ESPRESSIF ESP32-S3-WROOM-1 Development Board Bluetooth Module
Cov lus qhia siv khoom
- ESP32-S3-WROOM-1 thiab ESP32-S3-WROOM-1U modules tuaj nrog cov kav hlau txais xov sib txawv. Tus qub muaj PCB kav hlau txais xov, thaum lub tom kawg tuaj nrog lub kav hlau txais xov sab nraud.
- Daim duab tus pin hauv qab no siv tau rau ob qho tib si ESP32-S3-WROOM-1 thiab ESP32-S3-WROOM-1U, nrog rau tom kawg tsis muaj chaw khaws cia.
- Lub module muaj 41 tus pins nrog ntau yam haujlwm. Rau cov lus piav qhia ntxaws txog cov npe tus pin, cov npe ua haujlwm, thiab kev teeb tsa ntawm cov pins peripheral, thov mus rau ESP32-S3 Series Datasheet.
Module Tshajview
Nta
CPU thiab OnChip Memory
- ESP32-S3 series ntawm SoCs embedded, Xtensa® dual-core 32-ntsis LX7 microprocessor, mus txog 240 MHz
- 384 KB ROM
- 512 KB SRAM
- 16 KB SRAM hauv RTC
- Mus txog 8 MB PSRAM
WiFi
- 802.11b/g/n
- Tus nqi qis: 802.11n txog 150 Mbps
- A-MPDU thiab A-MSDU aggregation
- 0.4 μs tiv thaiv lub sijhawm txhawb nqa
- Center zaus ntau ntawm kev khiav hauj lwm channel: 2412 ~ 2462 MHz
Bluetooth
- Bluetooth LE: Bluetooth 5, Bluetooth mesh
- 2 Mbps PHY
- Ntev-ntau hom
- Kev tshaj tawm extensions
- Ntau yam kev tshaj tawm
- Channel xaiv algorithm #2
Peripherals
- GPIO, SPI, LCD interface, Lub koob yees duab interface, UART, I2C, I2S, chaw taws teeb tswj, mem tes txee, LED PWM, USB 1.1 OTG, USB Serial / JTAG maub los, MCPWM, SDIO party, GDMA, TWAI® maub los (tshaj ISO 11898-1), ADC, kov sensor, ntsuas kub, ntsuas sijhawm thiab saib xyuas
Integrated Cheebtsam ntawm Module
- 40 MHz siv lead ua oscillator
- Mus txog 16 MB SPI flash
Kav hlau txais xov Kev xaiv
- On-board PCB kav hlau txais xov (ESP32-S3-WROOM-1)
- Tus kav hlau txais xov sab nraud ntawm qhov txuas (ESP32-S3-WROOM-1U)
Cov xwm txheej ua haujlwm
- Kev khiav hauj lwm voltage / Fais fab mov: 3.0 ~ 3.6V
- Kev khiav hauj lwm kub ambient:
- 65 ° C version: -40 ~ 65 ° C
- 85 ° C version: -40 ~ 85 ° C
- 105 ° C version: -40 ~ 105 ° C
- Dimensions: Saib Table 1
Kev piav qhia
- ESP32-S3-WROOM-1 thiab ESP32-S3-WROOM-1U yog ob lub zog, generic Wi-Fi + Bluetooth LE MCU modules uas tau tsim nyob ib ncig ntawm ESP32-S3 series ntawm SoCs. Nyob rau sab saum toj ntawm cov khoom siv nplua nuj, kev nrawm rau neural network xam thiab teeb liab ua haujlwm ua haujlwm tau muab los ntawm SoC ua rau cov qauv xaiv zoo tshaj plaws rau ntau yam ntawm daim ntawv thov scenarios ntsig txog AI thiab Artificial Intelligence of Things (AIoT), xws li wake lo lus tshawb pom, hais lus commands paub, lub ntsej muag nrhiav kom pom thiab ntse, kev paub hauv tsev. thiab lwm yam ESP32-S3-WROOM-1 los nrog PCB kav hlau txais xov. ESP32-S3-WROOM-1U los nrog tus kav hlau txais xov sab nraud.
