue persists, the remote may need replacement.
• RF mode not working: Confirm your DirecTV receiver model is listed as RF compatible (R16, R22, H21, H22, H23, H24, HR21, HR22, HR23, HR24, HR34, C31). Ensure there are no major obstructions blocking the RF signal, although line-of-sight is not strictly required, extreme interference can affect performance.

Espesifikasyon

Garanti ak sipò

For warranty information and customer support, please refer to the documentation provided with your purchase or contact SatelliteSale customer service directly. Keep your proof of purchase for any warranty claims.