Instruction Manual for NISSAN models including: Ariya FE0, T99G6 5MP00, T99F3 5MP00, T99F6 4RA0A, T99G6 5MP00 Illuminated Kick Plate Kit, T99G6 5MP00, Illuminated Kick Plate Kit, Kick Plate Kit, Plate Kit
a ) a ) b ) a ) b ) Allow 3 min after key off with doors closed for vehicle power to time out. 05102024 Nissan North America Page 6 of 50 2.3) Disconnect battery terminal
File Info : application/pdf, 50 Pages, 2.76MB
DocumentDocumentGENUINE PARTS Illum inat ed Kick Plat e Kit Installation Manual Ariya FE0 T99G6 5MP0 0 Nissan North Am erica 0 510 20 24 Page 1 of 50 B D C A F G E H ADDITIONAL SERVICE PARTS NOT INCLUDED IN KIT ABOVE : It em Qt y. Part Descrip t io n AAA 2 Accessory Service Connect or AAA Nissan North Am erica J Service Part Nu m b er T99F6 4RA0 A 0 510 20 24 Page 2 of 50 PART NUMBER(S) REQUIRED FOR INSTALLATION: T99F3 5MP0 0 T99F6 4RA0 A , Accessory Service Connect or - not included in kit above KIT CONTENTS: It em Qt y. Part Descrip t io n Service Part Nu m b er A 1 Illum inat ed Kick Plat e, Front LH B 1 Illum inat ed Kick Plat e, Front RH C 1 Illum inat ed Kick Plat e, Rear LH D 1 Illum inat ed Kick Plat e, Rear RH E 16 Cable Tie, 150 m m Not ServiceablePart of Kit T99F3 5MP0 0 F 4 Posi-Tap Connect or G 4 Foam Tape, black, 25 x 25 x 1m m H 15 Foam Tape, gray, 90 x 60 x 5 m m J 1 Inst allat ion Inst ruct ion Websit e Address TOOLS REQUIRED: Rat chet , 1/ 4" drive Socket , 10 m m , 1/ 4" drive Torque Wrench, 1/ 4" drive Screwdriver, Flat 1/4" Screwdriver, Torx T20 INSTALLATION CAUTIONS: Trim Removal Tool, Nylon Pliers, Wire Cutting Electrical Tape Work Light 50% Alcohol/50% Water Solution Cloth, Soft Non-Linting Masking Tape CAUTION Dealer inst allat ion recom m ended. Inst ruct ions m ay refer t o Service Manual. Please read t his inst ruct ion carefully before inst alling t his product for correct inst allat ion . Please DO NOT use or inst all t he part in w ays ot her t han w hat is described . Alw ays use floor, seat and st eering w heel prot ect ion. Part s ut ilizing adhesion as m et hod of at t achm ent are t o be inst alled at surface t em perat ure of 15-38° C Posi-Tap inst ruct ions m ust be specifically follow ed as described in Appendix A. Apply m asking t ape as needed t o prot ect areas t hat m ay be scrat ched or dam aged by t ools. Alw ays rem ove vehicle part s in t he sequence direct ed. Im proper procedure can dam age part s. Take care not t o scrat ch or dam age any com ponent during t he rem oval or re-inst allat ion p r o c ess. Trim pieces found t o have w it ness m arks or broken clips ARE NOT t o be reinst alled . St ore rem oved part s in a safe m anner. If a problem occurs during inst allat ion, please cont act Nissan dealer w here product w as purchased. Nissan North Am erica 0 510 20 24 Page 3 of 50 1.1) SYSTEM Dealer-Option Connector PosiTap (F) Kick Plate, Front RH (B) I l l u m i n a t e d Kick Plate, Rear RH (D) I l l u m i n a t e d Vehicle Harness Accessory Service Connector (AAA) Rear IKP Harness Connector . Front of Vehicle . I l l u m i n a t e d Kick Plate, Front LH (A) 1.2) D-OPT CONNECTOR LOCATION I l l u m i n a t e d Kick Plate, Rear LH (C) Dealer-Opt ion Connect or Locat ions Nissan North Am erica 0 510 20 24 Page 4 of 50 CAUTION Alw ays record radio st at ions if disconnect ing Bat t ery t erm inal. 2.1) Record Cust om er Preset s a ) Place