P / N: 110401111255X

UAS 18E
Voltage thiab Continuity Tester
Phau ntawv ua haujlwm

Cov cim xa mus rau hauv phau ntawv

Phau ntawv suav nrog cov ntaub ntawv tsim nyog hais txog kev siv nyab xeeb thiab kev saib xyuas cov cuab yeej siv thiab ua ntej siv, nyeem hauv txhua ntu ntawm
phau ntawv.
Tsis nyeem phau ntawv lossis nkag siab txog cov cuab yeej siv cov txheej txheem teev tseg hauv phau ntawv yuav ua rau lub cev raug mob thiab cov khoom puas tsuaj.

	Txaus ntshai Voltage
	Cov ntaub ntawv tseem ceeb. Thov xa mus rau cov ntawv qhia.
	Ob chav rwb thaiv tsev
	Haum rau kev ua neej thiab ua haujlwm
	Tsis txhob muab cov khoom pov tseg raws li cov khoom pov tseg uas tsis tau cais tawm hauv nroog. Muab lawv tso rau hauv cov roj teeb uas tau muab tso rau hauv recycle bin rau pov tseg ntxiv.
	EU Certification
	UKCA Cov Ntawv Pov Thawj
MIV III	Kev ntsuas qeb III muaj feem xyuam rau kev ntsuas thiab ntsuas cov hluav taws xob txuas nrog rau qhov kev faib tawm ntawm lub tsev qis-vol.tage MAINS installation.
MIV IV	Kev ntsuas qeb IV muaj feem xyuam rau kev ntsuas thiab ntsuas kev sib txuas ntawm lub hauv paus ntawm lub tsev qis-vol.tage MAINS installation.

Cov cim ntawm lub vaj huam sib luag tester thiab nws cov lus piav qhia (Daim duab 1)

1. Test cwj mem L1; 2. Test cwj mem L2; 3. Pov Lis Voltage qhia (LED); 4. LCD zaub; 5. High-voltage qhia; 6. AC qhia; 7. Kev taw qhia txuas ntxiv; 8. Polar qhia;

9. Rotary theem qhia; 10. RCD qhia (LED); 11. RCD kuaj khawm; 12. khawm tshuaj xyuas tus kheej; 13. HOLD hom / backlight khawm; 14. Lub taub hauamp 15. Test cwj mem cap; 16. Roj teeb npog

Daim duab 2 muab cov lus piav qhia ntxaws ntawm LCD vaj huam sib luag.

1. Qhov taw qhia ntsiag to hom; 2. HOLD hom qhia; 3. Tsawg-voltage roj teeb qhia; 4. Pov Lis Voltage ntsuas;

5. Kev ntsuas zaus; 6. DC Voltage ntsuas 7. AC Voltage ntsuas;

Kev qhia ua haujlwm thiab siv qhov ntsuas ntawm tus ntsuas

Voltage thiab continuity tester UT18E muaj xws li AC / DC (suav nrog peb-theem alternating tam sim no) voltage ntsuas, peb-theem AC theem qhia, ntsuas zaus, RCD xeem, ntsuas txuas ntxiv, qhov kev sim yooj yim yog tias tsis muaj roj teeb fais fab, kev tshuaj xyuas tus kheej, xaiv hom ntsiag to, overvoltage indication thiab low-voltage roj teeb qhia. Tsis tas li ntawd, lub teeb nyem txuas nrog rau tus cwj mem xeem muab cov ntawv thov yooj yim hauv qhov chaw tsaus.
Txhawm rau tiv thaiv tester thiab tus neeg siv khoom siv, tus tester yog nruab nrog lub tsho tiv thaiv. Lub tester yuav tsum tau muab tso rau ntawm lub tsho tiv thaiv tom qab siv, thiab xa mus, muab tso rau hauv cov khoom siv los tiv thaiv kev puas tsuaj. Tsis txhob tso tus tester rau hauv koj lub hnab ris.
Lub tester siv tau rau ntau lub sijhawm xws li tsev neeg, lub Hoobkas, chav haujlwm fais fab, thiab lwm yam.
Nws muaj cov yam ntxwv hauv qab no:

