VEVOR Dent Repair Machine (GYSpot 2700/2600)

1. Entwodiksyon

This manual provides detailed instructions for the safe and effective operation and maintenance of your VEVOR Dent Repair Machine, models GYSpot 2700 and GYSpot 2600. This versatile spot welder and dent puller is designed for professional vehicle panel repair, offering efficient solutions for various metal deformations.

2. Enstriksyon Sekirite

WARNING: Always read and understand all safety warnings and instructions before operating this equipment. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

• Ensure the machine is connected to a properly grounded power source.
• Mete ekipman pwoteksyon pèsonèl (PPE) ki apwopriye, tankou kas soude, gan, ak rad pwoteksyon.
• Pa opere machin nan nan damp oswa kondisyon mouye.
• Kenbe timoun yo ak pèsonèl ki pa otorize lwen zòn travay la.
• Ensure adequate ventilation to avoid inhaling fumes.
• Disconnect power before performing any maintenance or changing accessories.
• Avoid direct contact with live electrical parts.
• Do not use the machine for purposes other than its intended use.

3. Package Contents & Components

Your VEVOR Dent Repair Machine comes with a comprehensive set of accessories to facilitate various repair tasks.

Pwodwi pou Telefòn enkli:

• Dent Puller Machine (GYSpot 2700 or GYSpot 2600)
• Zam soudi
• Dent Puller (Slide Hammer)
• Konektè
• Manual Suction Cup
• Carbon Rods
• Wavy Line Wire
• Draw Hook
• Carbon Rod Chuck
• Round Meson
• Meson Chuck
• Triangular Meson
• Spot Welding Head
• OT Meson
• Kle
• Six Claw Hook
• Accessory Kit Storage Box

4. Enstalasyon

1. Konekte fil tè: Attach the ground wire to the designated terminal on the machine. Ensure a secure connection to the vehicle's metal body, away from the repair area.

   For first-time use, the machine can polish off the galvanized layer on the grounding head, or connect the ground several times to allow the galvanized layer to come off naturally.

2. Connect Sheet Metal Gun: Attach the sheet metal gun to its designated port on the machine.

3. Pouvwa sou: Turn the power switch clockwise to boot the machine. Continue turning clockwise to increase power as needed.

5. Operasyon Enstriksyon

The VEVOR Dent Repair Machine offers multiple welding modes and functions for various dent repair scenarios.

5.1 Kontwòl Panel Overview

1. Triangular Meson Pull
2. Round Meson Pull
3. OT Meson Pull
4. Wave Line Welding
5. Carbon Rod to Close the Fire (Heating)
6. Power Switch & Regulation Knob
7. Manyèl / Otomatik Chanjman
8. Error Indication Light
9. Limyè Endikatè pouvwa

Use the Power Switch & Regulation Knob (6) to adjust the power. The Manual/Automatic Switch (7) allows you to select between manual and automatic operation modes. Carbon rod heating is typically performed in manual mode.

5.2 Dent Pulling with Slide Hammer

For general dent pulling, attach the slide hammer to the welding gun. Spot weld the tip to the center of the dent, then use the slide hammer to pull the dent out.

5.3 Welding Pulling Rings

For larger or more complex dents, pulling rings can be welded onto the car body. Insert the pulling ring into the welding gun's chuck, place it on the dented area, and activate the weld. Repeat for multiple rings as needed, then use a puller bar with hooks to extract the dent.

5.4 Welding Wavy Wire

For curved areas or long, narrow dents, wavy wire can be used. Select the wavy wire welding mode on the control panel. Place the wavy wire along the dent and spot weld it in sections. Once welded, use a pulling tool to straighten the panel.

5.5 Carbon Rod Heating (Shrinking)

To shrink stretched metal or finish a repair, use the carbon rod heating function. Select the carbon rod mode, insert a carbon rod into the welding gun, and apply heat to the desired area to shrink the steel sheet.

6. Antretyen

• Netwayaj: Regularly clean the machine and accessories, especially the welding gun tips and ground clamp, to ensure optimal conductivity and performance.
• Enspeksyon: Periodically inspect all cables, connections, and accessories for wear, damage, or loose fittings. Replace any damaged parts immediately.
• Sistèm refwadisman: Ensure the side vents are clear of obstructions to allow for efficient heat dissipation.
• Depo: Store the machine and accessories in a dry, clean, and secure location when not in use. Use the provided compact toolbox for organizing accessories.

NAN. Depanaj

8. Espesifikasyon

GYSpot 2700

• Model: GYS2700
• Koulè: jòn
• Max Output Current: 3500A
• Antre Voltage: 220V
• Pouvwa Antre: 2KW
• Input Current Fuse: 16A
• Work Model: 5 Modes Available
• Single Side Welding Thickness: 0.02 - 0.05 in / 0.6 - 1.2 mm
• Dimensions (L x W x H): 8" x 12.5" x 10" / 20.5 x 32 x 25.5 cm
• Pwa: 53.8 lbs / 24.4 kg

GYSpot 2600

• Model: GYS2600
• Max Output Current: 3500A
• Antre Voltage: 220V
• Frekans: 60Hz
• Pouvwa Antre: 2KW
• Input Current Fuse: 16A
• Work Model: 5 Modes Available
• Single Side Welding Thickness: 0.02 - 0.05 in / 0.6 - 1.2 mm
• Dimensions (L x W x H): 8" x 12.5" x 10" / 20.5 x 32 x 25.5 cm
• Pwa: 53.8 lbs / 24.4 kg

9. Konsèy itilizatè yo

• Diferans modèl: The primary difference between the GYS2700 and GYS2600 models lies in their current output, with the GYS2700 having a current of 2700 and the GYS2600 having a current of 2600. Both models share many core features and accessories.
• Preparasyon sifas: Always ensure the metal surface is clean and free of paint, rust, or grease before welding for optimal adhesion and repair quality.
• Pratike: If you are new to dent repair, practice on scrap metal to get a feel for the machine's settings and techniques before working on your vehicle.

10. Garanti & Sipò

VEVOR provides a one-year warranty for this product. For any after-sales problems or technical support, please contact VEVOR customer service. Ensure you have your purchase details and model number ready when contacting support.

VEVOR is dedicated to providing tough equipment & tools at incredibly low prices, backed by 24/7 attentive service.