ignit ion in "ON" m ode. b ) Record t he cust om er radio preset s and ot her preset s as required. Preset 1 2 3 4 5 6 7 8 9 10 c ) Place ignit ion in "OFF" m ode. Nissan North Am erica 0 510 20 24 Page 5 of 50 2.2) Move seat s. a ) Move bot h front seat s t o full upw ard and rearw ard posit ion. 2.3) Disconnect bat t ery t erm inal a ) Locat e negat ive bat t ery t erm inal. b ) Loosen nut w it h 10 m m socket Bat t ery Term inal Nut CAUTION Allow 3 m in aft er key off w it h doors closed for vehicle pow er t o t im e out . 2.4) Disconnect bat t ery t erm inal a ) Lift negat ive bat t ery t erm inal off st ud. b ) Isolat e negat ive bat t ery t erm inal. CAUTION Allow 3 m in aft er negat ive t erm inal dis-connect before separat ing any elect rical connect ors. Nissan North Am erica 0 510 20 24 Page 6 of 50 Front of Vehicle 3.1) Inst all locat ion t em plat e on LH Front Door a ) Locat e LH inner sill plat e assem bly. 3.2) Rem ove LH t rim a b a ) Using t rim rem oval t ool at forw ard end of kick plat e, pry kick plat e up t o disengage clips. b ) Repeat at rearw ard end. 3.3) Rem ove LH t rim a ) Lift sill plat e up as show n t o rem ove. Nissan North Am erica 0 510 20 24 Page 7 of 50 3.4) Remove LH trim a ) Unfasten five (5) carpet loops from secondary sill trim. Carpet loop 3.5) Remove LH trim a ) Lift harness prot ect or up as show n t o rem ove. Front of Vehicle 3.6) Rem ove LH t rim a ) Place Masking Tape on out er door sill as show n. Line up forw ard edge of t ape w it h forw ard edge of clip holes in BPillar t rim . Nissan North Am erica 0 510 20 24 Page 8 of 50 3.7) Rem ove RH t rim b ) Repeat st eps 3.1t hrough 3.6 for RH side. 3.8) Rem ove LH t rim a ) Using t rim rem oval t ool, rem ove hood release handle by pulling aw ay from t rim panel. b ) Remove trim fastener from lower kick trim by unscrewing with flat screwdriver. c ) Disengage lower kick trim pawl by pulling toward interior of vehicle. Trim Fastener Pawl 3.9) Fo r 20 24 veh icle, skip t o St ep 3.14 Nissan North Am erica 0 510 20 24 Page 9 of 50 3.10 ) Rem ove LH t rim a ) Using t rim rem oval t ool, rem ove LH Dash Out er t rim . 3.11) Rem ove LH t rim a ) Rem ove Low er IP t rim by gent ly pulling t ow ard driver seat as show n. b ) Let Low er IP t rim hang dow n. 3.12) Locat e LH side D-Opt connect or a ) Locat e D-Opt Connect or t aped t o m ain harness bundle. b ) Using scissors, cut vinyl t ape affixing co n n ect o r. D-Opt Con nect o r Nissan North Am erica 0 510 20 24 Page 10 of 50 3.13) Locat e LH side D-Opt connect or a ) Gent ly pull D-Opt Connect or dow n t o proper locat ion as show n. D-Opt Con nect o r 3.14) Lo cat e LH sid e D- Op t co n n ect o r (20 24) a ) Locat e D-Opt Connect or t aped t o m ain harness bundle. D-Opt Con nect o r NOTE 20 24 vehicles only Nissan North Am erica 0 510 20 24 Page 11 of 50 Front of Vehicle 4.1) Remove RH Trim a ) Remove trim fastener from lower kick trim by unscrewing with flat screwdriver. b ) Disengage lower kick trim pawl by pulling toward interior of vehicle, as shown. Trim Fastener Pawl 4.2) Fo r 20 24 veh icle, skip t o St ep 4.10 4.3) Remove RH Trim a ) Using trim removal tool, remove RH Dash Outer trim. Nissan North Am erica 0 510 20 24 Page 12 of 50 4.4) Remove RH Trim a ) Remove nut from forward edge of Lower IP trim. Nut b ) Using Trim Removal Tool, release 4 pawls from