invt TM700 Series Programmable Controller
Khoom Specifications
- Khoom npe: TM700 series programmable maub los
- Tsim los ntawm: INVT
- Txhawb nqa: EtherCAT npav, Ethernet npav, RS485
- Nta: On-board high-speed I/O interfaces, mus txog 16 lub zos expansion modules
- Kev nthuav dav: CANopen / 4G kev ua haujlwm tuaj yeem nthuav dav los ntawm daim npav txuas ntxiv
Cov lus qhia siv khoom
Kev teeb tsa
Phau ntawv mas qhia txog kev teeb tsa thiab kev xaim ntawm cov khoom. Nws suav nrog cov ntaub ntawv khoom siv, kev teeb tsa txhua yam, thiab kev teeb tsa hluav taws xob.
Pre-Installation Cov kauj ruam
- Nyeem los ntawm phau ntawv ua tib zoo ua ntej txhim kho lub programmable maub los.
- Xyuas kom cov neeg ua haujlwm tuav lub installation muaj kev paub txog hluav taws xob.
- Xa mus rau INVT Nruab Nrab thiab Loj PLC Programming Manual thiab INVT Nruab Nrab thiab Loj PLC Software Manual rau cov neeg siv kev txhim kho ib puag ncig thiab tsim qauv.
Cov lus qhia txuas
Ua raws li cov kab hluav taws xob muaj nyob rau hauv phau ntawv qhia kom raug kev sib txuas ntawm programmable controller@
Fais fab rau thiab kuaj
- Tom qab kev teeb tsa thiab xaim, lub zog ntawm lub programmable maub los.
- Ntsuam xyuas kev ua haujlwm ntawm tus maub los los ntawm kev khiav qee qhov kev pab cuam los yog cov khoom siv / tawm.
Cov lus nug nquag nug (FAQ)
- Q: Kuv tuaj yeem tau txais phau ntawv txhais lus tshiab nyob qhov twg?
A: Koj tuaj yeem rub tawm qhov tseeb phau ntawv qhia los ntawm official webqhov chaw www.invt.com ua. Xwb, koj tuaj yeem luam theej duab QR code ntawm cov khoom vaj khoom tsev kom nkag mus rau phau ntawv. - Q: Yuav ua li cas tiv thaiv kev nyab xeeb thaum siv TM700 series programmable controller?
A: Ua ntej tsiv, txhim kho, xaim, xaim, thiab khiav lub programmable maub los, ua tib zoo nyeem thiab ua raws li tag nrho cov kev tiv thaiv kev nyab xeeb uas tau teev tseg hauv phau ntawv los tiv thaiv cov khoom puas lossis raug mob lub cev.
Ua ntej
Tshajview
- Ua tsaug rau koj xaiv TM700 series programmable maub los (programmable maub los luv luv).
- TM700 series programmable controllers yog ib tiam tshiab ntawm cov khoom nruab nrab PLC ntawm nws tus kheej tsim los ntawm INVT, uas txhawb nqa EtherCAT tsheb npav, Ethernet npav, RS485, on-board high-speed I/O interfaces, thiab mus txog 16 lub zos expansion modules. Tsis tas li ntawd, kev ua haujlwm xws li CANopen / 4G tuaj yeem nthuav dav los ntawm daim npav txuas ntxiv.
- Phau ntawv qhia tshwj xeeb tshaj yog qhia txog kev teeb tsa thiab kev xaim ntawm cov khoom, suav nrog cov ntaub ntawv khoom, kev teeb tsa kev siv tshuab, thiab kev teeb tsa hluav taws xob.
- Nyeem los ntawm phau ntawv no ua tib zoo ua ntej txhim kho lub programmable maub los. Yog xav paub meej txog cov neeg siv kev tsim kho ib puag ncig thiab cov txheej txheem tsim qauv siv, saib INVT Nruab Nrab thiab Loj PLC Programming Manual thiab INVT Nruab Nrab thiab Loj PLC Software Manual.
- Phau ntawv yuav hloov pauv yam tsis tau ceeb toom ua ntej. Thov mus saib www.invt.com ua mus download tau qhov tseeb phau ntawv version.
Cov neeg mloog
Cov neeg ua haujlwm nrog kev paub txog hluav taws xob (xws li cov kws tsim hluav taws xob tsim nyog lossis cov neeg ua haujlwm uas muaj kev paub zoo sib xws).
