HOBBYWING QuicRun 2030 G2 Sensor Less Brushless Motor

Specifications:

• Model: QUICRUN 2030 G2
• KV: 5000KV, 6500KV, 7800KV
• Lipo No-load Cells Current:
  • QUICRUN 2030SL G2-5000KV: 2-3S, 1.05A
  • QUICRUN 2030SL G2-6500KV: 2S, 1.2A
  • QUICRUN 2030SL G2-7800KV: 2S, 1.3A
• Diameter/Length: =20mm(0.79) L=31mm(1.22)
• Shaft Diameter/Length: =2mm(0.08) L=12mm(0.47)
• Bearing size: D8*D3*T4
• Poles: 2
• Weight: 42g
• Applications: On-road & Off-road, 1/18 scale

Product Usage Instructions

Warnings:
Read the user manual carefully to prevent personal injury or damage to the product and related devices.

Installation & Connection:

1. Installation of the Motor:
   Check the motor mounting holes and ensure correct screw specifications to avoid damage. Refer to the motor outline drawing for mounting hole spacing details.
2. How to Connect the Motor to an ESC:
   No specific wire sequence is required. Connect the #A/#B/#C wires of the motor and ESC freely. If motor rotation is incorrect, exchange any two wires.
3. Inspection:
   Before powering on the ESC, verify motor installation and connections.

Gearing:
Selecting the appropriate gear ratio is crucial to prevent damage. Consider the operating temperature of the motor when choosing the gear ratio.

WARNING

Thank you for purchasing this HOBBYWING product! Improper use may cause personal injury and damage to the product and related devices. We strongly recommend reading through this user manual before use and strictly abide by the specified operating procedures.

CAUTION
We shall not be liable for any liability arising from the use of this product, including but not limited to reimbursement for incidental or indirect losses. We do not assume any responsibility caused by unauthorized modification of the product. We have the right to change the product design, appearance, performance and use requirements without notice.

Warnings

• Read the manuals of all the items being used in the build.Ensure gearing,setup,and overall install is correct and reasonable.
• All connections,must be made correctly.You may loose control,or run into major issues caused by improper, bad,weak,or poor connections.
• Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor may get damaged.
• Stop usage if the motor exceeds 100℃/212℉,high temperature will damage the motor and cause the rotor to weaken.

SPECIFICATION

Model	KV	Lipo Cells	No-load Current	Diameter/Length	Shaft Diameter/ Length	Bearing size	Poles	Weight	Applications
QUICRUN 2030SL G2-5000KV	5000KV	2-3S	1.05A		ϕ=2mm(0.08″) L=12mm(0.47″)	D8*D3*T4	2	42g	1/18 On-road&Off-road
QUICRUN 2030SL G2-6500KV	6500KV	2S	1.2A	ϕ=20mm(0.79″) L=31mm(1.22″)				42g
QUICRUN 2030SL G2-7800KV	7800KV	2S	1.3A					43g

DIMENSIONS

Installation & Connection

1. Installation of the motor
   There are 6 motor mounting holes in M2.5 specification, and the mounting holes are 3.8mm in depth,before installing the motor on the vehicle, please carefully confirm whether the specifications of the screws are appropriate, as not to damage the motor due to excessive length. There are three types of mounting hole spacing of the motor, one group is 12.6mm, one group is 14mm, and one group is 16mm. Refer to the motor outline drawing for details.
2. How to Connect the Motor to an ESC
   There is no specific wire sequence requirement for the connection between the motor and the esc,the # A/# B/# C three wires of the motor and esc can be connected at will, if the motor rotation in the opposite direction, you can exchange any two wires.
3. Inspection
   Before powering on the esc, please check the motor installation and the order of all connections.

Gearing

Reasonable selection of gear ratio is very important. Improper gear ratio may cause damage. You can select the gear ratio according to the following points!

1. The operating temperature of the motor
   The motor temperature should be lower than 100 degrees Celsius (212 degrees Fahrenheit) in operation. High temperature may cause the magnets to get demagnetized, the coil to melt and short circuit, and the ESC to get damaged. A suitable gearing ratio can effectively prevent the motor from overheating.
2. The principle of selecting gear ratio
   To avoid the possible damage to ESC and motor caused by the overheating, please start with a small pinion/a big FDR and check the motor temperature regularly. If the motor and ESC temperature always stays at a low level during the running, you can change a larger pinion/a lower FDR and also check the motor temperature regularly to ensure that the new gearing is suitable for your vehicle, local weather and track condition. (Note: For the safety of electric devices, please check the ESC and motor temperature regularly.)

SHENZHEN HOBBYWING TECHNOLOGY Co., LTD. · 101-402 Building 4, Yasen Chuangxin Hi-tech Industrial Park, 8 Chengxin Road, Baolong Industrial Town, Longgang District, Shenzhen, China. April 09, 2024

FAQ

Q: Can I use this motor with a higher voltage battery than specified?
A: It is not recommended to exceed the specified voltage range as it may cause damage to the motor and related components.

Q: What should I do if the motor rotation is incorrect after connecting to the ESC?
A: Simply exchange any two of the #A/#B/#C wires between the motor and ESC to correct the rotation direction.

Documents / Resources

HOBBYWING QuicRun 2030 G2 Sensor Less Brushless Motor [pdf] User Manual QUICRUN 2030SL G2-5000KV, QUICRUN 2030SL G2-6500KV, QUICRUN 2030SL G2-7800KV, QuicRun 2030 G2 Sensor Less Brushless Motor, QuicRun 2030 G2, Sensor Less Brushless Motor, Less Brushless Motor, Brushless Motor

References

• User Manual