EPH CONTROLS R27V2 2 Zone Programmer Cov Neeg Siv Khoom Qhia

Cov lus qhia installation:
Kev teeb tsa thiab kev sib txuas yuav tsum tsuas yog ua los ntawm tus neeg tsim nyog. Ua ntej pib lub installation, disconnect tus programmer los ntawm lub mains. Tus programmer tuaj yeem ua tau nto-mounted lossis mounted rau hauv lub thawv recessed conduit. Ua raws li cov chaw tsim khoom cov lus qhia rau kev txhim kho kom raug.

Cov lus qhia ua haujlwm:

Kev Taw Qhia Ceev rau koj tus programmer R27V2: ntu no muab ib qho dhauview ntawm cov yam ntxwv tseem ceeb thiab kev ua haujlwm ntawm tus programmer.

Hom Kev Xaiv: Kawm paub yuav ua li cas taug qab thiab xaiv cov hom sib txawv ntawm tus programmer rau ntau qhov chaw.
Programming Modes: Nkag siab txog qhov sib txawv programming hom muaj thiab yuav teeb lawv li cas raws li koj nyiam.

Factory Program Settings: Tau txais kev paub txog qhov chaw pib ntawm tus programmer thiab yuav kho li cas yog tias xav tau.
Kho qhov Kev Pabcuam Teebmeem hauv 5/2 Hnub Hom: Cov lus qhia ib kauj ruam-ib-kauj ruam ntawm yuav hloov kho qhov program li cas hauv 5/2 hnub hom.

Reviewnyob rau hauv qhov Program Settings: Kawm yuav ua li cas rovview thiab txheeb xyuas qhov programmed nqis ntawm cov zaub.
Boost Function: Nkag siab txog kev siv lub zog txhawb kom muaj txiaj ntsig zoo rau kev xav tau cua sov los yog txias.

Kev Ua Haujlwm Ua Ntej: Tshawb nrhiav cov haujlwm siab heev ntawm tus programmer rau kev teeb tsa ntau dua.

Ntawv qhia zaub mov:
P01 Teem Lub Hnub, Lub Sijhawm, thiab Kev Ua Haujlwm Hom: Cov lus qhia ntxaws txog yuav ua li cas teem hnub, sijhawm, thiab hom kev ua haujlwm ntawm tus programmer.

FAQ:

Q: Kuv puas tuaj yeem nruab tus programmer kuv tus kheej?
A: Kev teeb tsa thiab kev sib txuas yuav tsum tsuas yog ua los ntawm tus neeg tsim nyog. Nws raug nquahu kom nrhiav kev pab los ntawm tus kws tshaj lij hluav taws xob tsim nyog lossis cov neeg ua haujlwm tau tso cai rau kev teeb tsa.

Q: Kuv yuav rov pib lub programmer li cas?
A: Txhawm rau rov pib dua tus programmer, ua raws li cov lus qhia hauv tus neeg siv phau ntawv. Koj tuaj yeem ua qhov kev pib dua tshiab lossis rov pib dua qhov tshwj xeeb raws li xav tau.

Factory Default Settings

Hu rau: 230 VAC ua

Txoj Haujlwm: 5 / 2D
Backlight: On

Keypad Xauv: Tawm
Kev Tiv Thaiv Frost: Tawm

Kev ua haujlwm hom: Auto
Pin Lock: Tawm
Lub Sijhawm Kev Pabcuam: Tawm
Zone Title: KEV KUB HEEV

Specifications

Fais fab mov: 230 VAC ua
Ambient Kub: 0… 50°C
Qhov Loj: 161 x 100 x 31 mm
Tiv tauj Rating: 3(1)A
Program Memory 5 Xyoo
Kub Sensor: NTC 100 K
Backlight: Dawb
Kev ntsuas IP: IP20
Roj teeb: 3VDC Lithium LIR2032 thiab CR2032
Backplate: British System Standard
Pollution degree: 2 (Resistance to voltage surge 2000V; Raws li EN60730)
Chav Kawm Software: Chav Kawm A

LCD zaub

Qhia txog lub sijhawm tam sim no.

Qhia hnub tam sim no ntawm lub lim tiam.
Qhia tau thaum qhib kev tiv thaiv Frost.
Qhia thaum lub keypad kaw.