Hais txog cov ntaub ntawv tau txais
Phau ntawv no tsis xa nrog rau cov khoom. Yuav kom tau txais ib qho hluav taws xob version ntawm PDF file, koj tuaj yeem: Mus saib www.invt.com ua, xaiv Kev Txhawb> Download, sau lo lus tseem ceeb, thiab nyem Nrhiav. Luam theej duab QR code ntawm cov khoom vaj khoom tsev → Sau lo lus tseem ceeb thiab rub tawm phau ntawv.
Hloov keeb kwm
Phau ntawv yuav hloov pauv tsis tu ncua yam tsis muaj kev ceeb toom ua ntej vim cov khoom hloov kho tshiab lossis lwm yam laj thawj.
| Tsis muaj. | Hloov cov lus piav qhia | Version | Hnub tso tawm |
| 1 | Thawj tso. | v 1.0 | Lub Yim Hli 2024 |
Kev ceev faj txog kev nyab xeeb
Kev tshaj tawm kev nyab xeeb
Ua tib zoo nyeem phau ntawv no thiab ua raws li tag nrho cov kev tiv thaiv kev nyab xeeb ua ntej tsiv, txhim kho, txuas, commissioning thiab khiav lub programmable controller. Txwv tsis pub, cov cuab yeej puas lossis raug mob lossis tuag yuav tshwm sim.
Peb yuav tsis lav los yog lub luag hauj lwm rau tej yam khoom puas tsuaj los yog lub cev raug mob los yog tuag vim tsis ua raws li kev tiv thaiv kev nyab xeeb.
Kev nyab xeeb qib txhais
Txhawm rau kom muaj kev nyab xeeb ntawm tus kheej thiab zam kev puas tsuaj ntawm vaj tse, koj yuav tsum ua tib zoo mloog cov cim ceeb toom thiab cov lus qhia hauv phau ntawv.
| Ceeb toom cim | Lub npe | Kev piav qhia | ||||
 |
Kev phom sij | Tus kheej raug mob hnyav lossis tuag taus
tsis ua raws li cov cai. |
ua tau | tshwm sim | if | ntsig txog |
 |
Ceeb toom | Kev raug mob ntawm tus kheej lossis khoom siv puas tsuaj
tsis ua raws li cov cai. |
ua tau | tshwm sim | if | ntsig txog |
Cov neeg ua haujlwm xav tau
Cov kws tshaj lij thiab tsim nyog: Cov neeg ua haujlwm cov cuab yeej yuav tsum tau txais kev cob qhia kev siv hluav taws xob thiab kev nyab xeeb, thiab yuav tsum paub txog txhua kauj ruam thiab cov kev xav tau ntawm cov cuab yeej txhim kho, commissioning, khiav thiab tswj thiab muaj peev xwm tiv thaiv kev kub ntxhov raws li kev paub dhau los.
Cov txheej txheem kev nyab xeeb
| Cov ntsiab cai dav dav | |
| |
|
| Kev xa khoom thiab kev teeb tsa | |
| |
|
| Kev xaim | |
| |
|
| Kev ua haujlwm thiab ua haujlwm | |
| |
|
| Kev tu thiab hloov cov khoom siv | |
| |
|
| Kev pov tseg | |
| |
|
 |
|
Khoom dhau lawmview
Khoom npe thiab qauv 
| Qauv | Specifications |
| TIAB SA 750 | Tiav maub los; PLC nruab nrab; EtherCAT; 4 axes; 2 × Ethernet; 2 × RS485; 8 inputs thiab 8 outputs. |
| TIAB SA 751 | Tiav maub los; PLC nruab nrab; EtherCAT; 8 axes; 2 × Ethernet; 2 × RS485; 8 inputs thiab 8 outputs. |
| TIAB SA 752 | Tiav maub los; PLC nruab nrab; EtherCAT; 16 axes; 2 × Ethernet; 2 × RS485; 8 inputs thiab 8 outputs. |
| TIAB SA 753 | Tiav maub los; PLC nruab nrab; EtherCAT; 32 axes; 2 × Ethernet; 2 × RS485; 8 inputs thiab 8 outputs. |
Interface piav qhia 
| Tsis muaj. | Hom chaw nres nkoj | Interface
kos npe |
Txhais | Kev piav qhia |
| 1 | Qhov taw qhia I/O | - | I/O lub xeev zaub | On: Lub tswv yim / tso zis yog siv tau. Tawm: Lub tswv yim / tso zis tsis raug. |
| Tsis muaj. | Hom chaw nres nkoj | Interface
kos npe |
Txhais | Kev piav qhia |