1. Txhawm rau tiv thaiv kev raug mob ntawm lub cev, nws yog tsim los tiv thaiv lub tsho;
2. LED qhia;
3. LCD voltage thiab zaus tso saib;
4. AC / DC ntsuas txog 1000V;
5. Kev ntsuas txuas ntxiv;
6. Qhia txog theem kev sib raug zoo ntawm peb-theem AC;
7. Ob lub buzzing thiab ntsiag to hom yog xaiv tau;
8. Kev kuaj pom tsis muaj roj teeb;
9. Lub teeb muaj nuj nqi;
10. Kev tshuaj xyuas tus kheej muaj nuj nqi;
11. Tsawg-roj teeb voltage qhia thiab ntsuas voltage tshaj ntau yam qhia; Nws tsis tuaj yeem ntsuas thiab xav tau hloov lub roj teeb.
12. RCD xeem;
13. Tsis siv neeg standby.

Kev ceev faj txog kev nyab xeeb

Txhawm rau tiv thaiv kev raug mob ntawm lub cev, hluav taws xob poob lossis hluav taws, ua tib zoo saib xyuas cov khoom hauv qab no:

• Nco ntsoov tias ob lub xeem cwj mem thiab ntsuas ntsuas tsis zoo ua ntej kuaj;
• Nco ntsoov khaws koj txhais tes nkaus xwb nrog tus kov thaum siv cov khoom siv;
• Tsis txhob siv cov khoom siv thaum lub voltage yog dhau qhov ntau (xa mus rau cov kev qhia tshwj xeeb) thiab siab dua 1100V;
• Ua ntej siv, nco ntsoov tias cov cuab yeej siv tau zoo;
• Txhawm rau kom ntseeg tau tias kev ua haujlwm zoo ntawm cov ntsuas ntsuas, ntsuas qhov paub txog voltage tus nqi hauv thawj.
• Lub tester tsis tuaj yeem siv ntxiv yog tias muaj ib lossis ntau qhov ua haujlwm tsis ua haujlwm lossis tsis muaj qhov qhia txog kev ua haujlwm.
• Tsis txhob sim hauv cov dej ntub dej.
• Cov zaub ua haujlwm zoo tsuas yog thaum qhov kub ntawm -15 ° C ~ + 45 ° C thiab cov av noo ntawm <85%.
• Cov cuab yeej yuav tsum tau kho yog tias tus kheej kev nyab xeeb ntawm tus neeg teb xov tooj tsis tuaj yeem lav.

1. Kev nyab xeeb yuav tsis tau lav nyob rau hauv ib qho ntawm cov xwm txheej hauv qab no:
   a. Pom kev puas tsuaj;
   b. Tester cov haujlwm tsis sib haum nrog cov haujlwm uas nws yuav tsum muaj.
   c. Nws tau muab khaws cia rau hauv cov xwm txheej tsis tsim nyog tau ntev.
   d. Kawm txog kev siv tshuab extrusion hauv kev thauj mus los.

Voltage ntsuas

Ua raws li cov cai ntsuas kev nyab xeeb uas tau teev tseg hauv nqe 3.
Voltage iav ntawm tester yog tsim los ntawm ib kab ntawm LED, nrog rau 12V, 24V, 50V, 120V, 230V, 400V, 690V thiab 1000V, LED yuav teeb ib tom qab nrog rau kev nce vol.tage, kuj suav nrog cov polarity LED qhia, AC LED qhia, on-off LED qhia, RCD LED qhia, rotary theem LED qhia thiab high-voltage LED qhia.

1. Ua kom tiav tus kheej kuaj ntawm tester ua ntej kuaj. Tom qab nias lub teeb nyem qhov tseem ceeb 5s, tus neeg ntsuas yuav ua AC / DC tag nrho cov kev tshawb pom, nrog rau lashing LED (nrog rau RCD lub teeb) thiab blinking displayed LCD. Yog xav tau tawm ntawm kev kuaj xyuas tus kheej, tsuas yog kov lub teeb nyem. Txuas ob lub xeem cwj mem mus rau tus neeg xyuas pib ntsuas, xaiv qhov paub voltage rau kev ntsuas, xws li 220V socket, thiab xyuas kom meej qhov ntsuas qhov tseeb (Saib daim duab 3). Lub tester tsis tuaj yeem ntsuas AC thiab DC voltage tsawg dua 5V thiab tsis qhia qhov tseeb thaum ntsuas voltage yog 5Vac/de. Illuminating continuity teeb los yog AC teeb thiab beeping buzzer yog ib txwm.
   