- Kev xaiv dav ntawm cov qauv sib txawv yog muaj rau cov neeg siv khoom, raws li qhia hauv Table 1.
- Ntawm cov qauv sib txawv, cov uas embed ESP32-S3R8 ua haujlwm ntawm -40 ~ 65 ° C ambient kub, ESP32-S3-WROOM-1-H4 thiab ESP32-S3-WROOM-1U-H4 ua haujlwm ntawm -40 ~ 105 ° C ambient kub, thiab lwm yam module 40 ° C ambient kub ua haujlwm ntawm -85 ° C
Table 1: Ordering Information
| Ordering Code | Chip Embedded | Flash (MB) | PSRAM (MB) | Qhov Loj (mm) |
| ESP32-S3-WROOM-1-N4 | ESP32-S3 | 4 | 0 |
18 × 25.5 × 3.1 |
| ESP32-S3-WROOM-1-N8 | ESP32-S3 | 8 | 0 | |
| ESP32-S3-WROOM-1-N16 | ESP32-S3 | 16 | 0 | |
| ESP32-S3-WROOM-1-H4 (105 °C) | ESP32-S3 | 4 | 0 | |
| ESP32-S3-WROOM-1-N4R2 | ESP32-S3R2 | 4 | 2 (Quad SPI) | |
| ESP32-S3-WROOM-1-N8R2 | ESP32-S3R2 | 8 | 2 (Quad SPI) | |
| ESP32-S3-WROOM-1-N16R2 | ESP32-S3R2 | 16 | 2 (Quad SPI) | |
| ESP32-S3-WROOM-1-N4R8 (65 °C) | ESP32-S3R8 | 4 | 8 (Octal SPI) | |
| ESP32-S3-WROOM-1-N8R8 (65 °C) | ESP32-S3R8 | 8 | 8 (Octal SPI) | |
| ESP32-S3-WROOM-1-N16R8 (65 °C) | ESP32-S3R8 | 16 | 8 (Octal SPI) | |
| ESP32-S3-WROOM-1U-N4 | ESP32-S3 | 4 | 0 |
18 × 19.2 × 3.2 |
| ESP32-S3-WROOM-1U-N8 | ESP32-S3 | 8 | 0 | |
| ESP32-S3-WROOM-1U-N16 | ESP32-S3 | 16 | 0 | |
| ESP32-S3-WROOM-1U-H4 (105 °C) | ESP32-S3 | 4 | 0 | |
| ESP32-S3-WROOM-1U-N4R2 | ESP32-S3R2 | 4 | 2 (Quad SPI) | |
| ESP32-S3-WROOM-1U-N8R2 | ESP32-S3R2 | 8 | 2 (Quad SPI) | |
| ESP32-S3-WROOM-1U-N16R2 | ESP32-S3R2 | 16 | 2 (Quad SPI) | |
| ESP32-S3-WROOM-1U-N4R8 (65 °C) | ESP32-S3R8 | 4 | 8 (Octal SPI) | |
| ESP32-S3-WROOM-1U-N8R8 (65 °C) | ESP32-S3R8 | 8 | 8 (Octal SPI) | |
| ESP32-S3-WROOM-1U-N16R8 (65 °C) | ESP32-S3R8 | 16 | 8 (Octal SPI) |
- Ntawm qhov tseem ceeb ntawm cov modules yog ESP32-S3 series ntawm SoC *, Xtensa® 32-ntsis LX7 CPU uas ua haujlwm txog li 240 MHz.
- Koj tuaj yeem siv hluav taws xob tawm ntawm CPU thiab siv lub tshuab hluav taws xob qis qis los saib xyuas cov khoom siv txuas mus tas li rau kev hloov pauv lossis hla ntawm qhov pib.
- ESP32-S3 integrates ib tug nplua nuj txheej ntawm peripherals nrog rau SPI, LCD, Lub koob yees duab interface, UART, I2C, I2S, chaw taws teeb tswj, mem tes txee, LED PWM, USB Serial / JTAG maub los, MCPWM, SDIO party, GDMA, TWAI® maub los (tshaj ISO 11898-1), ADC, kov sensor, kub sensor, timers thiab watchdogs, nrog rau txog li 45 GPIOs. Nws kuj suav nrog kev ua haujlwm puv ceev USB 1.1 On-The-Go (OTG) interface kom pab USB kev sib txuas lus.