| 2 | Pib / nres DIP hloov | Khiav | Tus neeg siv qhov program khiav lub xeev | Tig rau RUN: Tus neeg siv qhov program khiav. Tig rau STOP: Tus neeg siv qhov program nres. |
| TSIS TAU | ||||
| 3 | Qhov taw qhia txog kev ua haujlwm | PWR | Fais fab xeev zaub | On: Lub hwj chim mov yog qhov qub. Tawm: Lub hwj chim mov yog txawv txav. |
| Khiav | Khiav lub xeev zaub | Ntawm: Cov neeg siv qhov program tab tom khiav. Tawm: Cov neeg siv qhov program nres. |
||
|
ERR |
Khiav yuam kev xeev zaub | On: Ib qho yuam kev loj tshwm sim. Flash: Ib qho yuam kev. Tawm: Tsis muaj qhov yuam kev tshwm sim. |
||
| 4 | Daim npav nthuav dav
qhov |
- | Expansion daim npav qhov, siv rau kev ua haujlwm txuas ntxiv. | Saib seem Daim Ntawv Ntxiv Ntxiv Ib Daim Npav Ntxiv Ntxiv. |
| 5 | RS485 interface |
R1 |
Channel 1 Terminal resistor |
Ua-nyob rau hauv 120Ω resistor; luv-circuit qhia txog kev sib txuas ntawm 120Ω davhlau ya nyob twg resistor. |
| A1 | Channel 1 485 kev sib txuas lus teeb liab + | - | ||
| B1 | Tshawb cov txiaj ntsig rau «youtube» - Nplooj 1 - PYMEX | - | ||
| R2 | Channel 2 Terminal resistor | Ua-nyob rau hauv 120Ω resistor; luv-circuit qhia txog kev sib txuas ntawm 120Ω davhlau ya nyob twg resistor. | ||
| A2 | Channel 2 485 kev sib txuas lus teeb liab + | - | ||
| B2 | Tshawb cov txiaj ntsig rau «youtube» - Nplooj 2 - PYMEX | - | ||
| GND | RS485 kev sib txuas lus teeb liab siv hauv av | - | ||
| PE | PE | - | ||
| 6 | Lub zog interface | 24v XNUMX | DC 24V fais fab mov + | - |
| 0V | DC 24V fais fab mov - | - | ||
| PE | PE | - | ||
| 7 | Ethernet chaw nres nkoj | Ethernet 2 | Ethernet kev sib txuas lus interface | Default IP: 192.168.2.10 Ntsuab qhov taw qhia ntawm: Nws qhia tias qhov txuas tau tsim tiav. Green qhia tawm: Nws qhia tias qhov txuas tsis tau tsim. Yellow indicator flashing: Nws qhia tias kev sib txuas lus tau ua tiav. Yellow indicator off: Nws qhia tias tsis muaj kev sib txuas lus. |
| Tsis muaj. | Hom chaw nres nkoj | Interface kos npe | Txhais | Kev piav qhia |
| 8 | Ethernet chaw nres nkoj | Ethernet 1 | Ethernet kev sib txuas lus interface | Default IP: 192.168.1.10 Green qhia rau: Nws qhia tau hais tias qhov txuas tau tsim tiav. Green qhia tawm: Nws qhia tias qhov txuas tsis tau tsim. Yellow indicator flashing: Nws qhia tias kev sib txuas lus tau ua tiav. Yellow indicator off: Nws qhia tias tsis muaj kev sib txuas lus. |
| 9 | EtherCAT interface | EtherCAT | EtherCAT kev sib txuas lus interface | Green indicator on: Nws qhia tias qhov txuas tau tsim tiav. Green qhia tawm: Nws qhia tias qhov txuas tsis tau tsim. Yellow indicator flashing: Nws qhia tias kev sib txuas lus tau ua tiav. Yellow indicator off: Nws qhia tias tsis muaj kev sib txuas lus. |
| 10 | I/O davhlau ya nyob twg | - | 8 inputs thiab 8 outputs | Yog xav paub ntxiv, saib tshooj 4.2 I/O davhlau ya nyob twg thaiv. |
| 11 | MicroSD daim npav interface | - | - | Siv rau firmware programming, file nyeem ntawv thiab sau ntawv. |
| 12 | Hom-C interface |  |
Kev sib txuas lus ntawm USB thiab PC | Siv rau qhov program download thiab debugging.