2. Tester yuav muab LED + LCD qhia thaum ntsuas AC lossis DC voltage. High-voltage LED yuav illuminated thiab buzzer beeps thaum ntsuas voltage yog voltage (ELV) qhov pib. Yog ntsuas voltage tseem nce ntxiv thiab tshaj tawm tswv yim tiv thaiv voltage ntawm lub tester, 12V ~ 1000V LED yuav ua kom flashing, LCD qhia "OL" thiab buzzer tseem beeping.
3. Rau ntsuas DC voltage, yog tias L2 thiab L1 txuas nrog rau qhov zoo thiab qhov tsis zoo ntawm cov khoom yuav tsum tau ntsuas, LED yuav qhia qhov sib thooj vol.tage, LCD qhia lub voltage, lub sijhawm no, LED qhia tus ncej zoo yuav pom, LCD qhia "+'"VDC" thiab, ntawm qhov tsis sib xws, LED qhia tus ncej tsis zoo yuav pom, LCD qhia "-" "VDC". Yog tias xav tau los txiav txim qhov zoo thiab qhov tsis zoo ntawm cov khoom yuav tsum ntsuas, txuas ob lub ntsuas ntsuas rau cov khoom kom ntsuas random, lub teeb pom kev zoo ntawm LED lossis LCD "+" ntawm cov ntsuas ntsuas txhais tau tias lub davhlau ya nyob twg txuas rau L2 yog qhov zoo thiab lwm qhov txuas rau L1 yog qhov tsis zoo.
4. Kev ntsuas AC voltage, ob lub cwj mem xeem yuav raug txuas mus rau ob qhov kawg ntawm cov khoom ntsuas, "+", "-" LED yuav teeb pom kev, LCD qhia "VAC" thaum LED qhia txog qhov sib thooj.tage tus nqi thiab LCD qhia tau sib xws voltage nqi.

Nco tseg: Kev ntsuas AC voltage, L thiab R theem inversion qhia LED yuav illuminated, nws txhais tau hais tias theem qhia tsis ruaj, L lub teeb los yog R teeb yog illuminated, thiab txawm L thiab R teeb yuav illuminated hloov lwm lub tsev; L thiab R teeb yuav tsis muab qhov tseeb thiab ruaj khov tshwj tsis yog ntsuas peb theem fais fab.

Kev soj ntsuam tsis muaj roj teeb

Tus tester tuaj yeem ua qhov yooj yim nrhiav tau thaum lub roj teeb tag lossis tsis muab roj teeb. Txuas ob tus cwj mem mus rau qhov khoom yuav ntsuas, thaum qhov khoom muaj voltage siab tshaj los yog sib npaug rau 50VAC / 120VDC, siab-voltage LED yuav illuminated, qhia voltage thiab LED yuav maj mam brightened nrog rau voltage yuav ntsuas.

Kev sim txuas ntxiv

Yuav kom paub meej tias tus neeg xyuas pib yuav ntsuas tau hluav taws xob, voltage txoj kev ntsuas yuav raug coj los ntsuas qhov voltage ntawm ob qho kawg ntawm tus neeg xyuas pib los ntawm kev siv ob daim ntawv xeem. Txuas ob lub xeem cwjmem rau ob qho kawg ntawm cov khoom yuav ntsuas, yog tias qhov kev tiv thaiv ntog hauv 0 ~ 60kQ, txuas ntxiv LED yuav teeb pom kev zoo, nrog rau lub suab nrov nrov; thiab yog tias tsis kam poob rau hauv 6 (0KQ ~ 150kQ, txuas ntxiv LED yuav lossis tsis tuaj yeem pom thiab buzzer yuav lossis tsis tuaj yeem beep; yog tias tsis kam yog> 150kQ, txuas ntxiv LED yuav tsis pom thiab buzzer yuav tsis beep. paub tseeb tias cov khoom yuav ntsuas tsis tau hluav taws xob.

