AR-837-EA Graphic Display Multi-Function Proximity Controller
Phau ntawv qhia

Cov ntsiab lus

AR-837-EA: Lub ntsej muag lees paub

1. Cov khoom
   
2. Terminal Cables
   
3. Cov cuab yeej
   
4. Xaiv tau
   • Ethernet: DMOD-NETMA10
   (TCP / IP Module suav nrog RJ45 Connector)
   Or
   DMOD-NETMA 11
   (TCP / IP Module nrog POE muaj nuj nqi)
   • Ib qho Wiegand Output Module (CN10)
   • AR-MDL-721V (Voice Module)
   • AR-321 L485-5V (TTY rau RS-485 Converter)

Kev teeb tsa

Txoj Kev Txhim Kho

• A-1. Nto Mounted: Siv lub hau ntswj kom ntsia hlau rau ntawm phab ntsa.
• A-2. Embedded: khawb ib lub qhov rau 128mmx109mm; thiab tom qab ntawd, siv tus ntsia hlau ntsia hlau ntsia hlau rau ntawm phab ntsa.
• Rub cable xaus los ntawm qhov nkag mus rau hauv lub phaj mounting.
• Txuas AR-837-EA rau lub mounting phaj thiab nruab screws (muab) rau hauv lub qhov nyob rau hauv qab nrog tus yuam sij Allen.
• Siv zog. LED (ntsuab) yuav teeb nrog ib lub suab nrov.

Qhov Loj (mm)

• Nto mounting qhov (Pem hauv ntej View) • Flush-mounting qhov (Pem hauv ntej View)	• Nto mounting qhov (Sab view)	• Flush-mounting qhov (Sab view)

Daim ntawv qhia kev teeb tsa

Nto / Flush-mounted Multifunctional Face & RFID Recognition Controller

Daim ntawv ceeb toom

1. Tubing: Cov xov hlau sib txuas lus thiab cov kab hluav taws xob yuav tsum tsis txhob muab khi rau hauv tib lub kav dej lossis tubing.
2. Hlau xaiv: Siv AWG 22-24 Shielded Twist Pair kom zam lub hnub qub thaiv, CAT 5 cable rau TCP / IP kev twb kev txuas
3. Fais fab mov: Tsis txhob nruab tus nyeem ntawv thiab xauv nrog tib lub hwj huam mov. Lub hwj chim rau tus nyeem ntawv yuav tsis ruaj khov thaum lub ntsuas phoo qhib, uas yuav ua rau tus nyeem ntawv tsis ua haujlwm.
   Tus txheej txheem installation: Lub qhov rooj relay thiab xauv siv tib lub hwj huam mov, thiab tus nyeem ntawv yuav tsum siv lwm lub hwj chim ywj siab.

Connector Table (1)

kab: CN3

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
Anti-T.ampua Switch	1	Liab	NC
	2	Txiv kab ntxwv	COM
	3	Daj	TSIS MUAJ

kab: CN4

Daim Ntawv Thov Hlau	Hlau	Xim 'Kev piav qhia
Xauv Relay	1	Xiav Dawb (N 0.)DC24V1Amp
	2	Ntshav Dawb (NC) DC24V1Amp
Xauv Relay COM	3	Dawb	(COM) DC24V1Amp
Qhov Rooj Sib Tham	4	Txiv kab ntxwv	Negative Trigger Input
Tawm Tawm	5	Ntshav	Negative Trigger Input
Tswb Relay	6	Grey	ND / NC yeem (los ntawm jumper)
Hwj chim	7	Tuab Liab	DC 12 V
	8	Dub tuab	DC OV

kab: CN6

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
RS-485 rau Lift Controller	1	Ntsuab Ntsuab	RS-485 (B-)
	2	Thick Blue	RS-485 (A +)