Pin lus txhais
Tus Pin Tso Tawm
tus pin daim duab siv tau rau ESP32-S3-WROOM-1 thiab ESP32-S3-WROOM-1U, tab sis tom kawg tsis muaj chaw khaws cia.
Pin Description
- Lub module muaj 41 tus pins. Saib tus pin txhais hauv Table 2.
- Rau kev piav qhia ntawm tus pin npe thiab cov npe ua haujlwm, nrog rau kev teeb tsa ntawm tus pins peripheral, thov mus rau ESP32-S3 Series Datasheet.
Table 2: Pin Definitions
| Lub npe | Tsis muaj. | Hom a | Muaj nuj nqi |
| GND | 1 | P | GND |
| 3v 3 | 2 | P | Fais fab mov |
|
EN |
3 |
I |
Siab: On enables lub nti. Tsawg: Lub chip fais fab tuag.
Lus Cim: Tsis txhob tso EN tus pin ntab. |
| IO4 | 4 | Kuv / O / T | RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3 |
| IO5 | 5 | Kuv / O / T | RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4 |
| IO6 | 6 | Kuv / O / T | RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5 |
| IO7 | 7 | Kuv / O / T | RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6 |
| IO15 | 8 | Kuv / O / T | RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P |
| IO16 | 9 | Kuv / O / T | RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N |
| IO17 | 10 | Kuv / O / T | RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6 |
| IO18 | 11 | Kuv / O / T | RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3 |
| IO8 | 12 | Kuv / O / T | RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1 |
| IO19 | 13 | Kuv / O / T | RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D- |
| IO20 | 14 | Kuv / O / T | RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+ |
| IO3 | 15 | Kuv / O / T | RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2 |
| IO46 | 16 | Kuv / O / T | GPIO 46 |
| IO9 | 17 | Kuv / O / T | RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD |
| IO10 | 18 | Kuv / O / T | RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4,
SUBSPICS 0 |
| IO11 | 19 | Kuv / O / T | RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5,
SUBSPID |
| IO12 | 20 | Kuv / O / T | RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6,
SUBSPICLK |
| IO13 | 21 | Kuv / O / T | RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7,
SUBSPIQ |
| IO14 | 22 | Kuv / O / T | RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS,
SUBSPIWP |
| IO21 | 23 | Kuv / O / T | RTC_GPIO21, GPIO21 |
| IO47 | 24 | Kuv / O / T | SPICLK_P_DIFF, GPIO47, SUBSPICLK_P_DIFF |
| IO48 | 25 | Kuv / O / T | SPICLK_N_DIFF, GPIO48, SUBSPICLK_N_DIFF |
| IO45 | 26 | Kuv / O / T | GPIO 45 |
| IO0 | 27 | Kuv / O / T | RTC_GPIO0, GPIO0 |
| IO35 b | 28 | Kuv / O / T | SPIIO6, GPIO35, FSPID, SUBSPID |
| IO36 b | 29 | Kuv / O / T | SPIIO7, GPIO36, FSPICLK, SUBSPICLK |
| IO37 b | 30 | Kuv / O / T | SPIDQS, GPIO37, FSPIQ, SUBSPIQ |
| IO38 | 31 | Kuv / O / T | GPIO38, FSPIWP, SUBSPIWP |
| IO39 | 32 | Kuv / O / T | MTCK, GPIO39, CLK_OUT3, SUBSPICS1 |
| IO40 | 33 | Kuv / O / T | MTDO, GPIO40, CLK_OUT2 |
| IO41 | 34 | Kuv / O / T | MTDI, GPIO41, CLK_OUT1 |
| Lub npe | Tsis muaj. | Hom a | Muaj nuj nqi |
| IO42 | 35 | Kuv / O / T | MTMS, GPIO42 |
| RXD 0 | 36 | Kuv / O / T | U0RXD, GPIO44, CLK_OUT2 |
| TX0 | 37 | Kuv / O / T | U0TXD, GPIO43, CLK_OUT1 |
| IO2 | 38 | Kuv / O / T | RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1 |
| IO1 | 39 | Kuv / O / T | RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0 |
| GND | 40 | P | GND |
| EPAD | 41 | P | GND |
- P: fais fab mov; kuv: input; O: tso zis; T: siab impedance. Pin functions nyob rau hauv bold font yog lub default pin functions.