Kev ntsuas kev sib hloov (peb-theem AC theem qhia)

Kev ntsuas yuav tsum tau ua raws li cov cai ntsuas kev nyab xeeb uas tau teev tseg hauv cov khoom R, LLED lossis Land R cov cim qhia muaj feem xyuam rau kev sib hloov thiab kev xeem tsuas yog siv tau rau peb-theem AC system.

1. Peb theem voltage xeem ntau yam: 100V ~ 400V (50Hz ~ 60Hz);
2. Tuav lub cev tseem ceeb ntawm tus ntsuas (nrog rau tus ntiv tes tuav), raws li qhia hauv daim duab hauv qab no, txuas tus cwj mem L2 mus rau txhua theem thiab L1 rau ib qho ntawm ob theem ntxiv.
3. R lossis LLED yuav raug teeb pom kev zoo, thiab tom qab txuas tus cwj mem mus rau lwm theem, lwm LED (L lossis R) yuav pom.
4. Lor R LED yuav illuminated raws li thaum txoj hauj lwm ntawm ob lub xeem cwj mem pauv.
5. LED yuav qhia qhov sib thooj voltage los yog LCD qhia voltage tus nqi, qhov qhia lossis tso tawm voltage yuav tsum yog theem voltage tiv thaiv ntiaj teb tab sis peb-theem voltage.
   Daim duab peb-theem hluav taws xob ntsuas qhov system (Daim duab 4)

Nco tseg: Rau kev ntsuas peb-theem AC system, txuas peb lub ntsuas qhov ntsuas mus rau qhov sib txuas ntawm lub davhlau ya nyob twg ntawm peb-theem system thiab, txij li tus ntsuas ntsuas tsuas muaj ob lub ntsuas ntsuas ntsuas, nws yuav tsum tsim lub davhlau ya nyob twg los ntawm kev tuav tus ntsuas ntsuas nrog ntiv tes (los ntawm lub hauv av), yog li nws yuav tsis raug qhia txog theem theem ntawm peb-theem system yog tias tsis tuav tus kov lossis hnav hnab looj tes insulating. Tsis tas li ntawd, nws yog ib qho tsim nyog los xyuas kom meej lub ntiaj teb davhlau ya nyob twg (lub ntiaj teb hlau los yog plhaub) ntawm peb-theem system nyob rau hauv kev sib cuag nrog tib neeg lub cev thaum ntsuas peb-theem fais fab system qis dua 100V.

RCD xeem

Kom txo kev ntxhov siab voltage thaum voltage kev ntsuas, ib lub voj voog uas muaj impedance qis dua tus ntsuas ntsuas raws li kev ntsuas ib txwm tuaj yeem muab los ntawm ob lub ntsuas ntsuas, uas yog RCD Circuit Court system.
Rau RCD mus ncig teb chaws xeem, txuas ob lub xeem cwj mem mus rau L thiab PE davhlau ya nyob twg ntawm 230Vac system nyob rau hauv ib txwm voltage ntsuas hom thiab nias RCD tus yuam sij "+" ntawm ob lub ntsuas ntsuas, RCD system yuav mus ncig thiab LED qhia RCD yuav teeb pom kev yog tias lub Circuit Court ces tsim AC tam sim no siab dua 30mA. Tshwj xeeb, yog tias RCD tsis tuaj yeem ntsuas tau ntev thiab, ntawm 230V, lub sijhawm ntsuas yuav tsum yog <10s, tsis tuaj yeem ntsuas qhov txuas ntxiv thiab, tom qab ib zaug sim, tos 60s ua ntej ntsuas tom ntej.
Nco tseg: Yog tias tsis muaj kev ntsuas lossis ntsuas, nws yog ib txwm ua kom muaj lub teeb ci tsis tu ncua LED thiab nruam beeping buzzer tom qab ib txhij nias RCD yuam sij ntawm ob lub ntsuas ntsuas. Txhawm rau kom tsis txhob ua haujlwm tsis zoo, tsis txhob nias ob lub RCD yuam sij nyob rau hauv tsis yog-RCD kuaj hom.