kab: CN5

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
Beeper	1	Paj yeeb	Beeper tso zis 5V / 100mA, Tsawg
LED	2	Daj	Liab LED tso zis 5V / 20mA, Max
	3	Xim av	Ntsuab LED tso zis 5V / 20mA, Max
Qhov rooj tso zis	4	Xiav Dawb	Transistor tso zis Max. 12V / 100mA (Qhib Collector Active Tsawg)
Wiegand	5	Nyias Ntsuab	Wiegand DAT: 0 Input
	6	Nyias xiav	Wiegand DAT: 1 Input
WG Qhov Rooj Sib Tham	7	Txiv kab ntxwv	Negative Trigger Input
WG Exit Switch	8	Ntshav	Negative Trigger Input

kab: CN8

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
Khaws tseg	1	Liab	—
Kev ruaj ntseg trigger teeb liab	2	Ntshav	Kev ruaj ntseg txhais teeb liab Output
Caj npab	3	Liab Dawb	Arming Output
Duress	4	Yellow Dawb	Duress Tso zis

kab: CN13

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
Rooj Tswb	1	Dub Dawb	Transistor tso zis Max. 12V / 100mA (Qhib Collector Active Tsawg)
	2	Dub	DC OV

kab: CN7

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
	1	—	—
	2	—	—
TCP/IP tso zis	3	Txiv kab ntxwv Dawb	Net - TX+
	4	Txiv kab ntxwv	Net - TX-
	5	Ntsuab Dawb	Net - RX+
	6	Kab mob	Net - RX-
	7	—	—

kab: CN9

Daim Ntawv Thov Hlau	Hlau	Xim	Kev piav qhia
Suab Module (*Yuav tsum tau hais lus 8Ω / 1.5W (Max. 2 W)	1	Dub	DC OV
	2	Daj	TX
	3	Dawb	TE
	4	Txiv kab ntxwv	RX
	5	Liab	DC 5 V
	6	Xiav

kab: CN10

Hlau Daim Ntawv Thov Hlau		Xim	Kev piav qhia
HID RF module	1	Txiv kab ntxwv	NTAWV 1
	2	Ntshav	NTAWV 2
	3	Dub	DC OV
	4	Liab	DC 5 V
	5	Xiav	Wiegand DAT: 1 Input
	6	Ntsuab	Wiegand DAT: 0 Input
	7	Dawb	1 XNUMXm

Kab kos duab

Txuas rau Electric Bolt

Txuas rau Magnetic Lock

Txuas rau Hluav Taws Xob Strike

Qhov Rooj Qhib Ntev Ntev Tswb Wiring Method (External Door Sensor)

Tamper-Switch Alarm Wiring Method
(Txuas mus rau Central Monitoring System los ntawm Modbus ntawm Universal I / O Module)

Tamper-Switch Alarm Wiring Method
(WG Port Door Sensor Wiring Method)

※ Kev Tiv Thaiv Kev Pabcuam "Qhia Qhov Rooj Relay" (Teeb tsa los ntawm kev teeb tsa qhov rai ntawm 701ServerSQL)

Ua kom muaj kev ruaj ntseg nrog AR-721RB

※ Txoj kev txuas no tsis tsim nyog rau "Qhia Qhov Rooj Relay" muaj nuj nqi (teeb tsa los ntawm kev teeb tsa parameter ntawm 701ServerSQL). Yog tias muaj cov kab hluav taws xob sab nraud rau Wiegand nyeem ntawv, WG Chaw nres nkoj yuav tsum ua kom Digital Relay Output kom pab "Qhia Qhov Rooj Relay" muaj nuj nqi.

Txuas rau Reader
(Txuas txuas lub LED sab nraud raws li lub teeb nraub qaum yuav tsum tau hloov kho tshwj xeeb firmware thiab WG qhev hom yuav raug kaw.)