rearward edge. Pawl c ) Remove Lower IP trim. 4.5) Remove RH Trim a ) Using Torx T20 screwdriver, remove lower 3 screws from Glove Box assembly. Sc r e w 4.6) Remove RH Trim a ) Using Torx T20 screwdriver, remove upper 3 screws from Glove Box assembly. Sc r e w Nissan North Am erica 0 510 20 24 Page 13 of 50 DISCONNECT 4.7) Remove RH Trim a ) Gently remove Glove Box assembly and tilt down. b ) Disconnect glove box lamp connector. c ) Remove harness edge biter clip off glove box. d ) Store glove box in a safe area. Glove Box Lamp Connector Biter Clip 4.8) Locat e RH side D-Opt connect or a ) Locat e D-Opt Connect or t aped t o m ain harness bundle. b ) Using scissors, cut vinyl t ape affixing co n n ect o r. D-Opt Con nect o r 4.9) Locat e RH side D-Opt connect or a ) Gent ly pull D-Opt Connect or dow n t o proper locat ion as show n. D-Opt Con nect o r Nissan North Am erica 0 510 20 24 Page 14 of 50 4.10 ) Locat e RH side D-Opt connect or (20 24) a ) Locat e D-Opt Connect or t aped t o m ain harness bundle. b ) Connect Accessory Service Connect or t o D-Opt Connect or D-Opt Con nect o r NOTE 20 24 vehicles only Nissan North Am erica 0 510 20 24 Page 15 of 50 5.1) Rem ove Rear LH t rim a ) Pull up on front low er edge of rear seat b ase. Front of Vehicle 5.2) Rem ove LH t rim a ) Place Masking Tape on out er door sill as show n. Line up rearw ard edge of t ape w it h forw ard edge of kick plat e. c b a 5.3) Rem ove Rear LH t rim a ) Using t rim rem oval t ool at forw ard end of inner kick plat e, pry up t o disengage clips t o B-pillar t rim . b ) Repeat at rearw ard end t o disengage clips t o rear pillar t rim and t rim clip as show n. Trim Clip b ) Rem ove kick plat e from vehicle. Nissan North Am erica 0 510 20 24 Page 16 of 50 5.4) Rem ove LH t rim a ) Using t rim rem oval t ool, disengage 2 low er clips of B-pillar t rim . Trim Clip b ) Do not rem ove ent ire t rim . Leave loose as show n. 5.5) Rem ove Rear RH t rim a ) Repeat st eps 5.2 t hrough 5.4 for t he Rear RH Trim . Nissan North Am erica 0 510 20 24 Page 17 of 50 CAUTION Th e Accesso ry Service Co n n ect o r is fo r u se ONLY w it h Gen u in e Nissan (o r In fin it i) o r Nissan (o r In fin it i) ap p ro ved accesso ries. Use o f t h is co n n ect o r w it h n o n Gen u in e Nissan (o r In fin it i) o r Nissan (o r In fin it i) ap p ro ved accesso ries o r failu re t o fo llo w t h e in st allat io n in st ru ct io n s fo r said connect or being m ent ioned herein m ay result in dam age t o t he accessory and/ or your vehicle. Nissan / In fin it i is n o t liab le fo r lo ss o r d am ag e d u e t o im p ro p er in st allat io n o r in st allat io n o f n o n Gen u in e o r n o n ap p ro ved accesso ries. Accessory Service Connector end (AAA) 6.1) Connect ASC (AAA) t o IKP, Front LH (A) a ) For det ailed direct ions, see Appendix A - Posi-Tap Procedure. b ) Addit ional circuit inform at ion is in Appendix B - Mechanizat ion Draw ing. 6.2) Connect ASC (AAA) t o IKP, Front LH (A) a ) Using a Posi-Tap (F), connect t he BLACK IKP lead w ire t o t he "ROOM_LAMP" (YELLOW w ire) of t he Harness (AA) as show n. b ) Using a Posi-Tap (F), connect t he RED IKP lead w ire t o t he "BAT_SAVER" (PINK w ire) of t he Harness (AA) as show n. Po si Tap (F) Nissan North Am erica 0 510 20 24 Page 18 of 50 6.3) Connect ASC (AAA) t o IKP, Front LH (A) a ) Once prepared as described in Appendix A, t he Accessory Harness w it h IKP at t ached should look like t his. 6.4) Connect ASC (AAA) t o IKP a ) Plug LH ASC int o LH D-Opt connect or. D-Opt Con nect o r b ) Connect harness from Illum inat ed Kick Plat e, Front LH (A) t o Illum inat ed Kick Plat e, Rear LH ( C) Nissan North Am erica 0 510 20 24 Page 19 of 50 6.5) Connect ASC (AAA) t o IKP a ) Place bot h IKPs on front carpet . 