Kev xaiv hom ntsiag to

Nws raug tso cai nkag mus rau hom ntsiag to thaum lub ntsuas ntsuas nyob rau hauv hom standby lossis ib txwm siv. Tom qab nias lub teeb nyem txog 1s, tester yuav bleep thiab LCD qhia silence cim " ”, thiab tester nkag mus rau hom ntsiag to thiab, nyob rau hauv hom twg, txhua txoj haujlwm zoo ib yam li cov hauv qab hom, tshwj tsis yog rau lub suab ntsiag to. Yog tias xav tau rov ua haujlwm li qub (hom buzzing), nias lub teeb nyem txog 1s, thiab, tom qab "bleeps", lub cim ntsiag to " "ntawm LCD yuav ploj mus.

Kev siv lub teeb nyem ua haujlwm

Lub teeb ua haujlwm yuav raug xaiv yog tias xav tau siv lub ntsuas ntsuas thaum hmo ntuj lossis hauv qhov chaw tsaus; Tom qab lub teeb kov ntawm lub teeb nyem khawm ntawm lub vaj huam sib luag tester, lub headlamp nyob rau sab saum toj ntawm lub tester yuav tsum tau qhib los pab txhawb koj txoj haujlwm thiab, tom qab ua haujlwm, tua lub teeb nrog lub teeb kov ntawm lub pob.

Kev siv HOLD muaj nuj nqi

Txhawm rau kom yooj yim nyeem thiab sau, tuav cov ntaub ntawv ntsuas (voltage thiab zaus tus nqi) los ntawm lub teeb kov ntawm HOLD ntawm tester thaum siv tester; tom qab lwm lub teeb kov, tuav raws li txoj cai yog relieved thiab rov qab mus rau ib txwm kuaj.

Hloov roj teeb

qis voltage lub cim ntawm LCD thaum siv lub ntsuas ntsuas qhia tias tsis muaj roj teeb voltage thiab qhov tsim nyog ntawm kev hloov roj teeb.

Hloov roj teeb raws li cov txheej txheem hauv qab no (raws li qhia hauv daim duab 5):

1. Tso tseg kev ntsuas thiab txiav ob lub ntsuas ntsuas los ntawm cov khoom ntsuas;
2. Ntsia hlau tawm screws ruaj lub roj teeb npog nrog screwdriver;
3. Tshem lub roj teeb npog;
4. Tshem tawm lub roj teeb los hloov;
5. Nruab lub roj teeb tshiab raws li lub cim roj teeb thiab cov lus qhia ntawm lub vaj huam sib luag;
6. Ntxig lub roj teeb npog thiab tuav nws nrog screws.

Nco tseg: Rau kev tiv thaiv ib puag ncig, cov roj teeb tuaj yeem raug sau thiab rov ua dua ntawm qhov chaw khaws khoom ruaj khov thaum muab cov roj teeb pov tseg lossis cov khoom ntim uas muaj cov khoom pov tseg.
Thov ua raws li cov cai hauv zos uas siv tau rov ua dua tshiab thiab pov tseg cov roj teeb hloov raws li cov cai pov tseg rau cov roj teeb qub thiab cov khoom ntim.

Cov cuab yeej tu

Tsis muaj kev saib xyuas tshwj xeeb tshwj tsis yog tus neeg ntsuas yuav tsum tau siv raws li phau ntawv qhia thiab, yog tias muaj kev ua haujlwm tsis zoo thaum lub sijhawm ua haujlwm ib txwm, tsum tsis txhob siv tam sim ntawd thiab hu rau qhov chaw pabcuam uas tau tso cai ze tshaj plaws.

Cov cuab yeej tu

Ua ntej ntxuav, disconnect tester los ntawm Circuit Court raug kuaj. Yog tias qhov ntsuas tau qias neeg thaum siv ib txwm siv, so nws nrog cov ntaub ntub dej lossis cov khoom siv me me ntawm cov tshuaj ntxuav tsev zoo es tsis txhob siv cov kua qaub los yog cov kuab tshuaj. Tsis txhob siv lub tester hauv 5h tom qab ntxuav.