※ Kev Tiv Thaiv Kev Tiv Thaiv "Qhia Qhov Rooj Relay" (Teeb tsa ntawm qhov tsis teeb tsa Qhov rai ntawm 701ServerSQL

AR-837-EA ua WG hom
(28 Nws 000 )

1. Thaum AR-837-EA dhau los ua WG hom, nws tuaj yeem siv nrog txhua tus tswj hwm.
2. Ob AR-837-EA tuaj yeem raug cais raws li Master thiab WG qhev nyeem rau Anti-pass rov qab nkag nkag thiab tawm.
   ※ Siv Txoj Cai:
   Kev lees paub lub ntsej muag rau ob qho tib si nkag thiab tawm: Ob leeg AR-837-EA Master hom thiab AR-837-EA WG qhev hom yuav tsum tau muab khaws cia tag nrho tib lub ntsej muag cov ntaub ntawv thiab tus lej tiag lossis pom daim npav. Daim npav: tuaj yeem hla WG cov lus rau tus maub los.
3. Thaum nkag mus rau qhov Parameter Teeb Qhov rai ntawm 701Server, lub cuab yeej tuaj yeem hloov mus rau WG qhev hom los ntawm Kev Ua Haujlwm "Ev5 WG tawm / Hv3 Lift out" Option.

Programming

A. Keyboard Xauv / Xauv

• Xauv / Xauv
  Xovxwm thiab ib txhij xauv cov keyboard. Nias ib txhij dua los qhib.

B. Nkag mus thiab tawm qhov programming hom

• Nkag mus
  Tswv yim *123456 # os * PPPPPP #
  [piv txwv li] Tus Nqi Default = 123456. Yog tias twb tau hloov pauv Master Code = 876112, cov tswv yim * 876112 # →Nkag mus rau programming hom PSYog tsis muaj kev qhia nkag rau hauv 30 sec, nws yuav cia li tawm hauv lub programming hom.
• Tawm Nias lub * * pheej 6 Tawm los yog 7 Tawm thiab Arming (Thov xa mus rau lub tswb / arming teeb tsa)
• Hloov cov Xib Hwb Code
  Nkag mus rau qhov programming hom → 5 "Cov cuab yeej 2paster Code → Nkag mus rau 6 tus lej tshiab tus lej lej → Ua tiav

C. Kev teeb tsa thawj zaug

• Kev teeb tsa lus
  Nkag mus rau lub programming hom → 5 Cov cuab yeej → 1 Lus → 0 EN → Ua tiav → Pib qhov system…
• Node ID ntawm Reader Setting
  Nkag mus rau qhov programming hom — 3 Parameters[1] → 1 Node ID → Input Tshiab Node ID: 1-254 (default value:001) → Lub Qhov Rooj Loj: 0-255 —0 WG1 Door Number : 0-255-0 Qhia UID (0=No, 1=WG, 2=ABA, 3=HEX) → Enable DHCP(O:No, 1:En, 2=Exit) → Ua tiav

Function Description of Front Panel & Indicator

1. Lub kaw lus yuav cia li tawm Programming hom thaum inactivating rau 30 vib nas this.
2. LED xwm txheej qhia txog tus maub los hom thiab xwm txheej.
   OK (ntsuab) – blinking tas li thaum khiav hauv Programming hom
   - lossis flashing ib daim npav uas muaj nyob hauv daim npav kawm hom, nws los 2 beeps ceeb toom thiab LCD vaj huam sib luag qhia "Tib daim npav: tus neeg siv chaw nyob / daim npav tus lej"
   Kev ua yuam kev (liab) - daim npav tsis raug nrog 2 beeps ceeb toom thiab LCD vaj huam sib luag qhia "Daim npav tsis raug!"
   - lossis nyob rau hauv hom kev tiv thaiv kev hla rov qab, thaum ua txhaum txoj cai nkag, nws los txog ib lub suab ceeb toom, thiab lub LCD vaj huam sib luag qhia "Anti-pass yuam kev!" Arming (ntsuab) – arming on status Alarm (liab)
   – tej yam txawv txav tshwm sim
3. Lub keypad yuav kaw rau 30 sec. thaum tsis raug tus lej PIN lossis tus lej lej nkag mus tas li.
4. Qhov kev ua yuam kev siab tshaj plaws ntawm tus lej lej thiab tus lej lej tuaj yeem hloov pauv ntawm software 701Server (default: 5 zaug)