6.6) Connect ASC (AAA) t o IKP, Front RH (B) a ) Repeat st eps 6.1t hrough 6.5 for t he Illum inat ed Kick Plat e, Front RH (B). 6.7) Elect rical funct ion check a ) Re-connect negat ive bat t ery cable Nissan North Am erica 0 510 20 24 Page 20 of 50 ARIYA 6.8) Elect rical funct ion check b ) Close all doors. c ) Confirm all Illum inat ed Kick Plat es t urn OFF w hen Room Lam p t urns OFF. ARIYA 6.9) Elect rical funct ion check a ) Open front LH door. b ) Confirm all Illum inat ed Kick Plat es t urn Nissan North Am erica 6.10 ) Elect rical funct ion check a ) If NG, check fusing, harness rout ing, connect ions, and IKP t o ident ify root c a u se. CAUTION Wh en d iag n o sin g elect rical syst em problem s, first disconnect t he accesso ry co n n ect o r(s) an d n o t e effect o n veh icle syst em . Con t in u e t he invest igat ion w it h t he accessory co n n ect o r(s) d isco n n ect ed . Reco n n ect w h en t h e in vest ig at io n is com plet e. 0 510 20 24 Page 21 of 50 6.11) Disconnect ASC a ) Un-plug LH ASC from LH D-Opt co n n ect o r. b ) Disconnect harness from Illum inat ed Kick Plat e, Front LH (A) t o Illum inat ed Kick Plat e, Rear LH ( C). Nissan North Am erica 0 510 20 24 Page 22 of 50 6.12) Move seat s. a ) Move bot h front seat s t o full upw ard and forw ard posit ion. 6.13) Disconnect bat t ery t erm inal a ) Locat e negat ive bat t ery t erm inal. b ) Loosen nut w it h 10 m m socket . Bat t ery Term inal Nut CAUTION Allow 3 m in aft er key off w it h doors closed for vehicle pow er t o t im e out . 6.14) Disconnect bat t ery t erm inal a ) Lift negat ive bat t ery t erm inal off st ud. b ) Isolat e negat ive bat t ery t erm inal. CAUTION Allow 3 m in aft er negat ive t erm inal dis-connect before separat ing any elect rical connect ors. Nissan North Am erica 0 510 20 24 Page 23 of 50 Front of Vehicle 7.1) Clean LH door at t achm ent area a ) Wipe door sill area clean of any dirt . b ) Wipe using alcohol/ w at er solut ion on a soft non-lint ing clot h. c ) Let dry for 30 seconds. 21 7.2) Inst all LH Kick Plat e a ) Part ially peel aw ay enough of t he 2 adhesive liners t o fold dow n a "flag" t hat w ill ext end beyond t he out er edge of Illum inat ed Kick Plat e, Rear LH (B) as show n. 7.3) Inst all LH Kick Plat e a ) Posit ion Illum inat ed Kick Plat e, Rear LH (B) on door sill area, lining up forw ard edge of (B) w it h rear edge of m asking t ap e. a Nissan North Am erica 0 510 20 24 Page 24 of 50 7.4) Inst all LH Kick Plat e a ) Adjust t he plat e posit ion in t he inboardout board direct ion. Adjust t he plat e posit ion by gent ly pressing inboard unt il a st op is felt . a a b ) There should be a consist ent dist ance t o door sill line along t he lengt h of t he plat e. b 7.5) Inst all LH Kick Plat e a ) While light ly pressing dow n on kick plat e, peel INBOARD t ape liner com plet ely aw ay. 1 Nissan North Am erica 0 510 20 24 Page 25 of 50 7.6) Inst all LH Kick Plat e a ) While light ly pressing dow n on kick plat e, peel OUTBOARD t ape liner com plet ely aw ay. b ) Press light ly on kick plat e out board edge. 2 7.7) Inst all LH Kick Plat e a ) Apply 15 lbs of pressure along t he part to attach tape to body. CAUTION Use caut ion w hen applying pressure as t he surface m ay dent . 