Default IP: 192.168.3.10 |
| 13 | khawm roj teeb qhov | TIAB SA 2032 | RTC moos khawm roj teeb qhov | Muaj feem xyuam rau CR2032 khawm roj teeb |
 Nco tseg: Cov khoom tsis yog nruab nrog lub pob roj teeb raws li tus qauv teeb tsa los ntawm lub neej ntawd. Lub pob roj teeb yog tus neeg siv yuav, thiab tus qauv yog CR2032. |
||||
| 14 | Backplane connector | - | Local expansion backplane tsheb npav | Txuas mus rau lub zos expansion modules |
Khoom specifications
General specifications
| Yam khoom | TIAB SA 750 | TIAB SA 751 | TIAB SA 752 | TIAB SA 753 |
| Ethernet interface | 2 channel | 2 channel | 2 channel | 2 channel |
| EtherCAT interface | 1 channel | 1 channel | 1 channel | 1 channel |
| Max. tus naj npawb ntawm axes (bus + mem tes) | 4 axes + 4 axes | 8 axes + 4 axes | 16 axes + 4 axes | 32 axes + 4 axes |
| RS485 ib | 2 raws, txhawb Modbus RTU tus tswv / qhev muaj nuj nqi thiab chaw nres nkoj dawb | |||
| Yam khoom | TIAB SA 750 | TIAB SA 751 | TIAB SA 752 | TIAB SA 753 |
| muaj nuj nqi. | ||||
| EtherNet tsheb npav | Txhawb Modbus TCP, OPC UA, TCP / UDP, program upload thiab rub tawm,
thiab firmware upgrade. |
|||
| Hom-C interface | 1 channel, txhawb kev upload thiab rub tawm, thiab hloov kho firmware. | |||
| DI | 8 inputs Ameslikas, suav nrog 200kHz high-speed inputs | |||
| DO | 8 outputs Ameslikas, suav nrog 200kHz high-speed outputs | |||
| Pulse axis | Txhawb nqa mus txog 4 channels | |||
| Input zog | 24VDC (-15% - + 20%) / 2A, txhawb kev tiv thaiv kev thim rov qab | |||
| Standalone zog noj | <10 W | |||
| Backplane tsheb npav fais fab mov | 5V / 2.5A | |||
| Fais fab-kev tiv thaiv muaj nuj nqi | Txhawb nqa Nco tseg: Lub hwj chim-down tuav tsis tau ua nyob rau hauv 30 vib nas this tom qab fais fab tuag. |
|||
| Real-time moos | Txhawb nqa | |||
| Local expansion modules | Txog li 16, tsis tso cai rau kev sib pauv kub | |||
| Local expansion card | Ib daim npav nthuav dav, txhawb CANopen daim npav, 4G IoT daim npav thiab lwm yam. | |||
| Program lus | IEC61131-3 programming lus (SFC, LD, FBD, ST, IL, CFC) | |||
| Program download | Hom-C interface, Ethernet chaw nres nkoj, MicroSD daim npav, chaw taws teeb rub tawm (4G IoT
expansion card) |
|||
| Program cov ntaub ntawv muaj peev xwm | 20MByte neeg siv kev pab cuam
64MByte kev cai hloov pauv, nrog 1MByte txhawb zog-down tuav |
|||
| Khoom hnyav | Kwv yees li. 0.35 kg ib | |||
| Dimension qhov ntev | Saib seem Daim Ntawv Ntxiv B Dimension drawings. | |||
DI input specifications
| Yam khoom | Kev piav qhia |
| Hom tswv yim | Cov tswv yim digital |
| Tus naj npawb ntawm cov tswv yim nkag | 8 channel |
| Hom tswv yim | Qhov chaw / dab dej hom |
| Cov lus qhia voltage klas | 24VDC (-10% - + 10%) |
| Input tam sim no | X0–X7 raws: Cov tswv yim tam sim no yog 13.5mA thaum ON (tus nqi raug), thiab tsawg dua 1.7mA thaum OFF. |
| Max. input zaus | X0-X7 raws: 200kHz; |
| Input tsis kam | Tus nqi ntawm X0–X7 raws: 1.7kΩ |
| ON voltage | ≥15VDC |
| OFF voltage | ≤ 5VDC |
| Txoj kev cais tawm | Integrated nti capacitive cais |
| Cov txheej txheem davhlau ya nyob twg | 8 channels / lub davhlau ya nyob twg |
| Input nkaus tso saib | Thaum lub tswv yim nyob rau hauv lub xeev tsav tsheb, lub input qhia yog nyob rau (software tswj). |
DO tso zis specifications
| Yam khoom | Kev piav qhia |