Technical qhia

Muaj nuj nqi	Ntau yam	Qhov tseeb/Function
LED (AC / DC) Voltage indication (V)	12v XNUMX	8V ± 1V
	24v XNUMX	18V ± 2V
	50v XNUMX	38V ± 4V
	120v XNUMX	94V ± 8V
	230v XNUMX	180V ± 14V
	400v XNUMX	325V ± 15V
	690v XNUMX	562V ± 24V
	1000v XNUMX	820V ± 30V
Phase rotation test (three-theem voltage)	Voltage ntau: 100V-400V	√
	Zaus: 50Hz-601-1z	√
Kev sim txuas ntxiv	Qhov tseeb 'Rn + 50%	√
	Beeper thiab LED illumination	√
RCD xeem	Voltage: 230V, Zaus: 50Hz-400Hz	√
Kev ntsuas polarity	Positive & Negative (auto)	√
Kev tshuaj xyuas tus kheej	Tag nrho LED teeb pom kev zoo los yog LCD puv npo	√
Nrhiav tau voltage tsis muaj roj teeb	100V-1000V AC / DC	√
Nws pib ntau yam	Muaj ntau yam	√
Teeb nyem	Muaj ntau yam	√
Tsawg-roj teeb voltage lus	Txog 2.4V	√
Tshaj-voltage kev tiv thaiv	Txog 1100V	√
Nws pib standby	Standby tam sim no <10uA	√
Hom uas ntsiag to	Muaj ntau yam	√
LCD zaub (voltage)	6V-1000V daws teeb meem: 1V	± [1.5% + (1-5) Tus lej]
LCD zaub (ntau zaus)	40Hz-400Hz daws teeb meem: 1Hz	± (3% + 5)

LCD zaub qhov tseeb qhov taw qhia:

6V	12V / 24V	50v XNUMX	120v XNUMX	230V / 400V / 690V / 1000V
± (1.5% + 1)	± (1.5% + 2)	± (1.5% + 3)	± (1.5% + 4)	± (1.5% + 5)

Function thiab parameter piav qhia

• Buzzing thiab ntsiag to hom yog xaiv tau;
• Lub sij hawm teb: LED <0.1s / LCD <1s
• Peak tam sim no ntawm kev xeem Circuit Court: Yog <3.5mA (ac/dc)
• Test lub sij hawm: 30s
• Lub sij hawm rov qab: 240s
• RCD xeem: Ntau yam: 230V (50Hz ~ 400Hz); AC tam sim no: 30mA ~ 40mA; Test lub sij hawm <10s, lub sij hawm rov qab: 60s;
• Ua haujlwm kub ntau: -15 ° C ~ + 45 ° C
• Cia kub ntau: -20 ° C ~ + 60 ° C
• Ua haujlwm av noo: <85% RH
• Siv thaj chaw: Nyob sab hauv tsev
• Ua haujlwm qhov siab: <2000m
• Kev ntsuas kev nyab xeeb: CAT Ill 1000V, CAT IV 600V
• Cov pa phem: 2
• Ua raws li: CE, UKCA
• Cov qauv: EN 61010-1: 2010 + A1: 2019, EN IEC 61010-2-033: 2021 + A11: 2021, BS EN 61010-1: 2010 + A1: 2019, EN 61326-1: 2013 -61326:2, EN 2-2013:61243
• Luj: 277g (nrog rau roj teeb);
• Loj: 272 * 85 * 31mm
• Roj teeb IEC LRO3 (AAA) x2

UNI-TREND TECHNOLOGY (CHINA) CO., LTD.
No.6, Gong Ye Bei 1st Road, do Songshan Lake National High-Tech Industrial
Kev Tsim Tsam Thaj Tsam, Dongguan City,
Guangdong xeev, Suav teb

Cov ntaub ntawv / Cov ntaub ntawv

	UNI-T UT18E Voltage thiab Continuity Tester [ua pdf] Tus neeg siv phau ntawv UT18E, Voltage thiab Continuity Tester, UT18E Voltage thiab Continuity Tester, Continuity Tester, Tester
	UNI-T UT18E Voltage thiab Continuity Tester [ua pdf] Tus neeg siv phau ntawv UT18E Voltage thiab Continuity Tester, UT18E, Voltage thiab Continuity Tester, Continuity Tester

Cov ntaub ntawv

• Cov neeg siv phau ntawv