- Hauv cov qauv sib txawv uas tau kos OSPI PSRAM, piv txwv li, uas kos ESP32-S3R8, pins IO35, IO36, thiab IO37 txuas rau OSPI PSRAM thiab tsis muaj rau lwm yam kev siv.
US FCC Nqe Lus
Cov cuab yeej no ua raws li Tshooj 15 ntawm FCC Cov Cai. Kev ua haujlwm yog ua raws li ob yam hauv qab no:
- Cov cuab yeej no yuav tsis ua teeb meem cuam tshuam.
- Cov cuab yeej no yuav tsum lees txais ib qho kev cuam tshuam tau txais, suav nrog kev cuam tshuam uas yuav ua rau kev ua haujlwm tsis xav tau.
Cov cuab yeej no tau raug sim thiab pom tias ua raws li cov kev txwv rau Class B cov cuab yeej digital, ua raws li Tshooj 15 ntawm FCC Cov Cai. Cov kev txwv no yog tsim los muab kev tiv thaiv tsim nyog tiv thaiv kev cuam tshuam tsis zoo hauv kev teeb tsa hauv tsev. Cov cuab yeej no tsim, siv, thiab tuaj yeem tawg lub zog ntawm xov tooj cua thiab, yog tias tsis tau nruab thiab siv raws li cov lus qhia, yuav ua rau muaj kev cuam tshuam rau kev sib txuas lus hauv xov tooj cua. Txawm li cas los xij, tsis muaj kev lees paub tias kev cuam tshuam yuav tsis tshwm sim hauv ib qho kev teeb tsa tshwj xeeb. Yog tias cov cuab yeej no ua rau muaj teeb meem cuam tshuam rau lub xov tooj cua lossis TV txais tos, uas tuaj yeem txiav txim siab los ntawm kev tig cov khoom siv thiab qhib, tus neeg siv tau raug txhawb kom sim kho qhov cuam tshuam los ntawm ib qho ntawm cov kev ntsuas hauv qab no:
- Reorient los yog tshem tawm cov kav hlau txais xov.
- Ua kom muaj kev sib cais ntawm cov khoom siv thiab lub receiver.
- Txuas cov cuab yeej mus rau lub qhov hluav taws xob ntawm ib lub voj voog sib txawv ntawm qhov uas lub receiver txuas nrog.
- Nrog rau tus neeg muag khoom lossis tus kws tshaj lij xov tooj cua / TV rau kev pab.
Ib qho kev hloov pauv lossis kev hloov kho uas tsis tau pom zoo los ntawm tog neeg lub luag haujlwm rau kev ua raws cai tuaj yeem ua rau tus neeg siv txoj cai ua haujlwm ntawm cov khoom siv.
Cov cuab yeej siv no ua raws li FCC RF kev txwv tsis pub muaj hluav taws xob tau teeb tsa rau qhov chaw tsis muaj kev tswj hwm. Cov cuab yeej no thiab nws cov kav hlau txais xov yuav tsum tsis txhob muab tso rau hauv los yog ua haujlwm ua ke nrog lwm tus kav hlau txais xov lossis cov khoom xa tawm. Cov kav hlau txais xov siv rau lub tshuab xa hluav taws xob no yuav tsum tau teeb tsa los muab kev sib cais ntawm qhov deb tsawg kawg 20 cm ntawm txhua tus neeg thiab yuav tsum tsis txhob sib koom ua ke lossis ua haujlwm ua ke nrog lwm tus kav hlau txais xov lossis cov khoom xa tawm.
Cov lus qhia kev koom ua ke OEM
- Cov cuab yeej no tsuas yog npaj rau OEM integrators raws li hauv qab no.
- Lub module tuaj yeem siv rau kev teeb tsa ntawm lwm tus tswv tsev.