| Hom tso zis | Transistor tso zis |
| Tus naj npawb ntawm cov channel tso tawm | 8 channel |
| Tso zis hom | Hom dab dej |
| Tso zis voltage klas | 24VDC (-10% - + 10%) |
| Output load (kuj) | 0.5A / taw tes, 2A / 8 points |
| tso zis load (inductance) | 7.2W / point, 24W / 8 ntsiab lus |
| Hardware teb lub sijhawm | ≤2μs |
| Load tam sim no xav tau | Load tam sim no ≥ 12mA thaum tso zis zaus ntau dua 10kHz |
| Max. tso zis zaus | 200kHz rau cov load tsis kam, 0.5Hz rau cov load kuj, thiab 10Hz rau lub teeb load |
| Cov dej ntws tam sim no ntawm OFF | Hauv qab 30μA (tam sim no tus nqi ntawm ib txwm voltage ntawm 24VDC) |
| Max. seem voltage ON | ≤ 0.5VDC |
| Txoj kev cais tawm | Integrated nti capacitive cais |
| Cov txheej txheem davhlau ya nyob twg | 8 channels / lub davhlau ya nyob twg |
| Short-circuit tiv thaiv muaj nuj nqi | Txhawb nqa |
| Sab nraud inductive load yuav tsum tau | Flyback diode xav tau rau sab nraud inductive load txuas. Saib daim duab 2-1 rau daim duab kab hluav taws xob. |
| Output nkaus tso saib | Thaum cov zis siv tau, qhov ntsuas qhov tso zis yog nyob rau (software tswj). |
| Output derating | Qhov tam sim no ntawm txhua pab pawg ntawm cov davhlau ya nyob twg tsis tuaj yeem tshaj 1A thaum qhov ntsuas kub ntawm 55 ℃. Saib daim duab 2-2 rau qhov nkhaus ntawm derating coefficient. |
RS485 specifications
| Yam khoom | Kev piav qhia |
| Txhawb channel | 2 channel |
| Kho vajtse interface | In-line davhlau ya nyob twg (2 × 6Pin davhlau ya nyob twg) |
| Txoj kev cais tawm | Integrated nti capacitive cais |
| Terminal resistor | Built-in 120Ω davhlau ya nyob twg resistor, xaiv tau los ntawm luv luv R1 thiab R2 ntawm 2 × 6 PIN hauv-kab davhlau ya nyob twg. |
| Tus nab npawb ntawm qhev | Txhua channel txhawb nqa txog 31 tus qhev |
| Kev sib txuas lus baud rate | 9600/19200/38400/57600/115200bps |
| Input tiv thaiv | Txhawb 24V kev tiv thaiv tsis raug |
EtherCAT specifications
| Yam khoom | Kev piav qhia |
| Kev sib txuas lus raws tu qauv | EtherCAT |
| Txhawb kev pabcuam | CoE (PDO/SDO) |
| Synchronization txoj kev | Faib moos rau lub servo;
I/O txais cov tswv yim thiab tso zis synchronization |
| Lub cev txheej | 100BASE-TX |
| Baud tus nqi | 100Mbps (100Base-TX) |
| Duplex hom | Full duplex |
| Topology qauv | Linear topology qauv |
| Xa cov khoom nruab nrab | Qeb-5 lossis siab dua network cables |
| Kev sib kis nrug | Qhov kev ncua deb ntawm ob lub nodes yog tsawg dua 100m. |
| Tus nab npawb ntawm qhev | Txhawb nqa txog 72 tus qhev |
| EtherCAT ncej ntev | 44 bytes–1498 bytes |
| Cov ntaub ntawv txheej txheem | Txog 1486 bytes rau ib qho Ethernet ncej |
Cov lus qhia tshwj xeeb ntawm Ethernet
| Yam khoom | Kev piav qhia |
| Kev sib txuas lus raws tu qauv | Standard Ethernet raws tu qauv |
| Lub cev txheej | 100BASE-TX |
| Baud tus nqi | 100Mbps (100Base-TX) |
| Duplex hom | Full duplex |
| Topology qauv | Linear topology qauv |
| Xa cov khoom nruab nrab | Qeb-5 lossis siab dua network cables |
| Kev sib kis nrug | Qhov kev ncua deb ntawm ob lub nodes yog tsawg dua 100m. |
Mechanical installation
Installation ib puag ncig xav tau
Thaum txhim kho cov khoom no ntawm DIN rail, tag nrho cov kev txiav txim siab yuav tsum tau muab rau kev ua haujlwm, kev tswj xyuas, thiab kev tiv thaiv ib puag ncig ua ntej kev teeb tsa.