Qhia hnub tam sim no.
Qhia cov npe ntawm cheeb tsam.
Qhia hom tam sim no.

Khawm Description

Kab kos duab

Kev sib txuas ntawm Terminal

Lub ntiaj teb
N nruab nrab

L Nyob
1 Zone 1 OFF - N / C Nquag kaw kev sib txuas
2 Zone 2 OFF - N / C Nquag kaw kev sib txuas

3 Zone 1 ON – N/O Nquag qhib kev sib txuas
4 Zone 2 ON – N/O Nquag qhib kev sib txuas

Mounting & Installation

Ceev faj!

Kev teeb tsa thiab kev sib txuas yuav tsum tsuas yog ua los ntawm tus neeg tsim nyog.
Tsuas yog cov kws tsim hluav taws xob tsim nyog lossis cov neeg ua haujlwm pabcuam tau tso cai qhib qhov program.

Yog hais tias tus programmer siv nyob rau hauv ib txoj kev uas tsis tau teev los ntawm cov chaw tsim tshuaj paus, nws txoj kev nyab xeeb tej zaum yuav impaired.
Ua ntej teeb tsa tus programmer, nws yuav tsum ua kom tiav tag nrho cov kev xav tau uas tau piav qhia hauv ntu no.
Ua ntej pib kev teeb tsa, tus programmer yuav tsum tau ua ntej txiav tawm ntawm lub mains.

Qhov programmer no tuaj yeem ua rau saum npoo los yog mounted rau lub thawv ntim khoom.

Tshem tawm tus programmer los ntawm nws lub ntim.
Xaiv qhov chaw mounting rau tus programmer:
- Mount tus programmer 1.5 meters saum toj no theem.
- Tiv thaiv kom tsis txhob raug tshav ntuj ncaj qha lossis lwm qhov chaw cua sov / cua txias.
Siv Philips ntswj ntsia hlau los xoob cov ntsia hlau ntawm lub nraub qaum nyob rau hauv qab ntawm tus programmer.
Tus programmer yog nqa mus rau hauv qab thiab tshem tawm ntawm lub backplate.

Screw lub backplate mus rau ib lub thawv recessed conduit los yog ncaj qha mus rau saum npoo.
Xaim lub backplate raws li daim duab kos duab.
Zaum tus programmer rau ntawm lub nraub qaum kom paub tseeb tias tus programmer pins thiab cov neeg sib txuas ntawm lub nraub qaum yog ua kom muaj suab sib txuas, thawb tus programmer flush rau saum npoo thiab ceev cov screws ntawm backplate los ntawm hauv qab.

Cov lus qhia ua haujlwm

Programmer

Kev taw qhia ceev rau koj tus programmer R27V2:

R27V2 programmer yuav siv los tswj ob thaj chaw sib cais hauv koj lub hauv paus cua sov.
Txhua cheeb tsam tuaj yeem ua haujlwm ntawm nws tus kheej thiab programmed kom haum rau koj cov kev xav tau. Txhua cheeb tsam muaj txog peb qhov kev siv cua sov txhua hnub hu ua P1, P2 thiab P3. Saib Page 13 rau cov lus qhia yuav ua li cas kho qhov program nqis.

Ntawm lub vijtsam LCD ntawm koj tus programmer koj yuav pom ob ntu cais, ib qho los sawv cev rau txhua cheeb tsam.
Nyob rau hauv cov seem no, koj tuaj yeem pom hom twg hauv cheeb tsam tam sim no.
Thaum nyob rau hauv AUTO hom, nws yuav qhia thaum thaj tsam yog tom ntej programmed kom hloov ON lossis OFF.

Rau 'Kev Xaiv Hom' thov mus saib nplooj 11 kom piav qhia ntxiv.
Thaum thaj tsam ON, koj yuav pom cov LED liab rau thaj tsam ntawd teeb. Qhov no qhia tau hais tias lub zog raug xa los ntawm tus programmer hauv cheeb tsam no.

Hom Xaiv AUTO
Muaj plaub hom muaj rau xaiv.

