Honeywell - LOGOHome
RPLS530A/RPLS531A

Applications

  1. The RPLS530A/RPLS531A switch can be used in a single-pole or 3-way installation with the following types of lighting:
    • Incandescent
    • Halogen
    • Low-voltage halogen with transformer
    • Fluorescent
    The RPLS530A/RPLS531A switch cannot be used with a load below 40 W, a load above 500 W or a motor.

Installation

  1. Cut power at the circuit breaker to avoid electric shock.
  2. Remove the existing switch. (For a 3-way installation, identify and label the wire that is connected to the “common” screw.)
  3. Install the new switch (refer to the appropriate section below).
  4. Apply power at the circuit breaker.

NOTE A:
The white wire is not the neutral wire but the wire going to the load.

SINGLE-POLE INSTALLATION

Honeywell Programmable Wall Switch - SINGLE POLE

Connect wires “2” and “C” of the RPLS530A/RPLS531A to the line (120 V) wire.
EXISTING 3-WAY INSTALLATION

Honeywell Programmable Wall Switch - EXISTING 3 WAYRPLS530A/RPLS531A

Installation and User Guide

Programmable Wall Switch

Connect wire “C” of the RPLS530A/RPLS531A to the “common” wire, identified when removing the old switch. Connect the other two RPLS530A/RPLS531A wires to the two remaining wires.
At the other 3-way switch, connect the jumper wire between the “common” screw and the screw where wire “1” of the RPLS530A/RPLS531A is connected.
NEW 3-WAY INSTALLATION  

Honeywell Programmable Wall Switch - NEW 3 WAY

The jumper wire is not required in this installation. A single-pole switch can be used as the other switch in a 3-way installation.

Power-On

Honeywell Programmable Wall Switch - Pry the switch

  1. Pry the switch door open from the bottom using a small screwdriver. Reset
  2. Ensure the ON/OFF selector is set to ON. Control (4)
  3. Reset the switch using a paper clip. 0:00 and MO will flash.

If the display is blank:

  • Ensure the ON/OFF selector is properly engaged in the ON position. Push it to the right using a small screwdriver.
    • On/Off selector
  • If the programmable switch controls a lamp equipped with a built-in On/Off switch, ensure the lamp switch is set to On.
  • Ensure the light bulb is not burned out and is tightly screwed in its socket.

EXISTING 3-WAY INSTALLATION

If either switch does not work properly, rewire the jumper between the  “common” screw and the other screw.
WARNING: Before replacing the light bulb, place the ON/OFF selector in the OFF position. Failure to do so might damage the switch.

Setting the Clock

NOTE: The switch displays the time in 24-hour format by default or following a reset.

  1. To change to a 12-hour format (or vice versa), proceed as follows:
    a) Press one of the control buttons to ensure the MAN or AUTO indicator is displayed.
    b) Press the MIN and HOUR buttons simultaneously and briefly (0:00 display = 24-hour, 12:00 display = 12-hour).
  2. Set the time using the HOUR and MIN buttons. If you have selected the 12-hour format, ensure that PM appears on the screen when an afternoon time is displayed.
  3. Set the day by using the DAY button.
  4. Press one of the control buttons or close the switch door to return to normal operation.

Selecting the Operating Mode

The programmable switch has 2 operating modes: manual (MAN) and automatic (AUTO). To switch mode, press the switch door for 3 seconds.
Manual Mode
The programmable switch operates as a regular switch.
Briefly press the switch door to turn the lights On or Off.
The mode (MAN) and state (ON or OFF) are displayed.
Honeywell Programmable Wall Switch - FIG 1Automatic Mode
The programmable switch follows the programmed schedule. The mode (AUTO), state (ON or OFF), and current program number are displayed..

Honeywell Programmable Wall Switch - FIG 2

To temporarily override the programmed schedule, press the switch door
The new state (ON or OFF) will flash to show that this state is temporary.
The override remains in effect until you press the switch door again or until the beginning of the next program.

