Candauto F133 Car MP5 Player Operation Manual

Content

• Tips and Warnings
• Safety Notice
• Disassembly and Installation Steps
• REAR INTERFACE DESCRIPTION
• POWER HARNESS DESCRIPTION
• Rear View Camera Wiring
• Icon Introduction
• Phone Link
• Steering Wheel Control
• Parameters
• USB DVR function (optional)

Tips and Warnings

In order to emphasize the important information of the user manual, special attention should be paid when seeing the label ⚠️, which indicates some important warnings and reminders.

Safety Notice

Read all instructions before installation. It is recommended that the machine be installed by a car audio professional.

• This machine is suitable for the vehicle 12V power supply system (the ground wire must be grounded). Please do not install the machine in a 24V vehicle, otherwise it will damage the machine.
• Do not repair the power fuse without professional guidance. Improper use of the fuse can cause damage to the machine and cause a fire.
• To avoid violating traffic rules, drivers cannot watch videos while driving and operating machines to avoid unnecessary accidents.
• For the sake of safety and to ensure the normal use of the product, please invite professionals to install, disassemble or repair the machine to avoid machine damage and accidents.
• Please do not place this product in a humid environment and water in case causing fire due to electric shock or other unnecessary damage.

Note: To Prevent Burning The Machine, Do Not Turn On The Power Until The Power Cord Is Properly Connected!

Test

A quick simple test before the installation is to confirm that the device is working normally and as expected in case there is a wrong step in the subsequent installation, which will cause it to fail to work. If you perform a successful test but the unit did not work after installing it, please recheck the installation steps.

Test car stereo:

1. The red and yellow wires of the car stereo combine together firstly and then connected to the positive pole of the 12V battery.
2. The black wire is connected to the negative pole of the battery.
3. Two seconds later, check the car stereo. If the screen is lighting up, it means the car stereo is properly functioning.

Disassembly and Installation Steps

1. Screw fixed installation

2. Card position fixed installation

3. Special frame fixed installation

REAR INTERFACE DESCRIPTION

(Note: The picture is for reference only, please refer to the actual product)

Hardware 1

• Power Cable
• USB Cable
• Radio Antenna
• S.W Output
• Video Output
• Video Input
• Camera Input

Hardware 2

• Video Output
• Audio Output 1
• Radio Antenna
• Audio Output 2
• S.W Output
• Camera Input
• Power Cable
• USB DVR
• Video Input

Hardware 3

• Video Output
• Audio Output
• Radio Antenna
• Audio Output 2
• Canbus
• Camera Input
• Power Cable
• USB DVR
• Video Input
• S.W Output

POWER HARNESS DESCRIPTION

(Note: The picture is for reference only, please refer to the actual product)

Power Harness 1

Connections: Auto Antenna, Steering wheel, Rear Camera, Headlight detection line, ACC, Battery 12V

Power Harness 2

Wiring Description:

• Orange: Illuminate Backlight
• Orange/Black: Steering Wheel Control(2)
• Orange/Black: Steering Wheel Control(1)
• Pink: Reversing Camera Wires
• Brown: Brake Detect
• Red: +12V Ignition Switch
• Blue: Auto Antenna
• Green/Black: Rear Left Speaker-
• Green: Rear Left Speaker+
• Purple/Black: Rear Right Speaker-
• Purple: Rear Right Speaker+
• White/Black: Front Left Speaker-
• White: Front Left Speaker+
• Gray/Black: Front Right Speaker-
• Gray: Front Right Speaker+
• Black: Ground Wire(B-)
• Yellow: +12V Constant Power Supply(B+)

Connections: Headlight detection line, Steering Wheel, Reversing Camera, ACC, Auto Antenna, 12V (B+)

Power Harness 3

Speaker Connections:

• Purple: Rear Right Speaker +
• Purple/Black: Rear Right Speaker -
• Gray: Front Right Speaker +
• Gray/Black: Front Right Speaker -
• White: Front Left Speaker +
• White/Black: Front Left Speaker -
• Green: Rear Left Speaker +
• Green/Black: Rear Left Speaker -

Other Connections:

• Pink: Parking Sensor Control Line
• Rear View Camera
• Brown: Brake Line
• Ground Wire(B-)
• Orange/Black: Steering Wheel Control
• Steering Wheel
• Yellow: +12V Constant Power Supply
• +12V(B+)
• Black: Ground Wire(B-)
• Ground Wire
• Orange: Illuminate Backlight
• Headlight Detection Line
• Red: +12V Ignition Switch
• ACC

Rear View Camera Wiring

When using the rear view reversing function, the system will automatically disconnect the link with the mobile phone, such as calls and music in Bluetooth mode, mobile phone mirroring links, etc., which are all normal.

Note: When Installing, Whether You Use a Reversing Camera Or Not, Please Connect The Reversing Cable. Otherwise, Your Wifi And Bluetooth Signals Will Be Affected !

Components:

1. Monitor (Not Included in the Package)
2. Camera Power Source
3. Camera (Optional)

Wiring Diagram:

Connect the reversing trigger line to the reversing line in the power harness (e.g., Back A6). Connect the red wire to the positive pole of the Reverse light Cable. Connect the yellow wire to Back to GND. The camera power cable connects to the reversing light cable.

Monitor Details:

• 1. NTSC FORMAT
• 2. PAL/NTSC Auto Switch Light

Icon Introduction

1. Machine - Host

2. Remote Control Description (Optional)

• 1: MUTE
• 2: MODE
• 3: POWER
• 4: ENT
• 5: PREVIOUS/NEXT
• 6: VOLUME-
• 7: HANG UP
• 8: NUMBER
• 9: MENU
• 10: VOLUME+
• 11: ANSWER

3. Show UI

(Note: The picture is for reference only, please refer to the actual product)

The UI displays various options including Vehicle settings, Basic Setup, Radio, EQ Setup, Display settings, Wallpaper, and ScreenSave. Users can select radio areas like China, America1, America2, Japanese, Russian, Middle East, Europe, and Brazil. The EQ settings allow adjustment for frequencies from 30Hz to 16KHz with options for Jazz, Classic, Rock, Pop, Soft, and User presets.

Phone Link

The Phone Link feature supports both iPhone and Android devices, offering Wired/Wireless iOS CarPlay, Wired iOS mirror Link, Wired/Wireless Android Auto, and Wired Android mirror Link. Users can choose the connection method according to their requirements.

Steering Wheel Control

The steering wheel control function allows users to long-press the steering wheel button and then short-press the screen button to access various functions like Pre, Next, Power, Vol-, Vol+, Mute, Dial, Reject, and Mode. The system also supports custom learning for steering wheel controls.

Steering wheel control learning method:

Connect the KEY and KEY2 on the car player's power cable plug to the original car's steering wheel control wire. After touching the button icon on the screen, quickly find the corresponding function button on the steering wheel of the original car, then press the button until the machine screen prompts that the installation is successful, then release it! This indicates that the learning is successful, and you can learn the next button.

Parameters

USB DVR function (optional)

The USB DVR function allows for taking pictures, recording video, locking footage, and replaying recordings. Users can access a setting interface to configure options. The icon REC flashing indicates video recording is in progress. A different icon indicates sound recording (optional voice and no voice). Another icon signifies recycling of video from a few minutes.