AUTO Lub cheeb tsam ua haujlwm txog peb lub sijhawm 'ON / OFF' ib hnub (P1, P2, P3).
TAG NRHO HNUB Lub cheeb tsam ua haujlwm ib lub sijhawm 'ON/OFF' ib hnub. Qhov no ua haujlwm los ntawm thawj 'ON' lub sijhawm mus rau thib peb 'OFF' lub sijhawm.
ON Lub cheeb tsam yog mus tas li ON.

OFF Lub cheeb tsam yog mus tas li OFF.
Nias Xaiv los hloov ntawm AUTO, TXHUA HNUB, ON & OFF.
Hom tam sim no yuav pom ntawm lub vijtsam hauv qab thaj tsam tshwj xeeb.

Qhov Xaiv muaj nyob hauv qab lub hau npog. Txhua cheeb tsam muaj nws tus kheej Xaiv.

Programming Hom

Cov programmer no muaj cov programming hauv qab no.

5/2 Hnub hom Programming Monday txog Friday ua ib qho thaiv thiab hnub Saturday thiab hnub Sunday raws li 2nd block.

7-Day hom Programming tag nrho 7 hnub ib tus zuj zus.
24-teev hom Programming tag nrho 7 hnub ua ib qho thaiv.

Factory Program Settings 5/2 d

Kho qhov program teeb tsa hauv 5/2 Hnub Hom

Xovxwm PROG.

Programming rau hnub Monday txog Friday rau Zone 1 yog tam sim no xaiv.

Txhawm rau hloov cov programming rau Zone 2, nias qhov tsim nyog xaiv.
Nias + thiab - txhawm rau kho P1 ON lub sijhawm. Nias OK.

Nias + thiab - los kho lub sijhawm P1 OFF. Nias OK.
Rov ua cov txheej txheem no los kho P2 thiab P3 zaug.

Programming rau hnub Saturday txog hnub Sunday yog tam sim no xaiv.

Nias + thiab - txhawm rau kho P1 ON lub sijhawm. Nias OK.
Nias + thiab - los kho lub sijhawm P1 OFF. Nias OK.
Rov ua cov txheej txheem no los kho P2 thiab P3 zaug.

Nias MENU kom rov qab mus ua haujlwm li qub.
Thaum nyob rau hauv hom programming, nias Xaiv yuav dhia mus rau hnub tom ntej (block of days) yam tsis hloov qhov program.

Nco tseg:

Txhawm rau hloov ntawm 5/2d mus rau 7D lossis 24H programming, xa mus rau nplooj 16, Ntawv qhia zaub mov P01.
Yog tias koj tsis xav siv ib lossis ntau dua ntawm cov kev pabcuam txhua hnub ces tsuas yog teem sijhawm pib thiab sijhawm kawg kom zoo ib yam. Rau example, yog P2 tau teem caij pib thaum 1 tav su thiab xaus rau 1 tav su programmer yuav tsuas tsis quav ntsej txog qhov kev pab cuam no thiab mus rau lub sijhawm hloov tom ntej.

Reviewhauv qhov Program Settings

Nias PROG.

Nias OK mus hla cov sij hawm rau ib hnub (block of days).
Nyem Xaiv kom dhia mus rau hnub tom ntej (block of days).
Nias MENU kom rov qab mus ua haujlwm li qub.

Koj yuav tsum nias qhov tshwj xeeb Xaiv kom rovview lub sij hawm rau cheeb tsam ntawd.

Boost Function
Txhua cheeb tsam tuaj yeem txhawb nqa rau 30 feeb, 1, 2 lossis 3 teev thaum thaj chaw nyob hauv AUTO, TAG NRHO HNUB & OFF hom.

Nias Boost 1, 2, 3 lossis 4 zaug, txhawm rau siv lub sijhawm BOOST xav tau rau thaj tsam.

Thaum lub Boost raug nias muaj 5-thib ob ncua ua ntej qhib qhov twg 'BOOST' yuav nyem rau ntawm lub vijtsam, qhov no muab sijhawm rau tus neeg siv los xaiv lub sijhawm BOOST xav tau.
Txhawm rau tshem tawm BOOST, nias qhov Boost dua.
Thaum lub sijhawm BOOST tau xaus lossis raug muab tso tseg, Cheeb Tsam yuav rov qab mus rau hom uas tau ua dhau los ua ntej BOOST.