Networking: / thiab sib tham sib flash ntawm lub hli thiab HNUB.
[eg] 12/07← → 12 07
Stand-alone: ​​Tsis flashing [piv txwv li] 12/07 (←Reference to picture)

Tsob Ntoo Manu

1. Ntxiv/Delete
   1. Ntxiv> Daim npav ID
   2. Ntxiv > RF Kawm
   3. Ncua> Chaw Nyob
   4. Ncua tseg > ID #
   5. Rho tawm> Chaw nyob
   6. Rho tawm> ID #
   7. Rov qab> Chaw Nyob
   8. Rov qab> ID #
   9. Antipass Group
2. Tus neeg siv teeb tsa
   1. Tus password
   2. Nkag mus rau hom
   3. Ntxiv kev xaiv
   4. Ib Pem Teb
   5. Ntau pem teb
   6. Sau npe ntsej muag
   7. Rho tawm ntsej muag
3. Parameters [1]
   1. Node ID
   2. OnOff OpenZone
   3. Qhov Rooj Relay Tm
   4. Qhov Rooj Kaw Tm
   5. Tswb Relay Tm
   6. Tswb Delay Tm
   7. Arming Delay Tm
   8. Arming PWD
4. Parameters [2]
   1. Nws pib Relock
   2. Egress (RTE)
   3. Lwm yam
   4. Force Qhib
   5. Kaw & Nres
   6. Anti-pass-rov qab
   7. Duress Code
   8. Tus password hom
   9. Hoobkas Rov pib dua
5. Cov cuab yeej
   1. Lus
   2. Master Code
   3. Master Range
   4. Terminal RS-485
   5. Ext.Comm CN11
   6. Qhib Sijhawm Sijhawm
   7. Cov ntaub ntawv
   8. Moos Teeb
   9. Lub Tswb Txhua Hnub
   0. UART Chaw nres nkoj CN9
6. Tawm
   
7. Tawm & Arming
   

D. Ntxiv thiab rho tawm Tag

※ Tus neeg siv muaj peev xwm: 16384 (00000 ~ 16383)

• Ntxiv Tag by Tag ID
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 1 Ntxiv -> Daim npav ID → Nkag mus 5-tus neeg siv qhov chaw nyob → Nkag Mus Rau Qhov Chaw Code → Nkag Nkag Daim Npav Code
• Ntxiv Tag los ntawm RF Kawm Function
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 2 Ntxiv -> RF-Learn → Nkag mus 5-tus neeg siv qhov chaw nyob
  → Input Tag Units(pcs) → Kaw Tag hauv RF Area
  ※ Yog batch ntawm tags yog Sequential, input Tag Units (pcs) nyob rau hauv kom muaj nuj nqis tags thiab nthuav tawm cov tag nrog tus lej qis tshaj rau tus maub los ntxiv rau tag nrho cov tag cov ntaub ntawv; txwv tsis pub, cov tags yuav tsum tau nthuav tawm rau tus tswj tus kheej
• Suspend User Address
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 2 Ncua tseg -> Addr → Input Start chaw nyob → Input End chaw nyob
• Ncua tseg Tag by Tag ID
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 4 Suspend -> ID # → Input Site Code → Input Card Code
• Rov qab User Address
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 7 Rho tawm -> Addr → Input Start chaw nyob → Input End chaw nyob
• Rov qab Tag by Tag ID
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 8 Rho tawm -> ID # → Input Site Code → Input Card Code
• Rho tawm Tus Neeg Siv Chaw Nyob
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 5 Rho tawm -> Addr → Input Start chaw nyob → Input End chaw nyob
• Kev rho tawm Tag by Tag ID
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 6 Rho tawm -> ID # → Input Site Code → Input Card Code
• Kev teeb tsa hom nkag
  Nkag mus rau programming hom → 2 Tus neeg siv Setting → 2 Nkag mus hom → Nkag Nkag Tus Neeg Siv Chaw Nyob → 0: Tsis raug; 1: Daim npav; 2: Daim npav lossis PIN; 3: Card & PIN