- Lub kav hlau txais xov yuav tsum tau nruab xws li 20 cm yog khaws cia nruab nrab ntawm tus kav hlau txais xov thiab cov neeg siv, thiab lub transmitter module yuav tsis koom nrog lwm yam transmitter lossis kav hlau txais xov.
- Lub module yuav tsum tsuas yog siv nrog cov kav hlau txais xov tseem ceeb uas tau sim thawj zaug thiab tau lees paub nrog cov qauv no. Raws li ntev raws li 3 yam saum toj no tau ua tiav, tsis tas yuav tsum muaj kev xeem xa mus ntxiv.
- Txawm li cas los xij, OEM kev koom ua ke tseem yog lub luag haujlwm rau kev sim lawv cov khoom kawg rau ib qho kev ua raws cai ntxiv nrog rau cov qauv no tau nruab (rau example, digital device emission, PC peripheral requirements, thiab lwm yam)
Daim ntawv ceeb toom:
Yog tias cov xwm txheej no tsis tuaj yeem ua tau raws li (example, qee qhov kev teeb tsa lub khoos phis tawj lossis qhov chaw sib txuas nrog lwm lub tshuab xa tawm), tom qab ntawd FCC tso cai rau cov qauv no ua ke nrog cov khoom siv hauv tsev tsis suav tias siv tau lawm, thiab FCC ID ntawm lub module tsis tuaj yeem siv rau ntawm cov khoom kawg. Nyob rau hauv cov xwm txheej no thiab cov xwm txheej, tus neeg koom ua ke OEM yuav yog lub luag haujlwm rau rov ntsuas cov khoom kawg (suav nrog lub transmitter) thiab tau txais kev tso cai FCC cais.
End Product Labeling
Qhov no transmitter module tau tso cai tsuas yog siv rau hauv cov khoom siv uas lub kav hlau txais xov tuaj yeem ntsia tau zoo li 20 cm yuav khaws cia ntawm tus kav hlau txais xov thiab tus neeg siv. Cov khoom kawg kawg yuav tsum tau sau rau hauv qhov chaw pom nrog cov hauv qab no:
- "Nrog FCC ID: SAK-ESP32S3
- Lub Npe Lub Npe Kev Lag Luam (HMN) - Ntse pa taws / CO tswb
IC nqe lus
Cov cuab yeej no ua raws li Kev Lag Luam Canada daim ntawv tso cai-tsim RSSs. Kev ua haujlwm yog ua raws li ob yam hauv qab no:
• Cov cuab yeej no yuav tsis cuam tshuam, thiab
• Cov cuab yeej no yuav tsum lees txais txhua yam kev cuam tshuam, suav nrog kev cuam tshuam uas yuav ua rau tsis ua haujlwm ntawm lub cuab yeej.
Radiation Exposure Statement
Cov cuab yeej siv no ua raws li IC hluav taws xob raug txwv tsis pub dhau los rau qhov chaw tsis muaj kev tswj hwm. Cov cuab yeej no yuav tsum tau nruab thiab ua haujlwm nrog qhov tsawg kawg nkaus ntawm 20 cm ntawm lub radiator & koj
lub cev.
RSS247 Ntu 6.4 (5)
Cov cuab yeej tuaj yeem txiav txuas ntxiv mus yog tias tsis muaj cov ntaub ntawv xa mus lossis ua haujlwm tsis tiav. Nco ntsoov tias qhov no tsis yog lub hom phiaj txwv tsis pub kis tus tswj lossis xa cov ntaub ntawv lossis siv cov lej rov ua dua qhov xav tau los ntawm thev naus laus zis.
Cov cuab yeej no tsuas yog npaj rau OEM kev sib koom ua ke raws li cov hauv qab no: (Rau module siv)
- Lub kav hlau txais xov yuav tsum tau nruab xws li 20 cm yog tswj ntawm tus kav hlau txais xov thiab cov neeg siv, thiab
- Lub transmitter module yuav tsis koom nrog lwm lub transmitter lossis kav hlau txais xov.
