Honeywell CT37 Series Powered By Android User Guide

Operating System: AndroidTM
Memory Card Specifications: Single Level Cell (SLC) industrial grade microSDTM, microSDHCTM, or microSDXCTM recommended

Features: Power Button, Scan Status LED/Speaker/Microphone, Battery Status/Notification LED, Front Camera, Ambient Light Sensor, Push-to-Talk Button, Touch Panel, Scan Button, Microphone, I/O Connector for Accessories, Camera Lens and Flash, Volume Button, Tray for Nano-SIM and/or MicroSD Card, USB Type C Connector, Speaker, NFC Antenna, Speaker Out for Bluetooth Low Energy Beacon, Battery, Microphone Barometer Sensor
Battery: Li-ion battery manufactured for Honeywell International Inc.

Product Usage Instructions

Memory Card Installation

Consult a Honeywell sales representative for qualified memory card options.

Power off the computer before installing or removing a memory card.

Battery Installation

Insert the Li-ion battery provided with the mobile computer.

Hand Strap Installation

Follow the appropriate steps based on the version of the hand strap.

Standard Version:
1. Install the hand strap as per instructions.
Healthcare Version (Sold Separately):
1. Install the healthcare hand strap for specific environments as per instructions.

Battery Charging

Charge the battery with a CT37 charging device for a minimum of 3 hours before initial use.
Avoid using the computer while charging to expedite the charging process.

Use only Honeywell accessories and power adapters to prevent damage not covered by warranty.

FAQ

Q: Can I use any memory card with the CT37 Series mobile computer?
- A: Honeywell recommends using Single Level Cell (SLC) industrial grade microSDTM, microSDHCTM, or microSDXCTM memory cards for optimal performance and durability. Contact a Honeywell sales representative for qualified options.
Q: How long should I charge the battery before initial use?
- A: It is recommended to charge the battery with a CT37 charging device for a minimum of 3 hours before initial use. Avoid using the computer while charging for quicker charging.

Agency Models

CT37 Series: CT37X0N, CT37X1N

Note: Due to variations in model configurations, your computer may appear different than illustrated.

Out of the Box

Make sure that your shipping box contains these items.

Standard SKUs:

CT37 mobile computer

Rechargeable Li-ion battery
Standard hand strap
Product Documentation

Healthcare SKUs:

CT37 mobile computer
Rechargeable Li-ion battery
USB Type C plug (SKU dependent, pre-installed)
Product Documentation
If you ordered accessories for your mobile computer, verify that they are also included with the order. Be sure to keep the original packaging in case you need to return the mobile computer for service.
Note: CT37X0N models do not include a WWAN radio.

Memory Card Specifications

Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD™, microSDHC™ or microSDXC™ memory cards with mobile computers for maximum performance and durability.
Contact a Honeywell sales representative for additional information on qualified memory card options.

Computer Features

Note: Due to variations in model configurations, your computer may appear different than illustrated.
Note: Hand strap not shown.

Install a Nano-SIM Card (WWAN Models)

Either a nano-SIM card or embedded SIM (eSIM) is used to activate the phone and connect to a mobile network. Refer to the user guide for additional information.

Note: Always power off the computer before attempting to install or remove a nano-SIM card.

Install a microSD Card (Optional)

Note: Format the microSD card before initial use.
Note: Always power off the computer before attempting to install or remove a microSD card.

About the Battery

The mobile computer ships with a Li-ion battery manufactured for Honeywell International Inc.
Before you attempt to use, charge or replace the battery in the device, carefully read all labels, markings and product documentation provided in the box or online at automation.honeywell.com.
To learn more about Battery Maintenance for Portable Devices, go to honeywell.com/PSS-BatteryMaintenance.

We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage not covered by the warranty.
Ensure all components are dry before placing the battery in the computer. Mating wet components may cause damage not covered by the warranty.

Install Battery

Install the Hand Strap (SKU Dependent) Standard Version

Note: See for the Healthcare hand strap version (sold separately).

Healthcare Version

Healthcare Version (Sold Separately)

Note: The optional hand strap for healthcare models is intended for use in environments where cleaning and disinfecting are performed.

Charge the Mobile Computer

The mobile computer ships with a partially charged battery. Charge the battery before initial use with a CT37 charging device for a minimum of 3 hours.
Note: Using the computer while charging the battery increases the time required to reach a full charge. If the mobile computer is drawing more current than supplied by the charging source, charging will not take place.

We recommend the use of Honeywell accessories and power adapters. Use of any non-Honeywell accessories or power adapters may cause damage not covered by the warranty.
CT37 series mobile computers are designed for use with CT37 charging accessories. For more information, see the CT37 Accessory Guide available for download at automation.honeywell.com.
Ensure all components are dry before mating the computers and batteries with peripheral devices. Mating wet components may cause damage not covered by the warranty.