7.8) Inst all LH Kick Plat e a ) Pull up on rear LH door sill w eat herst rip along bot t om as show n. Nissan North Am erica 0 510 20 24 Page 26 of 50 7.9) Clean LH door at t achm ent area a ) Wipe door flange area clean of any dirt . b ) Wipe using alcohol/ w at er solut ion on a soft non-lint ing clot h. c ) Let dry for 30 seconds. 7.10 ) Rout e LH Kick Plat e Harness a ) Rout e IKP harness under door w eat herst rip, across t he m et al sill flange. 7.11) Rout e LH Kick Plat e Harness b a ) Form IKP harness w ire over t he door sill flange. b ) Apply Foam Tape, Black (G) over w ire harness. Tape should not be low er t han halfw ay dow n t he flange. Fo am Tap e, Black (G) c ) Firm ly press w eat herst rip back dow n along lengt h of door. Nissan North Am erica 0 510 20 24 Page 27 of 50 7.12) Rout e LH Kick Plat e Harness a ) Secure t he IKP harness t o t he vehicle harness w it h 1Cable Tie (E) in t he locat ion show n. Cab le Tie (E) CAUTION DO NOT secure t he w irin g t o w at er drain or w asher fluid t ubing. Fo a m b Harness 7.13) Rout e LH Kick Plat e Harness a ) Wrap Foam Tape, Gray (H) around harness in 3 places as show n. b ) Wrap foam around harness in manner as shown in the cross section view. Fo am Tap e (H) Front of Vehicle 7.14) Rout e LH Kick Plat e Harness a ) Rout e t he IKP harness along t he c bot t om inboard edge of t he B-Pillar t rim . b ) Using fingers, push harness under full lengt h of t rim . c ) Pull harness t ight at forw ard end t o help pull harness under B-Pillar t rim . Nissan North Am erica 0 510 20 24 Page 28 of 50 7.15) Rout e LH Kick Plat e Harness a ) At forw ard end of harness, rout e IKP harness along inboard side of vehicle harness as show n. b ) Secure t he IKP harness t o t he vehicle harness w it h 1Cable Tie (E) as show n. Cab le Tie (E) Front of Vehicle 7.16) Inst all RH Kick Plat e a ) Repeat st eps 7.1t hrough 7.15 t o inst all Kick Plat e, Rear RH (D) on RH side. Nissan North Am erica 0 510 20 24 Page 29 of 50 Front of Vehicle 8.1) Clean LH door at t achm ent area a ) Wipe door sill area clean of any dirt . b ) Wipe using alcohol/ w at er solut ion on a soft non-lint ing clot h. c ) Let dry for 30 seconds. 32 8.2) Inst all LH Kick Plat e a ) Part ially peel aw ay enough of t he 3 adhesive liners t o fold dow n a "flag" 1 t hat w ill ext end beyond t he out er edge of Illum inat ed Kick Plat e (A) as show n. 32 8.3) Inst all LH Kick Plat e a ) Posit ion Illum inat ed Kick Plat e, Front LH (A) on door sill area, lining up rearw ard edge of (A) w it h forw ard edge of m asking t ape. 1 Nissan North Am erica 0 510 20 24 Page 30 of 50 a a b 8.4) Inst all LH Kick Plat e a ) Adjust t he plat e posit ion in t he inboardout board direct ion. Adjust t he plat e posit ion by gent ly pressing inboard unt il a st op is felt . b ) There should be a consist ent dist ance t o door sill line along t he lengt h of t he plat e. 8.5) Inst all LH Kick Plat e a ) While light ly pressing dow n on kick plat e, peel 2 INBOARD t ape liners com plet ely aw ay. 2 1 Nissan North Am erica 0 510 20 24 Page 31 of 50 8.6) Inst all LH Kick Plat e a ) While light ly pressing dow n on kick plat e, peel t he rem aining OUTBOARD t ape liner com plet ely aw ay. b ) Press light ly on kick plat e out board edge. 3 8.7) Inst all LH Kick Plat e a ) Apply 15 lbs of pressure along t he part to attach tape to body. CAUTION Use caut ion w hen applying pressure as t he surface m ay dent . 