E. PIN Code

Nkag mus rau programming hom → 2 Tus neeg siv Setting → 1 Sau npe Face → Nkag mus 5-tus neeg siv chaw nyob → Nkag 4 tus lej PIN (0001 ~ 9999) → Ua tiav Los yog ntawm 701Client teeb nws ntawm cov neeg siv tshuaj ntsuam

F. Sau npe/Delete Face

• Ntxiv
  Nkag mus rau programming hom → 2 Tus neeg siv Setting → 6 Rho tawm ntsej muag → Ntsiab nyob rau hauv 5-tus neeg siv chaw nyob → Ua raws li cov lus qhia ntawm LCD npo rau npe rau lub ntsej muag → Ua tiav
• Kev rho tawm
  Nkag mus rau programming hom → 2 Tus neeg siv Setting → 7 Rho tawm FP → Tus yuam sij hauv 5-tus neeg siv chaw nyob → Ua tiav PS Yog xav rho tawm tag nrho cov neeg siv lub ntsej muag cov ntaub ntawv FP, qhov tseem ceeb hauv 99999 #

G. Nkag mus rau hom

Nkag mus rau programming hom → 2 Tus neeg siv teeb tsa
→ 2 Nkag mus rau hom
→ Key nyob rau hauv 5-tus neeg siv chaw nyob (00000 ~ 08999)
→ 0: Tsis raug; 1: Daim npav; 2: Daim npav lossis PIN; 3: Daim npav thiab PIN (837-EA: → Face Identify: 0: Yuav tsum; 1: Tsis quav ntsej)
→ Ua tiav

Nkag mus rau hom		Face Identify (837-EA nkaus xwb)		Cov txiaj ntsig (837-EA nkaus xwb)
Kho vajtse	701 Cov neeg siv khoom	Kho vajtse	701 Cov neeg siv khoom
0: Invalid		0: yuav tsum	Tsuas yog ntsej muag Tsuas yog daim npav tswj	Tus neeg siv tsis raug
		1: Tsis quav ntsej	Tsuas yog ntsej muag Tsuas yog daim npav tswj
1:kab		0: yuav tsum	Tsuas yog ntsej muag Tsuas yog daim npav tswj	Ntsej muag + Daim npav
		1: Tsis quav ntsej	Tsuas yog ntsej muag Tsuas yog daim npav tswj	1. Daim npav nkaus xwb 2. Lub ntsej muag nkaus xwb
2: Daim npav lossis PIN		0: yuav tsum	Tsuas yog ntsej muag Tsuas yog daim npav tswj	1. Ntsej muag + Daim npav 2.Face + PIN 3. Daim npav + ntsej muag + PIN 4. Daim npav + ntsej muag + Daim npav 5.PIN + Face + PIN 6.PIN + ntsej muag + Daim npav
		1: Tsis quav ntsej	Tsuas yog ntsej muag Tsuas yog daim npav tswj	1. Daim npav nkaus xwb 2. PIN nkaus xwb 3. Lub ntsej muag nkaus xwb
3: Daim npav thiab PIN		0: yuav tsum	Tsuas yog ntsej muag Tsuas yog daim npav tswj	Ntsej muag + Daim npav + PIN
		1: Tsis quav ntsej	Tsuas yog ntsej muag Tsuas yog daim npav tswj	1.Card + PIN 2.Face + PIN

H. Arming Password

Nkag mus rau programming hom → 3 Parameters[1] → 8 Arming PWD → Nkag mus 4 tus lej PIN (0001-9999; Default: 1234) → Ua tiav Los yog ntawm 701Server thiab teeb tsa ntawm AR-829E npo

