QUICRUN Sensor Less Brushless Motor
“
Specifications
- Model: QUICRUN Outer 1621SL
- KV: 3500KV
- Lipo Cells: 2-3S
- No-load Current: 0.6
- Max. Output Power (W): 39.1
- Current @Max. Output Power(A): 9.52
- Diameter/Length: ≈15.8mm(0.62)
L=21mm(0.83) - Shaft Diameter/ Length: 2.0mm/9mm
- Poles Weight: 16.7g
- Applications: 1/24 Crawler
Product Usage Instructions
01 Warnings
Make sure to read and understand all warnings provided in the
user manual before operating the product.
02 Specifications
Refer to the specifications section above for detailed
information about the product’s model, KV, power, and other
technical details.
03 Installation & Connection
- Installation of the Motor:
There are 6 motor mounting holes in M2 specification with different
spacing options. Refer to the motor outline drawing for details
before installation. - How to Connect the Motor to an ESC:
Connect the A/B/C wires of the motor and ESC without specific
sequence requirements. Adjust wire connections if motor rotation is
incorrect. - Inspection:
Before powering on the ESC, verify motor installation and
connections.
04 Gearing
Proper gear ratio selection is crucial to prevent damage.
Consider factors like motor temperature when choosing gear
ratio.
FAQ
Q: Can I use this motor with a 4S LiPo battery?
A: No, this motor is recommended for use with 2-3S LiPo
batteries only. Using a higher voltage may damage the motor.
Q: How can I change the direction of motor rotation?
A: You can exchange any two wires connecting the motor to the
ESC or adjust the Motor Rotation parameter on the ESC settings.
“`
USER MANUAL
Sensorless Brushless Motor
QUICRUN Outer 1621
Thank you for purchasing this HOBBYWING product!
Improper use may cause damage to the product and related
ATTENTION
devices. We strongly recommend reading through this user
manual before use and strictly abide by the specified
operating procedures. We shall not be liable for any liability
CAUTIONS
arising from the use of this product, including but not
limited to reimbursement for incidental or indirect losses.
We do not assume any responsibility caused by unauthor-
ized modification of the product. We have the right to
change the product design, appearance, performance and
use requirements without notice.
01 Warnings
20240819
HW-SMB341DUL00
· Read the manuals of all the items being used in the build.Ensure gearing,setup,and overall install is correct and reasonable. · All connections,must be made correctly.You may loose control,or run into major issues caused by incorrect, bad,weak,or poor connections. · Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor may get damaged. · Stop usage if the motor exceeds 100¥/212,high temperature will damage the motor and cause the rotor to weaken.
02 Specifications
Model
KV
Lipo Cells
No-load Current
Max. Output Power (W)
Current @Max. Output Power(A)
Diameter/Length
Shaft Diameter/ Length
Poles Weight
Applications
QUICRUN Outer 1621SL 3500KV 2-3S 0.6
39.1
9.52
=15.8mm(0.62″) L=21mm(0.83″)
2.0mm/9mm
12 16.7g 1/24 Crawler
$$8
.
1)1
03 Installation & Connection
Battery
C
B
A
Electronic Speed Controller
Brushless motor
Receiver
1. Installation of the motor There are 6 motor mounting holes in M2 specification, and the mounting holes are 1.8mm in depth,before installing the motor on the vehicle, please carefully confirm whether the specifications of the screws are appropriate, as not to damage the motor due to excessive length. There are three types of mounting hole spacing of the motor, one group is 9mm, one group is 10mm, and one group is 12.5mm. Refer to the motor outline drawing for details.
2. How to Connect the Motor to an ESC There is no specific wire sequence requirement for the connection between the motor and the esc,the # A/# B/# C three wires of the motor and esc can be connected at will, if the motor rotation in the opposite direction, you can exchange any two wires,or set the “Motor Rotation” parameter of the esc..
3. Inspection Before powering on the esc, please check the motor installation and the order of all connections.
04 Gearing
Reasonable selection of gear ratio is very important. Improper gear ratio may cause damage. You can select the gear ratio according to the following points! 1. The operating temperature of the motor
The motor temperature should not exceed 100 degrees Celsius (212 degrees Fahrenheit) in operation. High temperature may cause the magnets to get demagnetized, the coil to melt and short circuit, and the ESC to get damaged. A suitable gearing ratio can effectively prevent the motor from overheating. 2. The principle of selecting gear ratio To avoid the possible damage to ESC and motor caused by the overheating, please start with a small pinion/a big FDR and check the motor temperature regularly. If the motor and ESC temperature always stays at a low level during the running, you can change a larger pinion/a lower FDR and also check the motor temperature regularly to ensure that the new gearing is suitable for your vehicle, local weather and track condition. (Note: For the safety of electric devices, please check the ESC and motor temperature regularly.)
4)&/;)&/)0##:8*/(5&$)/0-0(:$P
-5%c#VJMEJOH
:BTFO$IVBOHYJO)JUFDI*OEVTUSJBM1BSL
$IFOHYJO3PBE
#BPMPOH*OEVTUSJBM5PXO
-POHHBOH%JTUSJDU
4IFO[IFO
$IJOB
“VHVTU
Documents / Resources
 |
HOBBYWING QUICRUN Sensor Less Brushless Motor [pdf] User Manual QUICRUN Outer 1621SL 3500KV, HW-SMB341DUL00, QUICRUN Sensor Less Brushless Motor, QUICRUN, Sensor Less Brushless Motor, Less Brushless Motor, Brushless Motor |