8.8) Inst all LH Kick Plat e a ) Pull up on front LH door sill w eat herst rip along bot t om edge as show n. Nissan North Am erica 0 510 20 24 Page 32 of 50 8.9) Clean LH door at t achm ent area a ) Wipe door flange area clean of any dirt . b ) Wipe using alcohol/ w at er solut ion on a soft non-lint ing clot h. c ) Let dry for 30 seconds. 8.10 ) Rout e LH Kick Plat e Harness a ) Rout e IKP harness under door w eat herst rip, across t he m et al sill flange. 8.11) Rout e LH Kick Plat e Harness b a ) Form IKP harness w ire over t he door sill flange. b ) Apply Foam Tape, Black (G) over w ire harness. Tape should not be low er t han halfw ay dow n t he flange. Fo am Tap e, Black (G) c ) Firm ly press w eat herst rip back dow n along lengt h of door. Nissan North Am erica 0 510 20 24 Page 33 of 50 8.12) Rout e LH Kick Plat e Harness a ) Rout e IKP harness under w hit e vehicle harness t ray t o inboard side. 8.13) Route LH IKP Harness a ) Connect Front IKP harness to Rear IKP harness. b ) Wrap with Foam Tape, Gray (H). Foam Tape, Gray (H) 8.14) Rout e LH Kick Plat e Harness a ) Rout e IKP harness along inboard side of vehicle harness and secure w it h 3 Cable Ties (E) as show n. Cab le Tie (E) CAUTION DO NOT secure t he w irin g t o w at er drain or w asher fluid t ubing. Nissan North Am erica 0 510 20 24 Page 34 of 50 8.15) Connect ASC (AAA) t o IKP a ) Wrap LH side IKP harness fuse w it h Fo am Tape, Gray (H). Fo am Tap e, Gray (H) 8.16) Connect ASC (AAA) t o IKP a ) Plug LH ASC int o LH D-Opt connect or. D-Opt Con nect o r 8.17) Inst all RH Kick Plat e a ) Repeat st eps 8.1t hrough 8.16 t o inst all Kick Plat e, Front RH (D) on RH side. Nissan North Am erica 0 510 20 24 Page 35 of 50 9.1) Secure w ire harness - LH a ) Secure t o IKP harness t o vehicle harness w it h 3 Cable Ties (E) as show n. Cab le Tie (E) CAUTION DO NOT secure t he w irin g t o w at er drain or w asher fluid t ubing. 9.2) Secure w ire harness - RH a ) Repeat st ep 9.1for front RH side. 9.3) Secure w ire harness a ) Cut excess lengt h from all cable t ies on front and rear kick plat es. Nissan North Am erica 0 510 20 24 Page 36 of 50 9.4) Elect rical funct ion check a ) Re-connect negat ive bat t ery cable ARIYA 9.5) Elect rical funct ion check a ) Open all doors. b ) Confirm all Illum inat ed Kick Plat es t urn ON . Nissan North Am erica 9.6) Elect rical funct ion check a ) If NG, check fusing, harness rout ing, connect ions, and IKP t o ident ify root c a u se. CAUTION Wh en d iag n o sin g elect rical syst em problem s, first disconnect t he accesso ry co n n ect o r(s) an d n o t e effect o n veh icle syst em . Con t in u e t he invest igat ion w it h t he accessory co n n ect o r(s) d isco n n ect ed . Reco n n ect w h en t h e in vest ig at io n is com plet e. 0 510 20 24 Page 37 of 50 9.7) Replace t rim a ) Re-inst all int erior t rim t hat w as rem oved in Sect ions 3 t hrough 5. CAUTION Take care not