Raws li ntev raws li 2 cov xwm txheej saum toj no tau ntsib, tsis tas yuav muaj kev sim ntsuas ntxiv. Txawm li cas los xij, OEM kev koom ua ke tseem yog lub luag haujlwm rau kev sim lawv cov khoom kawg rau ib qho kev ua raws cai ntxiv uas yuav tsum tau ua nrog cov qauv no.
CEEB TOOM:
Yog tias cov xwm txheej no tsis tuaj yeem ua tau raws li (example, qee qhov kev teeb tsa lub laptop lossis chaw nyob nrog lwm lub tshuab xa tawm), tom qab ntawd kev tso cai Canada tsis suav tias yog siv tau lawm, thiab IC ID tsis tuaj yeem siv rau ntawm cov khoom kawg. Nyob rau hauv cov xwm txheej no, tus OEM integrator yuav yog lub luag hauj lwm rau rov ntsuam xyuas cov khoom kawg (nrog rau lub transmitter) thiab tau txais ib tug cais Canada tso cai.
Qhov no transmitter module tau tso cai tsuas yog siv rau hauv cov khoom siv uas lub kav hlau txais xov tuaj yeem ntsia tau zoo li 20 cm yuav khaws cia ntawm tus kav hlau txais xov thiab tus neeg siv. Cov khoom kawg kawg yuav tsum tau sau rau hauv qhov chaw pom nrog cov hauv qab no:
- Muaj IC: 7145-ESP32S3.
- Lub Npe Lub Npe Kev Lag Luam (HMN) - Ntse pa taws / CO tswb
Cov Ntaub Ntawv Qhia Txog Tus Neeg Siv Kawg Lub OEM integrator yuav tsum paub tsis txhob muab cov ntaub ntawv rau cov neeg siv kawg hais txog yuav ua li cas rau nruab los yog tshem tawm no RF module nyob rau hauv tus neeg siv phau ntawv ntawm cov khoom kawg uas integrates no module. Cov neeg siv kawg phau ntawv yuav tsum suav tag nrho cov ntaub ntawv tswj hwm / ceeb toom raws li qhia hauv phau ntawv no.
Cov ntaub ntawv ntsig txog
- ESP32-S3 Series Datasheet – Specifications of the ESP32-S3 hardware.
- ESP32-S3 Technical Reference Manual - Cov ncauj lus kom ntxaws txog kev siv ESP32-S3 lub cim xeeb thiab cov khoom siv.
- ESP32-S3 Hardware Design Guidelines - Cov lus qhia yuav ua li cas koom ua ke ESP32-S3 rau hauv koj cov khoom kho vajtse.
- Daim ntawv pov thawj http://espressif.com/en/support/documents/certificates
- Cov ntaub ntawv hloov tshiab thiab hloov tshiab Ceeb Toom Subscription http://espressif.com/en/support/download/documents
Developer Zone
- ESP-IDF Programming Guide rau ESP32-S3 - Cov ntaub ntawv dav dav rau ESP-IDF txoj kev txhim kho.
- ESP-IDF thiab lwm yam kev txhim kho hauv GitHub. http://github.com/espressif
- ESP32 BBS Lub Rooj Sib Tham - Tus Kws Ua Haujlwm-rau-Engineer (E2E) Zej Zog rau cov khoom lag luam Espressif, qhov chaw koj tuaj yeem tshaj tawm cov lus nug, qhia kev paub, tshawb nrhiav tswv yim, thiab pab daws teeb meem nrog cov phooj ywg engineers. http://esp32.com/
- Phau ntawv ESP - Cov kev coj ua zoo tshaj plaws, cov khoom, thiab cov ntawv sau los ntawm Espressif folks. http://blog.espressif.com/
- Saib cov tabs SDKs thiab Demos, Apps, Tools, thiab AT Firmware. http://espressif.com/en/support/download/sdks-demos
Cov khoom
- ESP32-S3 Series SoCs - Tshawb xyuas tag nrho ESP32-S3 SoCs. http://espressif.com/en/products/socs?id=ESP32-S3
- ESP32-S3 Series Modules - Xauj los ntawm txhua qhov ESP32-S3-based modules. http://espressif.com/en/products/modules?id=ESP32-S3
- ESP32-S3 Series DevKits - Xauj tag nrho ESP32-S3-based devkits. http://espressif.com/en/products/devkits?id=ESP32-S3
- ESP Product Selector - Nrhiav Espressif cov khoom siv kho vajtse haum rau koj cov kev xav tau los ntawm kev sib piv lossis siv cov ntxaij lim dej. http://products.espressif.com/#/product-selector?language=en
Kev kho keeb kwm
| Hnub tim | Version | Tso ntawv sau tseg |
| 2021-10-29 Ib | v0.6 ua | Zuag qhia tag nrho hloov tshiab rau chip kho 1 |
| 2021-07-19 Ib | v0.5.1 ua | Kev tso tawm ua ntej, rau kev hloov kho nti 0 |
Tsis lees paub thiab Daim Ntawv Ceeb Toom Copyright
Cov ntaub ntawv hauv daim ntawv no, suav nrog URL cov ntaub ntawv, yuav raug hloov pauv yam tsis tau ceeb toom.