I. Ncua Sijhawm Ncua Sijhawm

Nkag mus rau programming hom → 3 Parameters[1] → 7 ArmingDelayTm → Nkag mus armed sta. Lub sijhawm ncua sijhawm (Sec), Ntau Yam: 000 ~ 255; Armed mem tes tawm lub sij hawm (10ms), Range, 000 ~ 255 → Ua tiav

J. Duress Code

Nkag mus rau programming hom → 4 Parameters[2] → 7 Duress Code → 4 teeb (xaiv ib qho) → Nkag 4 tus lej PIN (0001 ~ 9999) → Ua tiav Los yog ntawm 701Server los teeb tsa ntawm AR-829E-V5 npo
※ Duress Code tsuas yog muaj nyob rau hauv hom kev sib txuas. Nws yuav hloov tus lej PIN tus kheej thiab xa cov lus ntawm Duress mus rau lub khoos phis tawj ua lub cim ceeb toom.

K. Terminal Chaw nres nkoj

Nkag mus rau programming hom → 5 Cov cuab yeej → 4 Terminal Chaw nres nkoj → 0: nqa; 1: Tus Tswv; 2: LED; 3: PRN (default value: 1) → Baud Selection (default value: 9600) → Succeeded

L. Teem lub tswb/arming

Cov xwm txheej:

1. Arming enabled
2. Alarm system txuas

Cov xwm txheej:

1. Lub qhov rooj qhib lub sijhawm: Lub qhov rooj qhib ntev dua qhov rooj relay lub sij hawm ntxiv rau lub qhov rooj kaw.
2. quab yuam qhib (Qhib yam tsis muaj daim npav siv tau): Kev nkag los ntawm kev quab yuam lossis kev ua txhaum cai.
3. Lub qhov rooj txoj hauj lwm yog txawv txav: Muaj tshwm sim thaum lub hwj chim tawm thiab rov qab dua, dua li, tus nyeem ntawv tau nyob rau hauv arming ua ntej lub hwj chim tawm.

Enable/Disable the arming status:

※ [Siv FP] tuaj yeem hloov pauv rau [Induct valid card].

M. Anti-pass-rov qab

Thaum txuas nrog AR-721-U, AR-737-H / U (WG hom), thiab AR-661-U rau kev tiv thaiv kev hla rov qab, hom kev nkag yuav tsum yog "Daim npav" nkaus xwb.

• Device enables
  Nkag mus rau programming hom → 4 Parameters[2] → 6 Anti-pass-rov qab → tus tswv tswj xaiv [1: Yog] → WG xaiv [1: Yog]
• Cov neeg siv daim npav ua haujlwm
  Nkag mus rau programming hom → 1 Ntxiv/Delete → 9 Antipass Group → Nkag mus 5 tus lej pib tus neeg siv chaw nyob → Nkag 5 tus lej xaus tus neeg siv qhov chaw nyob → yuav tsum xaiv [1: Yog]

N. Lift tswj

[xws li] Txuas nrog AR-401-IO-0016R los tswj cov pem teb twg tus neeg siv yuav nkag tau. (BAUD 9600)

Teem Lift Control
Nkag mus rau programming hom → 5 Cov cuab yeej → 4 Terminal Chaw nres nkoj → 0: Lift Controller → Baud Xaiv 0: 9600
Nkag mus rau programming hom → 5 Cov cuab yeej → 5 Terminal Chaw nres nkoj → 1: Lift Controller
(yuav tsum siv AR-321L485-5V)

Ib pem teb
Nkag mus rau programming hom → 2 Tus neeg siv Setting → 4 Ib Pem Teb → Cov tswv yim 5-tus neeg siv qhov chaw nyob → Nkag mus rau ib tus lej hauv pem teb: 1 ~ 64