About the USB Type C Connector

You can use a USB cable to charge the mobile computer from a host device (e.g., laptop or desktop computer). The connected host device must supply a minimum power output of 5V, 0.5A to the CT37 or the battery will not charge.
Note: On Healthcare SKUs, verify the USB Type C plug has been removed before attempting to attach a cable to the USB connector.

About the USB Type C Plug

Healthcare models include a protective plug for the USB Type C connector that is pre-installed.
When you reinstall the plug, make sure the plug is flush with the body of the computer.

Note: Do not use sharp or metallic instruments to install or remove the plug.
Note: Verify the plug is properly installed if intermittent charging and/or communication issues occur when the computer is placed in an accessory.

Turn Power On/Off

Note: Charge the battery before initial use with a CT37 charging device for a minimum of 3 hours.
The first time you power on the computer, a Welcome screen appears. You can either scan a configuration barcode or use the Wizard to manually set up the computer.
Once setup is complete, the Welcome screen no longer appears on startup and Provisioning mode is automatically turned off (disabled).

To turn the computer on:

Press and hold the power button for approximately 3 seconds and then release.

To turn the computer off:

Press and hold the Power button until the options menu appears.
Touch Power Off.

Battery Replacement

Hot Swap

The computer includes an internal battery that provides limited power for on-demand replacement of the main battery (i.e., hot swap).
You can replace the battery on demand provided the following conditions are met.
The internal battery is charged (see note).

You insert a charged battery within 60 seconds (30 seconds if the temperature is below 0 °C/32 °F).
Refer to the user guide for additional guidance on the use of the battery hot swap feature.
Note: The internal battery is charged via the main battery but can be depleted if too many consecutive hot swaps occur over a short time.

If a low internal battery notification displays, do not perform a hot swap until the notification clears. The internal battery is not user-replaceable.
Note: Do not install or remove the microSD card or nano-SIM card while performing a hot swap.

Screen Timeout

The screen timeout (sleep mode) automatically turns the touch panel display off and locks the computer to save battery power when the computer is inactive for a programmed period.
Press and release the Power button to wake the computer.

Adjust the Screen Timeout

To adjust the amount of time before the display sleeps after inactivity.

Swipe up on the touch screen.
Select Settings > Display > Screen Timeout.

Select the amount of time before the display goes to sleep.

About the Home Screen

Navigation and Function Buttons

For button locations, see Computer Features.

About Provisioning Mode

After completing the out-of-box set-up process, Provisioning mode is automatically turned off.

Scanning a barcode to install applications, certificates, configuration files, and licenses on the computer is restricted unless you enable Provisioning mode in the Settings app. To learn more, see the user guide.

Scan a Barcode with the Scan Demo

For optimum performance, avoid reflections by scanning the barcode at a slight angle.

Swipe up on the screen.
Select Demos > Scan Demo.
Point the computer at the barcode.

Touch Scan on the screen or press and hold any Scan button. Center the aiming beam over the barcode.

The decode results appear on the screen.

Note: In the Scan Demo app, not all barcode symbologies are enabled by default. If a barcode does not scan, the correct symbology may not be enabled. To learn how to modify the default app settings, see the user guide.

Sync Data

To move files between your CT37 and a computer.

Connect the CT37 to your computer using a USB charge/communication accessory.
On the CT37, swipe down from the top of the screen to see the notifications panel.

Touch the Android System notification twice to open the options menu.
Select either File Transfer or PTP.
Open the file browser on your computer.

Browse to the CT37. You can now copy, delete, and move files or folders between your computer and CT37 as you would with any other storage drive (e.g., cut and paste or drag and drop).
- Note: When Provisioning mode is turned off, some folders are hidden from view in the file browser.

Restart the Mobile Computer

You may need to restart the mobile computer to correct conditions where an application stops responding to the system or the computer seems to be locked up.

Press and hold the Power button until the options menu appears.
Select Restart.

To restart the computer if the touch panel display is unresponsive:

Press and hold the power button for approximately 8 seconds until the computer restarts.
Note: To learn about advanced reset options, see the user guide.

Support

To search our knowledge base for a solution or log into the Technical Support Portal and report a problem, go to honeywell.com/PSStechnicalsupport.

Documentation

Product documentation is available at automation.honeywell.com.

Limited Warranty

For warranty information, go to automation.honeywell.com and click Support > Productivity Solutions > Warranties.

Patents

For patent information, see www.hsmpats.com.

Trademarks

Android is a trademark of Google LLC.
Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners.

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult.
HII to determine whether any such changes have been made. HII makes no representation or warranties regarding the information provided in this publication.

HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results.
This document contains proprietary information that is protected by copyright. All rights are reserved.

No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII.

Documents / Resources

Honeywell CT37 Series Powered By Android [pdf] User Guide
Android 14, CT37 Series Powered By Android, CT37 Series, Powered By Android, By Android

References

User Manual

Honeywell CT37 Series Powered By Android

Product Information