Logosol User Manual - Loncin 15HP

Part No. 0458-395-5431 | REV: 1

Introduction

Read through the user manual carefully and make sure you understand its contents before using the saw.

WARNING! Incorrect use can result in serious or fatal injuries to the operator or others.

Assembly Instructions

  1. Step 1: Mounting Components

    Attach components using the following hardware:

    • 2 x M6x25 screws
    • 2 x M6x30 screws
    • 2 x unspecified components

    Ensure a 12mm and 10mm clearance as indicated in the diagram.

  2. Step 2: Throttle Wire Connection

    Connect the throttle wire and sheath as shown in the diagram. This involves two '1st' components.

  3. Step 3: Exhaust Reflector Installation

    Mount the exhaust reflector on the exhaust pipe using 4 x RXS 4.2x9.5 screws.

  4. Step 4: Further Component Mounting

    Mount additional components using:

    • 4 x M10x40 screws
    • 4 x M10 screws
    • 4 x M10 screws
  5. Step 5: Pulley and Housing Installation

    Install the pulley and housing using the following hardware:

    • 1 x M8x24x2 screw
    • 1 x SRKB 12.5x35x2 screw
    • 4 x unspecified components
    • 1 x 03-02053 component
  6. Step 6: Throttle Wire Assembly Preparation

    Begin the throttle wire assembly by removing the airbox filter and the lower part of the airbox.

  7. Step 7: Throttle Cable Attachment

    Attach the throttle cable in the bracket (1). Connect the end of the cable to the throttle control (2). Then, untighten the nut holding the throttle control (3) to ensure the throttle can return easily.

  8. Step 8: Voltage Regulator and Battery Connection

    Mount the voltage regulator onto the battery box (1). Connect the red cable with the fuse holder to the solenoid (2). Connect the cable between the positive terminal of the battery and the solenoid (3). Finally, connect the cable between the negative terminal of the battery and the engine chassis (4).

    • Hardware used: 2 x M6x25 screws, 2 x M6 screws
  9. Step 9: Safety Switch Connection

    Connect the safety switch. The connector must be attached to the divisible connector in the cable kit (1). Couple the joint piece and connect the switch. Then, couple the ring cable lug to the motor chassis (2).

Safety Switch Wiring Diagram

The wiring diagram illustrates the connections for the safety switch. Key components include the safety switch itself (Elesa CFSQ, 60-SH-6-FAS-2), a joint coupling, and connections for 'Ignition off' and 'Ignition off' states, with color-coded wires (Blue, Grey, Black).

Models: LONCIN 15HP, Gasoline Engine

PDF preview unavailable. Download the PDF instead.

loncin 15hp user manual Adobe PDF Library 16.0.3 Adobe InDesign 17.0 (Macintosh)

Related Documents

Preview Logosol 15 HP Loncin Petrol Engine User Manual - Installation Guide
Comprehensive user manual detailing the installation of the Loncin 15 HP petrol engine for Logosol band sawmills. Covers assembly steps, throttle adjustment, electrical connections, and safety warnings.
Preview Logosol 4.6 kW Electric Motor User Manual
User manual for the installation of the Logosol 4.6 kW electric motor for band sawmills. Includes setup instructions and important notes for correct functioning.
Preview Logosol 13.5 HP Briggs & Stratton Petrol Engine Installation Manual
Installation guide for the Logosol band sawmill, detailing the setup of the 13.5 HP Briggs & Stratton petrol engine, including assembly, throttle adjustment, and safety switch connection.
Preview LOGOSOL B701 Bruksanvisning: Montering, Drift och Säkerhet
En komplett bruksanvisning för LOGOSOL B701 bandsågsverk. Innehåller detaljerade instruktioner för montering, säkerhetsföreskrifter, drift, underhåll och felsökning för optimal prestanda.
Preview LOGOSOL E25 Feeding User Manual
Comprehensive user manual for the LOGOSOL E25 Electric Feed Unit, covering installation, operation, maintenance, and troubleshooting. Includes part lists, diagrams, and wiring information.
Preview Logosol 13.5 HP Briggs & Stratton Engine User Manual
User manual for the installation of the 13.5 HP Briggs & Stratton petrol engine for the Logosol band sawmill. Includes assembly instructions, throttle adjustment, and safety switch wiring.
Preview Logosol ES5/ES8 Elektrisk Kedjesåg Bruksanvisning
Denna bruksanvisning ger detaljerade instruktioner för Logosol ES5/ES8 elektrisk kedjesåg, inklusive säkerhetsföreskrifter, maskinbeskrivning, tekniska data, montering, funktioner, felsökning och underhåll.
Preview Logosol 13.5 HP Briggs & Stratton Engine Installation Guide
Step-by-step installation manual for fitting a 13.5 HP Briggs & Stratton engine to a Logosol bandsawmill. Includes assembly, adjustments, and safety instructions.