Read all instructions carefully before operating the VEVOR 1200W Foam Machine. Failure to follow these instructions may result in electric shock, fire, or serious injury.
Električna sigurnost: Ensure the power source matches the machine's requirements (AC100V-120V, 50-/60HZ). Use a grounded outlet and avoid using damaged power cords. Keep all electrical connections away from water and foam.
Water and Foam: Use only approved foam powder. Do not ingest foam solution. Avoid direct contact with eyes. If foam gets into eyes, rinse immediately with water.
Plasman: Place the foam machine on a stable, level surface. Ensure adequate ventilation around the machine. Keep children and pets away from the machine during operation.
Operacija: Do not operate the machine if any part is damaged. Do not attempt to modify the machine. Always supervise children during foam activities.
Skladištenje: Stroj čuvajte na suhom i hladnom mjestu kada se ne koristi.
2. Sadržaj paketa
Your VEVOR 1200W Foam Machine package includes the following items:
1 x Foam Machine (1200W)
1 x Submersible Pump
1 x Hose (90.55 in / 2.3 m)
1 x Rotating U-Shaped Bracket (9.45 in x 10.24 in / 240 x 260 mm)
1 x 20 Gallon / 75.71 L Water Tank
3 x Foam Powder (1.1 lbs / pack / 500 g / pack)
1 x Stalak za tronožac
1 x Power Cord (102.36 in / 2.6 m)
3 x Round Fixing Screws
2 x podloške
1 x korisnički priručnik
Image: All included components of the VEVOR 1200W Foam Machine, including the main unit, tripod, water tank, pump, hoses, foam powder, and power cord, with key dimensions.
3. Upute za postavljanje
Sastavite stalak za stativ: Connect the tripod stand components securely using the provided screws and washers. Ensure the stand is stable on a flat surface.
Mount the Foam Machine: Attach the VEVOR foam machine to the assembled tripod stand using the rotating U-shaped bracket. Secure it firmly. The machine can be adjusted for spray angle.
Connect the Submersible Pump:Image: The green submersible pump with its hose connected to the main foam machine unit.Place the submersible pump into the 20-gallon water tank. Connect the hose from the pump to the inlet on the foam machine. Ensure all connections are tight to prevent leaks.
Prepare Foam Solution:Image: Three packs of foam powder next to the 20-gallon water tank, illustrating the preparation of the foam solution.Fill the 20-gallon water tank with water. Add one pack of VEVOR foam powder to the water. Stir the solution thoroughly for 3-5 minutes until the powder is fully dissolved. The recommended ratio is 1:80 (foam powder to water).
Priključak za napajanje: Connect the foam machine's power cord to a suitable grounded electrical outlet. Ensure the power switch on the machine is in the OFF position before plugging it in.
Image: Visual representation of the foam machine's secure, waterproof power connections, fan duct, and water pump with dry-run overheat control. A reminder notes the 15-second delay for foam dispensing and fan shutdown.
Setup Video: VEVOR Foam Machine Unboxing and Assembly
Video Description: This video provides a detailed unboxing and assembly guide for the VEVOR Foam Machine, demonstrating how to set up all components for an epic foam party. It highlights the ease of assembly and the various parts included in the package.
4. Upute za rad
Uključivanje: Once the foam solution is prepared and all connections are secure, switch the main power button on the foam machine to the ON position. The fan will start, and foam will begin to generate after a short delay (approximately 15 seconds).
Podesite kut prskanja: Use the adjustable bracket to tilt the foam machine up or down to achieve the desired foam distribution and effect.
Kontinuirani rad: The VEVOR foam machine is designed for continuous use thanks to its temperature management system in the pump, preventing overheating. The large 20-gallon tank and concentrated foam powder ensure long-lasting foam production.
Monitor Foam Solution: Periodically check the foam solution level in the water tank. Refill with pre-mixed solution as needed to maintain continuous foam output.
Isključivanje: To stop operation, switch the main power button to the OFF position. The fan will continue to run for approximately 15 seconds to clear any remaining foam.
Image: The VEVOR 1200W Foam Machine actively producing a high volume of foam, creating a foam-filled environment for an outdoor event.Image: Demonstrates how to adjust the foam machine's spray head to different angles (tilted up, slightly tilted, and adjusted up/down) to create aerial bubble shows, joyful bubble baths, or bubble battle fun.
Foam Powder Usage Video
Video Description: This video demonstrates the effectiveness of foam powder packs in creating abundant foam for parties. It shows the foam machine in action, producing a large volume of foam from the mixed solution.
5. Održavanje
Čišćenje: After each use, rinse the foam machine, submersible pump, hoses, and water tank thoroughly with clean water to remove any foam residue. This prevents clogging and extends the lifespan of the components.
Sušenje: Prije skladištenja ostavite sve komponente da se potpuno osuše na zraku.
Skladištenje: Disassemble the machine and store it in its original packaging or a suitable container in a dry, cool place, away from direct sunlight and extreme temperatures. The compact design allows for easy storage.
Vodootporni dizajn: The machine features a waterproof fan with complete protective sealing and a pump with a temperature management system, designed to prevent water damage and overheating during extended use.
6. Rješavanje problema
Problem
Mogući uzrok
Otopina
No foam output
Napajanje nije spojeno ili uključeno.
Foam solution not mixed correctly or empty.
Hose or pump clogged.
Check power connections and ensure switches are ON.
Verify foam solution is properly mixed and sufficient.
Inspect and clear any blockages in the hose or pump.
Low foam output
Insufficient foam powder in solution.
Razina vode je preniska.
Partial clog in hose or pump.
Add more foam powder to the solution.
Provjerite je li spremnik za vodu dovoljno napunjen.
Check for partial clogs and clean components.
Stroj se pregrijava
Extended continuous operation without proper ventilation.
Pumpa radi na suho.
Ensure adequate airflow around the machine.
Check water level in the tank; the pump has a temperature management system to prevent overheating, but continuous dry running should be avoided.
7. Specifikacije
Značajka
Specifikacija
Broj modela
LM-1000
Nazivna snaga
1200 W
Radna svtage
120V / 60Hz
Težina artikla
33 funti / 13.5 kg
Dimenzije proizvoda
18.5 cm D x 21.26 cm Š x 39.37 cm V
Materijal
Legirani čelik
Boja
Žuta boja
Kapacitet spremnika za vodu
20 Gallons / 75.71 L
8. Jamstvo i podrška
The product information indicates that there is no specific warranty description provided. For any product-related inquiries, technical support, or warranty claims, please refer to the official VEVOR webweb-mjesto ili izravno kontaktirajte njihovu korisničku službu.
VEVOR LM-ZJYT1500LED Foam Machine User Manual and Instructions Comprehensive user manual and assembly instructions for the VEVOR LM-ZJYT1500LED Foam Machine. Includes technical specifications, operation guide, maintenance tips, and safety precautions.
VEVOR LM-FJLS300 Priručnik za uporabu i upute za stroj za izradu pjene Sveobuhvatni korisnički priručnik i upute za sastavljanje stroja za izradu pjene VEVOR LM-FJLS300. Uključuje sigurnosne smjernice, tehničke specifikacije, načine rada, održavanje i savjete za rješavanje problema.
VEVOR LM-ZJYT1500LED Foam Machine User Manual and Instructions This user manual provides comprehensive instructions for the VEVOR LM-ZJYT1500LED Foam Machine, covering assembly, operation, maintenance, safety guidelines, and technical specifications. Learn how to set up and use your foam machine effectively.