Programming

You can set up to 7 programs. To set a program, you need to enter its start time (ON) and its end time (OFF).

  1. Pry the switch door open using a small screwdriver.
  2. Press the PGM button to display a program and its On or Off time. For example, when you first press PGM, program number 1 (P1) and its On-time (ON) will appear. -:– will appear instead of the time if the program is not set (inactive).
    Honeywell Programmable Wall Switch - FIG 3
  3. Press the DAY button to select the day to which you want to apply to the program.
    NOTE: If you want to apply the program to every day of the week, press DAY until all the days are displayed. (This still counts as 1 program, not 7)
    Honeywell Programmable Wall Switch - FIG 4
  4. Press the HOUR and MIN buttons to set the ON time (a time when you want the lights to turn on). If you have selected the 12-hour format, ensure that PM appears on the screen when an afternoon time is displayed.
  5. After you have programmed the ON time, press the PGM button to display the OFF time (a time when you want the lights to turn off).
  6. Repeat steps 3 through 5 to program the OFF time. If the program ON time is set for every day of the week, the program OFF time will automatically be set for every day.
    Honeywell Programmable Wall Switch - FIG 5
  7. To set another program, repeat steps 2 through 6. Programs that are not set will remain inactive.
  8. Press one of the control buttons or close the switch door to return to normal operation.

Clearing a Program
Press the PGM button until the desired program is selected. Hold the PGM button for 3 seconds. -:– appears when the program is erased.

Technical Specifications

Supply: 120 VAC, 50 / 60 Hz
Minimum load: 40 watts
Maximum load: 500 watts
Operating temperature range: 5°F to 122°F (-15°C to 50°C)
Storage temperature range: -4°F to 122°F (-20°C to 50°C)
Power outage: The programs are protected by a rechargeable battery.
The screen is blank during the power outage.
Certifications: CSA & UL
RPLS530A/RPLS531A

Troubleshooting

Blank display ·Verify circuit breaker at the main panel.
·Verify if the light bulb is burned out
·Ensure the ON/OFF selector is at ON.
·Reset the switch using a paper clip.
Faded or irregular display · Load is less than 40 W
· Ambient temperature is below freezing point
Cannot switch between 24-hour format and 12-hour format First, press one of the control buttons so that MAN or AUTO appears on display.
Programs do not run as expected · Make sure the switch is properly programmed.
· Note that – : – – indicates an inactive pro­gram, 00:00 indicates midnight.
· If the switch has been configured for 12-hour format, check that PM appears on the left side of the screen when an after­noon time is displayed.
The metal plate is hot This is normal with high loads (maximum of 500 W).

Honeywell Programmable Wall Switch - iCON Warranty

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials,  under normal use and service, for a period of
one (1) year from the date of first purchase by the original purchaser. If at any time during the warranty period the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option). If the product is defective,
(I) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii) call  ResideoCustomer Care at 1-800-468-1502. Customer Care
will make the determination whether the product should be returned to the following  address: Resideo Return Goods, 1985 Douglas Dr. N., Golden
Valley, MN 55422, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by damage that occurred while the product was in the possession of the consumer.  Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDE SHALL NOT BE LIABLE FOR AN
LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER  FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to
you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDE MAKES ON THIS  PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Resideo Customer Care,  1985Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.

Honeywell Programmable Wall Switch - Icon 1Customer Assistance 
If you have any questions about your light switch, go to
http://honeywellhome.com, or call Customer Care toll-free at
1-800-468-1502.Honeywell Programmable Wall Switch - bar code

Honeywell Programmable Wall Switch - Syambol
www.resideo.com

Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
69-2458EFS—07 M.S. Rev. 09-20 | Printed in the United States

© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International, Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.

Documents / Resources

Honeywell Programmable Wall Switch [pdf] Installation Guide
Honeywell, Programmable, Wall Switch, RPLS530A, RPLS531A

Leave a comment

Your email address will not be published.