| Yam khoom | Specification |
| IP chav kawm | IP20 |
| Cov pa phem theem | Theem 2: Feem ntau tsuas yog tsis muaj kuab paug, tab sis koj yuav tsum xav txog kev hloov pauv hloov pauv los ntawm kev sib xyaw ua ke. |
| Qhov siab | ≤2000m (80kPa) |
| Overcurrent tiv thaiv ntaus ntawv | 3A fuse |
| Max. ua haujlwm kub | 45 ° C nyob rau hauv tag nrho load. Derating yuav tsum tau thaum lub ambient kub yog 55 ° C. Yog xav paub ntxiv, saib daim duab 2-2. |
| Cia kub thiab av noo ntau yam | Kub: -20 ℃ - + 60 ℃; txheeb ze humidity: tsawg dua 90% RH thiab tsis condensation |
| Kev thauj mus los kub thiab av noo ntau | Kub: -40 ℃ - + 70 ℃; txheeb ze humidity: tsawg dua 95% RH thiab tsis condensation |
| Ua haujlwm kub thiab av noo ntau | Kub: -20 ℃ - + 55 ℃; txheeb ze humidity: tsawg dua 95% RH thiab tsis condensation |
Installation thiab disassembly
Kev teeb tsa
Master installation
Teem tus tswv rau DIN rail, thiab nias nws sab hauv kom txog thaum tus tswv thiab DIN rail yog clamped (muaj ib lub suab pom tseeb ntawm clamptom qab lawv tau nruab rau hauv qhov chaw).
Lus Cim: Tus tswv siv DIN rail rau kev teeb tsa.
Installation ntawm tus tswv thiab lub module
Teem lub module nrog cov kev sib txuas rail nrog tus tswv zawv zawg rail, thiab thawb mus rau sab hauv kom txog thaum lub module koom nrog DIN rail (muaj lub suab nrov ntawm kev koom tes thaum nruab rau hauv qhov chaw).
Lus Cim: Tus tswv thiab cov qauv siv DIN rail rau kev teeb tsa.
Expansion card installation
Tshem tawm lub hau ua ntej txhim kho daim npav nthuav dav. Cov kauj ruam installation yog raws li nram no.
- Kauj Ruam 1 Siv ib lub cuab yeej los maj mam rub lub npog snap-fits ntawm sab ntawm cov khoom (nyob rau hauv ib theem ntawm txoj hauj lwm 1 thiab 2), thiab tshem tawm lub hau horizontally mus rau sab laug.
Kauj Ruam 2 Xaub daim npav nthuav dav mus rau hauv daim ntawv qhia qhov sib npaug, tom qab ntawd nias cov haujlwm clip nyob rau sab sauv thiab sab qis ntawm daim npav nthuav dav kom txog thaum daim npav nthuav dav yog clamped (muaj ib lub suab pom tseeb ntawm clamptom qab lawv tau nruab rau hauv qhov chaw).
Khawm roj teeb installation
- Kauj ruam 1 Qhib lub pob roj teeb npog.
- Kauj Ruam 2 Nias lub pob roj teeb rau hauv lub pob roj teeb hauv qhov kev coj ua kom raug, thiab kaw lub pob roj teeb npog.
Nco tseg:
- Thov nco ntsoov lub anode thiab cathode ntawm lub roj teeb.
- Thaum lub roj teeb raug teeb tsa thiab cov programming software qhia txog lub tswb ntawm lub roj teeb qis, lub roj teeb yuav tsum tau hloov.
Kev muab cais tawm
Master disassembly
Kauj Ruam 1 Siv cov ntsia hlau ncaj ncaj los yog cov cuab yeej zoo sib xws los rub cov tsheb ciav hlau snap-haum.
Kauj ruam 2 Rub lub module ncaj nraim ua ntej.
