Moxa - Your Trusted Partner in AutomationMoxa - Your Trusted Partner in AutomationMoxa - Support
Installation Guide for MOXA models including: MGate 5135 Series, MGate 5435 Series, Modbus TCP Gateways, MGate 5135 5435 Series Modbus TCP Gateways, MGate 5135 Series Modbus TCP Gateways, MGate 5435 Series Modbus TCP Gateways
MGate 5135-T: 1-портовый преобразователь Modbus RTU/ASCII/TCP в EtherNet/IP, с расширенным диапазоном температур, Moxa
MGate 5135: 1-поÑÑовÑй пÑеобÑазоваÑÐµÐ»Ñ Modbus RTU/ASCII/TCP в EtherNet/IP, Moxa
MGate 5135/5435 Series - Modbus TCP Gateways | MOXA
File Info : application/pdf, 6 Pages, 2.50MB
DocumentDocumentMGate 5135/5435 Series Quick Installation Guide Version 1.0, September 2022 Technical Support Contact Information www.moxa.com/support 2022 Moxa Inc. All rights reserved. P/N: 1802051350010 *1802051350010* Overview The MGate 5135/5435 is an industrial Ethernet gateway for Modbus RTU/ASCII/TCP and EtherNet/IP network communications. Package Checklist Before installing the MGate 5135/5435, verify that the package contains the following items: · 1 MGate 5135 or MGate 5435 gateway · Quick installation guide (printed) · Warranty card NOTE Please notify your sales representative if any of the above items are missing or damaged. Optional Accessories (can be purchased separately) · Mini DB9F-to-TB: DB9 female to terminal block connector · WK-25: Wall-mounting kit, 2 plates, 4 screws, 25 x 43 x 2 mm Hardware Introduction LED Indicators LED PWR 1, PWR 2 Color Green Off Off Green Ready Red EtherNet/IP Adapter Off Green Red Off Green Modbus RTU/ASCII/TCP Client Red Description Power is on. Power is off. Power is off. Steady: Power is on, and the MGate is functioning normally. Blinking (1 sec.): The MGate has been located by the MGate Manager's Location function. Steady: Power is on, and the MGate is booting up. Blinking (0.5 sec.): Indicates an IP conflict, or the DHCP or BOOTP server is not responding properly. Blinking (0.1 sec.): the microSD card failed. No connection has been established. Steady: I/O data is being exchanged with all of the connections. Steady: Rejects the connection due to incorrect configurations. Blinking (1 sec.): One or more connections timed out. No communication with Modbus device. Modbus communication in progress. Blinking (1 sec.):Communication error. 1. The Modbus slave device returned an error (exception). 2. Received a frame error (parity error, checksum error). 3. Timeout (the slave device does not respond). - 2 - LED ETH 1, ETH 2 Color Green Amber Off Description 4. TCP connection failed (only for Modbus TCP). Steady ON: Ethernet link on at 100Mbps. Blinking: Data transmitting at 100Mbps. Steady ON: Ethernet link on at 10Mbps. Blinking: Data transmitting at 10Mbps. Ethernet is not connected. Dimensions MGate 5135 MGate 5435 Reset Button Restore the MGate to factory default settings by using a pointed object (such as a straightened paper clip) to hold the reset button down until the Ready LED stops blinking (approx. five seconds). - 3 - Hardware Installation Procedure 1. Connect the power adapter. Connect the 12 to 48 VDC power line or DIN-rail power supply to the terminal block of the MGate 5135/5435 device. 2. Use a Modbus serial cable to connect the MGate to a Modbus slave device. 3. Use an Ethernet cable to connect the MGate to the EtherNet/IP controller. 4. We designed the MGate 5135/5435 to attach to a DIN rail or mounted on a wall. For DIN-rail mounting, push down the spring and properly attach it to the DIN rail until it "snaps" into place. For wall mounting, install the wall-mount kit (optional) first and then screw the device onto the wall. The following figure illustrates the two mounting options: Wall- or Cabinet-mounting We provide two metal plates for mounting the unit on a wall or inside a cabinet. Attach the plates to the unit's rear panel with screws. With the plates attached, use screws to mount the unit on a wall. The heads of the screws should be 5 to 7 mm in diameter, the shafts should be 3 to 4 mm in diameter, and the length of the screws should be over 10.5 mm. Software Installation Information Please download the User Manual and Device Search Utility (DSU) from Moxa's website: www.moxa.com Refer to the User's Manual for additional details on using the DSU. The MGate 5135/5435 also supports login via a web browser. Default IP address: 192.168.127.254 Create your administration account and password when you log in the first time. - 4 - Pin Assignments Modbus Serial Port (Male DB9) Pin RS-232 1 DCD 2 RXD 3 TXD 4 DTR 5* GND 6 DSR 7 RTS 8 CTS 9 *Signal ground RS-422/ RS-485 (4W) TxD-(A) TxD+(B) RxD+(B) RxD-(A) GND RS-485 (2W) Data+(B) Data-(A) GND Ethernet Port (RJ45) Pin Signal 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- Power Input and Relay Output Pinouts V2+ V2- V1+ V1- DC Power Input 2 DC Power Input 2 N.O. Common N.C. DC Power Input 1 DC Power Input 1 Specifications Power Parameters Power Input 12 to 48 VDC Power Consumption MGate 5135 Series: 455 mA max. MGate 5435 Series: 455 mA max. Relays Contact Current Rating Resistive load: 2 A @ 30 VDC Environmental Limits Operating Standard models: -10 to 60°C (14 to 140°F) Temperature Wide temp. models: -40 to 75°C (-40 to 167°F) Storage Temperature -40 to 85°C (-40 to 185°F) (package included) Ambient Relative 5 to 95% RH Humidity Physical Characteristics Dimensions MGate 5135 Series: 25 x 90 x 129.6 mm (0.98 x 3.54 x 5.1 in) MGate 5435 Series: 42 x 90 x 129.6 mm (1.65 x 3.54 x 5.1 in) - 5 - Weight Reliability Alert Tools MTBF MGate 5135 Series: 294 g (0.65 lb) MGate 5435 Series: 403 g (0.89 lb) Built-in buzzer and RTC MGate 5135 Series: 1,240,821 hrs. MGate 5435 Series: 689,989 hrs. ATTENTION Power terminal plug wiring size is 28-14 AWG, tighten to 1.7 in-lbs, wire Min. 80°C, Use copper conductors only. Hot Surface Label. Functional earth terminal. ATTENTION · This device is an open-type equipment and intended to be installed in a suitable enclosure. · If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. · When installing, the assembler is responsible for the safety of the system in which the equipment is incorporated. NOTE · · This device is intended for use indoors and at altitudes up to 2,000 meters. Pollution degree 2. NOTE Clean the device with a soft cloth, dry or with water. NOTE The power input specification complies with the requirements of SELV (Safety Extra Low Voltage), and the power supply should comply with UL 61010-1 and UL 61010-2-201. For any repair or maintenance needs, please contact us. Moxa Inc. No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004, Taiwan +886-03-2737575 - 6 -