Super Bright LEDs LHBDSA Series User Manual

Product Information

Model Numbers Covered: LHBDSA-SW2B320-WHMBL, LHBDSA-SW2BS320-WHMBL

Safety and Notes

⚠️ WARNING

• To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. Commercial installation, service, and maintenance of luminaires should be performed by a qualified, licensed electrician. For installation, if you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Use an appropriate strain relief bushing when connecting the supply cord/conduit to the driver box.
• Turn off electrical power at fuse or circuit breaker box before wiring fixture to supply power.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information before applying power.
• All wiring connections should be capped with UL/ETL approved wire connectors.

⚠️ CAUTION

• Avoid direct eye exposure to the light source while it is on.
• Risk of burn. Disconnect power and allow fixture to cool before handling fixture.
• Proper earth grounding is required to ensure safety.
• Please turn off the power before installation or maintenance.
• Do not use any electric generator to test the LED light.

ℹ️ NOTICE

• Minimum 90° supply conductors.
• Suitable for dry or damp location.

Wiring Diagram

The wiring diagram illustrates connections for a 120-277 VAC input. It shows:

• Line: Connected to the Black wire.
• Neutral: Connected to the White wire.
• Ground: Connected to the Green wire.
• 0-10 V Dimming: Dim (+) connected to the Purple wire, Dim (-) connected to the Gray/Pink wire.

Please check the product label for specific electrical specifications related to installation. Improper installation will void the warranty.

Optional Accessories

• Pendant mount for LHBDSA-SW2B165-WHMBL (LHBDSA-PM1)
• Pendant mount for LHBDSA-SW2B320-WHMBL and LHBDSA-SW2B600-WHMBL (LHBDSA-PM2)

CCT and Wattage Selection

Use the two switches located on the top of the light to select the desired CCT (Correlated Color Temperature) and wattage. Controls include "Wattage Selection" and "CCT Selection".

Motion Sensor Compatibility

For LHBDSA-SW2B165-WHMBL, LHBDSA-SW2B320-WHMBL, LHBDSA-SW2B600-WHMBL:

These models use 3-pinned connection motion sensors.

• HBR3-MS (microwave sensor)

For LHBDSA-SW2BS165-WHMBL, LHBDSA-SW2BS320-WHMBL:

These models use 3.5mm jack connection motion sensors.

• EFS106-AUX (PIR sensor)
• ANT-5-4T (microwave sensor)

Installation

Suspension Installation

1. Switch off breaker to remove supply power.
2. Attach chains to a pipe or mounting hooks (not included) that can support the weight of the fixture.
3. Select desired CCT and wattage.
4. Attach hangers to chain and hang light. Adjust height as needed.
5. Connect wiring and conduit to fixture.

[Diagram illustrating suspension installation]

Pendant Installation (optional)

1. Switch off breaker to remove supply power.
2. With side access panels removed, attach pendant mount to pipe. Note: make sure the pipe will be able to support the weight of the fixture prior to installation.
3. Select desired CCT and wattage.
4. Attach light to mount.
5. Connect wiring.
6. Install the side access panels on the mounting bracket.

[Diagram illustrating pendant installation]