Kauj Ruam 3 Nias rau saum lub tsheb ciav hlau snap-haum rau hauv qhov chaw. 
terminal disassembly
- Kauj ruam 1 Nias lub clip nyob rau sab saum toj ntawm lub davhlau ya nyob twg (nce ib feem). Kauj ruam 2 Nias thiab rub tawm lub davhlau ya nyob twg ib txhij.
Khawm roj teeb disassembly
Cov kauj ruam disassembly yog raws li nram no:
- Kauj ruam 1 Qhib lub pob roj teeb npog. (Yog xav paub ntxiv, saib ntu
khawm roj teeb installation). - Kauj Ruam 2 Disassemble I/O terminals (Yog xav paub ntxiv, saib tshooj 3.2.2.2 I/O terminal disassembly).
- Kauj Ruam 3 Siv lub taub hau me me kom maj mam thawb lub pob roj teeb, raws li qhia hauv daim duab hauv qab no.
- Kauj ruam 4 Tshem tawm lub roj teeb thiab kaw lub pob roj teeb npog.
Kev teeb tsa hluav taws xob
Cable specifications
Table 4-1 Cable qhov ntev rau ib kab
| Siv tau kab kab kab | Tubular kab hlau rhuav | |
| Suav standard / hli2 | Neeg Asmeskas standard/AWG |  |
| 0.3 | 22 | |
| 0.5 | 20 | |
| 0.75 | 18 | |
| 1.0 | 18 | |
| 1.5 | 16 | |
| Pin | Teeb liab | Teeb liab kev taw qhia | Cov lus piav qhia |
| 1 | TSI + | Tso zis | Kev xa cov ntaub ntawv + |
| 2 | TSI- | Tso zis | Cov ntaub ntawv kis- |
| 3 | RD+ | Tswv yim | Kev txais cov ntaub ntawv + |
| 4 | ‑ | ‑ | Tsis siv |
| 5 | ‑ | ‑ | Tsis siv |
| 6 | RD- | Tswv yim | Kev txais cov ntaub ntawv- |
| 7 | ‑ | ‑ | Tsis siv |
| 8 | ‑ | ‑ | Tsis siv |
O lub davhlau ya nyob twg thaiv
Terminal txhais
| Schematic daim duab | Sab laug teeb liab | Sab laug terminal | Txoj cai davhlau ya nyob twg | Txoj cai teeb liab |
 |
X0 input | A0 | B0 | Y0 tso zis |
| X1 input | A1 | B1 | Y1 tso zis | |
| X2 input | A2 | B2 | Y2 tso zis | |
| X3 input | A3 | B3 | Y3 tso zis | |
| X4 input | A4 | B4 | Y4 tso zis | |
| X5 input | A5 | B5 | Y5 tso zis |
| Schematic daim duab | Sab laug teeb liab | Sab laug terminal | Txoj cai davhlau ya nyob twg | Txoj cai teeb liab |
| X6 input | A6 | B6 | Y6 tso zis | |
| X7 input | A7 | B7 | Y7 tso zis | |
| SS input common davhlau ya nyob twg | A8 | B8 | COM tso zis ntau lub davhlau ya nyob twg |
Nco tseg:
- Tag nrho ncua ntev ntawm kev kub ceev I / O interface expansion cable yuav tsum nyob rau hauv 3 meters.
- Thaum lub sij hawm xaim hluav taws xob, cov kab hluav taws xob yuav tsum tau sib cais kom tsis txhob bundling nrog fais fab cables (high voltage thiab tam sim no loj) lossis lwm cov cables uas xa cov teeb liab muaj zog cuam tshuam, thiab kev sib txuas yuav tsum tau zam.
Input davhlau ya nyob twg thaiv 
Output davhlau ya nyob twg thaiv 
Nco tseg: Lub flyback diode yog xav tau rau sab nraud inductive load txuas. Daim duab kab hluav taws xob tau qhia raws li hauv qab no.
Kev sib txuas ntawm cov khoom siv hluav taws xob
Terminal txhais 
Terminal txuas 
RS485 kev sib txuas lus 
Nco tseg:
- Shielded twisted khub yog pom zoo rau RS485 tsheb npav, thiab A thiab B txuas nrog cov khub twisted.
- 120 Ω terminal matching resistors yog txuas rau ntawm ob qho kawg ntawm lub npav kom tsis txhob muaj teeb meem cuam tshuam.
- Kev siv hauv av ntawm 485 cov cim ntawm tag nrho cov nodes txuas ua ke.
- Qhov kev ncua deb ntawm txhua kab ntawm kab yuav tsum tsawg dua 3m.
