M-Cube Laser Measure
User Manual
Basic
Laser Measure
 |
Laser Measure Meeeure the distance between two points |
 |
Big Number Meesure the distance with tigger number, Designed for outdoor chrasmetances |
 |
Max Min Laser Provide Maximum. Minimum and The Average Length |
 |
Bilateral Laser Meawre distance in both ection: “Requires 03 Bilateral Module Not Included in standard Edition |
 |
1) Front Align Messure from the top of tie device |
 |
2) Back Align Measure along the bottom of the device |
 |
3) Module Back Align Meseure from the bottom of the module ‘Begutes Modute |
Pro-Laser
 |
Area Mode Measure the length of sides Aand 8B. The device wilt automatically cefaslate the sree of the top rectangle |
 |
Volume Mode moseure the height (i). and then measwre the length of tides A anc & The device wilt 060 up the total velumne of the spece |
 |
Continwes Wail Area Start by Measuring the height (11 Then, meagere the lengths of sides A. B, C. D. and 90 On. The device will sum up the tetel sroen of oll the vertical wale. |
 |
Pythagorean Height Measure the Horizertal length A. and tited tength C. Calculate the Height 1 |
 |
Indirect Pythagorean Height Measure the Tited tength B. and tHted length C. Calculate the Meight h2 |
 |
Pythagorean Length Measure the vertical length h1. and tilted length C Colcuiate the hortzontal length A |
 |
Angle Mode To cetculete the erglece of any trianglar shape, measure adjacent edge AC, then Measure the third side h1. |
Level
1) Single Axis Level
Place the device with one side facing upwerd. The product wil orter single ans level mode.
2) Dual Axis Level
Place the device with the screen facing upwerd, the product will eadich to dual axis level mode.
| Battery | 900mAh. input:SV-1A |
| Materials | ABS Plastic. PC Plastic |
| Display | 1.89′ IPS LCD Display with Tempered Glass |
| Resolution | 240ppi |
| Accuracy | ± 1/16in (± 2mm)* In Ideal Circumstances |
| Range | 164ft (50m) |
| APP | Elluetooth Connection With MEAZOR APP |
FCC warning:
- This device should be installed and operated with minimum distance Ocm between the radiator&your body.
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. - Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
4. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Documents / Resources
 |
HOZO DESIGN C00-P M-Cube Laser Measure [pdf] User Manual C00-P M-Cube Laser Measure, C00-P, M-Cube Laser Measure, Laser Measure, Measure |