Ntau pem teb
Nkag mus rau programming hom → 2 Tus neeg siv teeb tsa → 5 Multi Floor → Cov tswv yim 5-tus neeg siv qhov chaw nyob → Xaiv ntau yam: 1 lossis 2 lossis 3 lossis 4 → Nkag 16 tus lej ntau pem teb tooj [0: disable, 1: pab]
[eg] Teem NO. 114, siv tau los ntawm 8 F thiab 16F:
Nkag mus rau programming hom → 2 Tus neeg siv Setting → 5 Multi Floor → 114 → 1 → 0000000100000001

O. Lub tswb moos (rau lub Hoobkas)

Nkag mus rau programming hom → 5 Cov cuab yeej → 9 Lub tswb txhua hnub → Teeb (00 ~ 15) → Teem Pib Tm (24 Teev); Teeb nyhuv Sec.
(Seconds raws li lub tswb lub sij hawm, Range: 1 ~ 255) → Teem lub lim tiam (0: disable, 1: pab) → Ua tiav

Kho vajtse installation

P. OpenZone

Nkag mus rau programming hom → 3 Parameters[1] → 2 Qhib OpenZone → Main Controller Auto Open Zone (0: lov tes taw, 1: pab) → Qhib Qhov Rooj mm. Thaum Lub Sij Hawm Qhib (0: Tsis yog, 1: Yog) → WG1 Chaw nres nkoj pib qhib Zone (0: lov tes taw, 1: pab) → Qhib Qhov Rooj Imm. Qhib Zone (0: Tsis yog, 1: Yog) → Ua tiav

Q. Qhib TimeZone

Nkag mus rau programming hom → 5 Cov cuab yeej → 6 Qhib TimeZone → Teem (00 ~ 15) → Sijhawm (24 Teev) → Chaw nres nkoj loj (0: lov tes taw, 1: pab); WG Port(0:disable,1:enable) → Weekday(0:disable,1:enable) →Ua tiav

Parameter Setting Menu

IP Chaw Nyob Config

Nkag mus rau lub programming hom → 3 Parameters[1] → 1 Node ID → Nkag mus rau Node ID tshiab → Main Qhov Rooj Number Range → WG1 Qhov Rooj Number Range → Qhia WG Message → Qhib DHCP → thov nkag IP Chaw Nyob (IPV4) → thov nkag Net Mask (IPV4 ) → thov nkag mus rau Gatewa(IPV4) → Ua tiav

Teem daim npav tso saib hom

Nkag mus rau programming hom → 3 Parameters[1] → 9 PIN & UID hom → Tus neeg siv tus PIN Length → Daim npav UID Length → Qhia UID → Ua tiav

Lub ntsej muag rau npe

• Lub ntsej muag yuav tsum nyob ze ntawm lub vijtsam LCD, qhov loj ntawm lub ntsej muag duab yog ib nrab ntawm lub LCD uas yuav yooj yim dua rau kev sau npe ua tiav
  
• Cov txheej txheem rau npe nkag

Cov Lus Qhia thiab Cov Lus Qhia rau Kev Sau Npe thiab Kev Pom Zoo ntawm Kev Tiv Thaiv Kev Tiv Thaiv Kev Tiv Thaiv Lub ntsej muag

(—) Thaum sau npe cov ntaub ntawv ntsej muag, lub ntsej muag tsis tuaj yeem hnav.
Sau lub ntsej muag nta

(=) Kev teeb tsa qib kev ruaj ntseg ntawm lub ntsej muag tswj mus rau [Level Low] yuav pab kom pom lub ntsej muag lub ntsej muag hom

(=) Hais txog 3D qauv paub thiab sim sau ntau cov duab nyob ib ncig ntawm lub qhov muag thaum sau npe cov ntaub ntawv ntsej muag.

Cov ntaub ntawv / Cov ntaub ntawv

SOYAL AR-837-EA Graphic Display Multi-Function Proximity Controller [ua pdf] Phau ntawv qhia AR-837-EA, Graphic Display Multi-Function Proximity Controller, AR-837-EA Graphic Display Multi-Function Proximity Controller

Cov ntaub ntawv

• Cov neeg siv phau ntawv