EtherCAT kev sib txuas xov tooj 
Nco tseg:
- Nws yuav tsum tau siv cov hlua khi hlua khi ntawm qeb 5, yas txhaj tshuaj molded thiab hlau plhaub, ua raws li EIA/TIA568A, EN50173, ISO/IEC11801, EIA/TIA bulletin TSB, thiab EIA/TIA SB40-A&TSB36.
- Lub network cable yuav tsum dhau qhov kev ntsuas ntsuas 100%, yam tsis muaj luv luv, qhib Circuit Court, dislocation lossis kev sib cuag tsis zoo.
- Thaum txuas lub network cable, tuav lub taub hau siv lead ua ntawm cable thiab ntxig rau hauv Ethernet interface (RJ45 interface) kom txog thaum nws ua suab nrov.
- Thaum tshem tawm cov teeb tsa network cable, nias tus Tsov tus tw ntawm lub taub hau siv lead ua thiab rub tawm ntawm cov khoom horizontally.
Ethernet thaiv 
Lwm yam piav qhia
Programming cuab yeej
Cov cuab yeej programming: Invtmatic Studio. Yuav ua li cas kom tau txais cov cuab yeej programming: Mus saib www.invt.com ua, xaiv Kev Txhawb> Download, sau lo lus tseem ceeb, thiab nyem Tshawb nrhiav.
Khiav thiab nres cov haujlwm
Tom qab cov kev pabcuam raug sau rau PLC, ua haujlwm khiav thiab nres cov haujlwm raws li hauv qab no.
- Txhawm rau khiav lub kaw lus, teeb tsa DIP hloov mus rau RUN, thiab xyuas kom meej tias RUN qhov taw qhia nyob rau, pom cov xim daj-ntsuab.
- Txhawm rau kom tsis txhob ua haujlwm, teeb tsa DIP hloov mus rau STOP (xws li, koj tuaj yeem nres qhov haujlwm los ntawm keeb kwm yav dhau los ntawm tus tswv tswj hwm).
Kev tu txhua hnub
- Ntxuav lub programmable maub los tsis tu ncua, thiab tiv thaiv cov teeb meem txawv teb chaws poob rau hauv tus maub los.
- Xyuas kom muaj qhov cua zoo thiab cov cua kub dissipation rau tus maub los.
- Tsim cov lus qhia txog kev saib xyuas thiab tsis tu ncua kuaj tus maub los.
- Tsis tu ncua xyuas cov xaim thiab cov terminals kom ntseeg tau tias lawv tau ruaj khov.
MicroSD daim npav firmware upgrade
- Kauj ruam 1 Nruab "Firmware upgrade MicroSD card" rau hauv cov khoom.
- Kauj Ruam 2 Fais fab ntawm cov khoom. Thaum lub PWR, RUN thiab ERR ntsuas nyob rau, nws qhia tau hais tias lub firmware upgrade tiav.
- Kauj Ruam 3 Fais fab tawm ntawm cov khoom, tshem tawm daim npav MicroSD, thiab tom qab ntawd fais fab rau cov khoom dua.
Nco tseg: Kev teeb tsa ntawm MicroSD daim npav yuav tsum tau ua tom qab cov khoom raug kaw.
Appendix A Expansion card accessories
| Tsis muaj. | Qauv | Specification |
| 1 | TM-CAN | Txhawb nqa lub npav CANopen |
| 2 | TM-4 G | Txhawb 4G IoT |
Appendix B Dimension drawings
Koj Trusted IndustryAutomation Solution Provider 
- Shenzhen INVT Electric Co., Ltd.
- Chaw nyob: INVT Guangming Technology Building, Songbai Road, Matian,
- Guangming Cheeb Tsam, Shenzhen, Suav
- INVT fais fab Electronics (Suzhou) Co., Ltd.
- Chaw nyob: No. 1 Kunlun Roob Roob, Science & Technology Town,
- Gaoxin Districts Suzhou, Jiangsu, Suav teb
- Webqhov chaw: www.invt.com ua
Copyright@ INVT. Cov ntaub ntawv ntawm phau ntawv yuav raug hloov pauv yam tsis tau ceeb toom ua ntej.
Cov ntaub ntawv / Cov ntaub ntawv
 |
invt TM700 Series Programmable Controller [ua pdf] Tus neeg siv phau ntawv TM700 Series Programmable Controller, TM700 Series, Programmable Controller, Tus Tswj |