t o scrat ch or dam age any com ponent during t he rem oval or re-inst allat ion process. Trim pieces found t o have w it ness m arks or broken clips should be replaced w it h new part s. Nissan North Am erica 0 510 20 24 Page 38 of 50 9.8) Com plet e checklist : Make sure negat ive bat t ery t erm inal is fully seat ed on post Tight en bat t ery t erm inal nut t o 6.3 - 9.2 N·m [55.7 - 81.4 in·lbs] Verify re-inst alled t rim part s for proper fit (no gap, w aviness, et c.), part icularly t he door sill w eat her st rip. Verify all w indow s and sunroof (if equipped), one t ouch operat ion and perform t he reset procedure if necessary. Refer t o t he vehicle Service Manual for m ore det ails. Re-program radio preset s and ot her vehicle set t ings t o t he recorded set t ings if necessary. Rem ove all t ools, t em plat es, and ot her debris from int erior of vehicle. Verify vehicle headliner, seat , st eering w heel, cent er console, carpet , et c. are not soiled. Verify int erior and ext erior are not dam aged. Verify glove box lam p operat ion. Nissan North Am erica 0 510 20 24 Page 39 of 50 APPENDIX A - POSI- TAP PROCEDURE A.1) Inst alling Posi-Tap on Accessory Service Connect or (AAA) a ) Ident ify and confirm ASC w ire t o be t apped. Check color as w ell as connect or locat ion. b ) Separat e w ire from rest of bundle. A < 10 mm B A.2) Inst alling Posi-Tap on ASC (AAA) a ) Rem ove pierce cap (A) gray side from t ap body b ) Slide cap around single w ire t o be t apped c ) Posit ion cap < 10 m m aw ay from heat shrink end of connector d ) Turn t ap (B) clockw ise unt il finger "t ight ". Then secure t o cap (A) w it h anot her ¼ t urn. CAUTION Do n o t o vert ig h t en Po si- Tap , it m ay dam age w ire A.3) Inst alling Posi-Tap on ASC (AAA) a ) Inspect Posi-Tap t o ensure correct inst allat ion. b ) Wire jacket should be crushed enough t o m aint ain pressure. c ) Confirm t ap cap gap is st raight and evenly spaced around perim et er. Nissan North Am erica 0 510 20 24 Page 40 of 50 APPENDIX A - POSI- TAP PROCEDURE B C A.4) Inst alling Accessory w ire int o Posi-Tap a ) Rem ove t ap bot t om (C) red side from t ap body (B). b ) Rem ove t he pre cut insulat ion from correct Accessory w ire. c ) Insert w ire t hrough t ap bot t om (C) opening. d ) Fan out individual w ire st rands as show n. e ) Insert w ire int o t ap body unt il it bot t om s out . f ) Turn t ap bot t om (C) clockw ise unt il finger "t ight ". Then secure t o t ap body (B) w it h another ¼ turn. A.5) Inst alling accessory w ire int o Posi-Tap a ) Confirm t ap bot t om gap is st raight and evenly spaced around perim et er b ) Gent ly pull on w ire t o confirm secure connect ion. 15 mm A B A.6) Accessory w ire st rain relief a ) Measure 15 m m from point (A). b ) Gent ly form a loop at point (B) and bend back up t ow ards Posi-Tap (bend radius 10 m m ). c) Gent ly form a loop at point (C) and bend back over t op of Posi-Tap and dow n opposit e side (bend radius 10 m m ). C Nissan North Am erica 0 510 20 24 Page 41 of 50 APPENDIX A - POSI- TAP PROCEDURE A.7) Accessory w ire st rain relief a ) Secure accessory w ire st rain relief t o t ap body w it h elect rical t ape ( 2 revolut ions). A.8) Accessory w ire st rain relief a ) Once accessory w ire st rain relief is t aped t o t ap body, it should look as show n. A.9) Inst alling Posi-Tap