Tag nrho cov ntaub ntawv thib peb ntawm cov ntaub ntawv no tau muab raws li tsis muaj kev lav phib xaub ntawm nws qhov tseeb thiab qhov tseeb. TSIS TXAUS SIAB RAU COV NTAUB NTAWV NO rau nws cov khoom lag luam, tsis muaj kev cuam tshuam, kev nyab xeeb rau txhua lub hom phiaj tshwj xeeb, lossis tsis muaj kev lav phib xaub uas tshwm sim tawm ntawm txhua qhov kev tshaj tawm, SPORIFICATIONAMPLE.
Txhua qhov kev lav phib xaub, suav nrog kev lav phib xaub rau kev ua txhaum cai ntawm cov tswv cuab, hais txog kev siv cov ntaub ntawv hauv daim ntawv no tsis lees paub. Tsis muaj ntawv tso cai qhia los yog qhia, los ntawm estoppel los yog lwm yam, rau ib qho kev muaj tswv yim muaj cai tau tso cai ntawm no. Lub logo Wi-Fi Alliance Tus Tswv Cuab yog lub cim lag luam ntawm Wi-Fi Alliance. Lub logo Bluetooth yog lub cim lag luam ntawm Bluetooth SIG. Tag nrho cov npe lag luam, cov cim lag luam, thiab cov cim lag luam sau npe tau hais hauv daim ntawv no yog cov cuab yeej ntawm lawv cov tswv thiab tau lees paub ntawm no. Copyright © 2022 Espressif Systems (Shanghai) Co., Ltd. All rights reserved.
Hu rau
- Saib tab Cov Lus Nug Muag, Cov Lus Nug Txog Kev Tshawb Fawb, Circuit Schematic & PCB Tsim Review, Tau Samples (cov khw muag khoom hauv online), Ua Peb Cov Khoom Muag, Cov Lus Qhia & Cov Lus Qhia. http://espressif.com/en/contact-us/sales-questions
- www.espressif.com
FAQ
- Dab tsi yog qhov txawv ntawm ESP32-S3-WROOM-1 thiab ESP32-S3-WROOM-1U?
- Lub ntsiab sib txawv yog nyob rau hauv lub kav hlau txais xov configuration. ESP32-S3-WROOM-1 muaj PCB kav hlau txais xov, thaum ESP32-S3-WROOM-1U los nrog lub kav hlau txais xov sab nraud.
- Kuv puas tuaj yeem tawm EN tus pin ntab?
- Tsis yog, nws tsis pom zoo kom tawm EN tus pin ntab. Xyuas kom nws txuas nrog lub teeb liab siab lossis qis kom ua tau zoo lossis lov tes taw lub nti.
Cov ntaub ntawv / Cov ntaub ntawv
 |
ESPRESSIF ESP32-S3-WROOM-1 Development Board Bluetooth Module [ua pdf] Tus neeg siv phau ntawv ESP32S3WROOM1, ESP32S3WROOM1U, ESP32-S3-WROOM-1 Development Board Bluetooth Module, ESP32-S3-WROOM-1, Development Board Bluetooth Module, Board Bluetooth Module, Bluetooth Module |