on ASC (AAA) a ) Repeat st eps A.1- A.8 for all ot her w ires requiring a Posi-Tap . Nissan North Am erica 0 510 20 24 Page 42 of 50 APPENDIX A - POSI- TAP PROCEDURE A.10 ) Securing m ult iple Posi-Taps t oget her a ) St ack Posi-Taps in slight ly st aggered fashion as show n. b ) Secure t apped circuit s t oget her w it h elect rical t ape ( 2 revolut ions). Nissan North Am erica 0 510 20 24 Page 43 of 50 APPENDIX A - POSI- TAP PROCEDURE A.11) Securing m ult iple Posi-Taps t oget her a ) Once t apped circuit s are secured t oget her w it h elect rical t ape t hey should look as show n. Nissan North Am erica 0 510 20 24 Page 44 of 50 APPENDIX A - POSI- TAP PROCEDURE A.12) Securing m ult iple Posi-Taps t oget her a ) Secure Posi-Taps t oget her w it h elect rical t ape ( 4 revolut ions). Nissan North Am erica 0 510 20 24 Page 45 of 50 APPENDIX A - POSI- TAP PROCEDURE A.13) Securing m ult iple Posi-Taps t oget her a ) Once Posi-Taps are secured t oget her w it h elect rical t ape t hey should look as show n. Nissan North Am erica 0 510 20 24 Page 46 of 50 APPENDIX A - POSI- TAP PROCEDURE A.14) Securing m ult iple Posi-Taps t oget her a ) To prevent any possible noise or rat t le issues, use t w o pieces of Foam Tape, Gray (H) t o w rap pre-t aped Posi-Taps . Fo am Tap e (H) Nissan North Am erica 0 510 20 24 Page 47 of 50 APPENDIX A - POSI- TAP PROCEDURE A.15) Securing m ult iple Posi-Taps t oget her a ) Once w rapped w it h Foam Tape, t aped Posi-Tap bundle should look as show n. Nissan North Am erica 0 510 20 24 Page 48 of 50 APPENDIX B - MECHANIZATION DRAWING B.1) Figure below applies t o t he Illum inat ed Kick Plat es connect ed t o t he LH and RH ASC IGN 1 - - - - - - - w hit-e- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - BAT 2 - - - - - - - red- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - TAIL_LAMP 3 - - - - - - - purp-le- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ROOM_LAMP 4 - - - - - - - yello-w- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - BAT_SAVER 5 - - - - - - - p in k- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - FR_DOOR_SW_RH 6 - - - - - - - gree-n- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - FR_DOOR_SW_LH 7 - - - - - - - lt _gre-e-n- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - THRU_SIGNAL 8 - - - - - - - gray- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SECURITY_INDICATOR 9 - - - - - - - blue- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - HORN 10 - - - - - - - lt _blu-e- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ACC 11 - - - - - - - orang- -e- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - GND 12 - - - - - - - blac-k- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Accesso ry Service Co n n ect o r (AAA) RED BLK Illuminated Kick Plate, Front Nissan North Am erica 0 510 20 24 Page 49 of 50 APPENDIX B - MECHANIZATION DRAWING B.1) Figure below applies t o t he Illum inat ed Kick Plat es connect ed t o t he LH and RH ASC CONNECTOR P/ N T99F6 4RA0 A CONNECTOR NAME ACCESSORY SERVICE CONNECTOR CONNECTOR COLOR WHITE POSI- TAP LEGEND GRAY - CIRCUIT TAP (PIERCE) SIDE U N RED - ACCESSORY I (INSERT) SIDE T Not e: Pin locat ion is referenced looking int o harness side of connect or w it h lock t ab orient ed as show n. Nissan North Am erica 0 510 20 24 Page 50 of 50Microsoft Excel for Microsoft 365