Nco tseg: Lub BOOST tsis tuaj yeem siv tau thaum nyob hauv ON lossis Hnub So.

Ua ntej muaj nuj nqi

Thaum ib cheeb tsam nyob hauv AUTO lossis ALLDAY hom, Kev Ua Haujlwm Ua Ntej tso cai rau tus neeg siv coj thaj chaw lossis thaj chaw rau pem hauv ntej mus rau lub sijhawm hloov tom ntej.

Yog tias cheeb tsam tam sim no tau teem sijhawm rau OFF thiab ADV raug nias, thaj tsam yuav raug hloov mus txog thaum kawg ntawm lub sijhawm hloov tom ntej. Yog tias cheeb tsam tam sim no tau teem sijhawm rau ON thiab ADV raug nias, thaj tsam yuav raug hloov OFF kom txog thaum pib ntawm lub sijhawm hloov tom ntej.

Nias ADV.
Zone 1 thiab Zone 2 yuav pib flash.
Nyem qhov tsim nyog xaiv.

Lub cheeb tsam yuav tso saib 'ADVANCE ON' lossis 'ADVANCE OFF' kom txog thaum kawg ntawm lub sijhawm hloov tom ntej.
Zone 1 yuav nres flashing thiab nkag mus rau hom ua ntej.
Zone 2 yuav nyob twj ywm flashing.

Rov ua cov txheej txheem no nrog Zone 2 yog tias xav tau.
Nias OK.
Txhawm rau rho tawm ADVANCE, nias qhov tsim nyog xaiv.

Thaum lub sijhawm ADVANCE tau xaus lossis raug tshem tawm, thaj chaw yuav rov qab mus rau hom uas tau ua dhau los ua ntej ADVANCE.

Ntawv qhia zaub mov

Cov ntawv qhia zaub mov no tso cai rau tus neeg siv los kho cov haujlwm ntxiv.
Txhawm rau nkag mus rau cov ntawv qhia zaub mov, nias MENU .

P01 Teem Lub Hnub, Lub Sijhawm thiab Hom Kev Ua Haujlwm DST RAU

Nyem MENU, 'P01 tInE' yuav tshwm sim ntawm qhov screen.
Nias OK, thiab lub xyoo yuav pib flash.

Nias + thiab – kho lub xyoo. Nias OK.
Nias + thiab – hloov lub hli. Nias OK.
Nias + thiab - los kho lub hnub. Nias OK.

Nias + thiab – kho lub teev. Nias OK.
Nias + thiab – los kho lub feeb. Nias OK.
Nias + thiab – hloov ntawm 5/2d rau 7d lossis 24h hom. Nias OK.

Nias + thiab – tig DST (Hnub Teeb Txuag Sijhawm) On lossis Off.
Nias MENU thiab tus programmer yuav rov qab mus ua haujlwm li qub.

Nco tseg:
Thov mus saib nplooj ntawv 12 rau cov lus piav qhia ntawm Cov Kev Pabcuam Hom.

P02 Hnub so hom
Cov ntawv qhia zaub mov no tso cai rau tus neeg siv los hloov lawv cov cua sov los ntawm kev txhais hnub pib thiab hnub kawg.

Nyem MENU, 'P01' yuav tshwm sim ntawm qhov screen.
Nias + kom txog thaum 'P02 HOL' yuav tshwm sim ntawm qhov screen.
Nias OK, 'HOLIDAY FROM', thiab hnub thiab sijhawm yuav tshwm sim ntawm qhov screen. Lub xyoo yuav pib tshauv.
Nias + thiab – kho lub xyoo. Nias OK.
Nias + thiab – hloov lub hli. Nias OK.
Nias + thiab - los kho lub hnub. Nias OK.
Nias + thiab – kho lub teev. Nias OK.
'HOLIDAY TO' thiab hnub thiab sijhawm yuav tshwm sim ntawm qhov screen. Lub xyoo yuav pib tshauv.
Nias + thiab – kho lub xyoo. Nias OK.
Nias + thiab – hloov lub hli. Nias OK.
Nias + thiab - los kho lub hnub. Nias OK.
Nias + thiab – kho lub teev. Nias OK.
Tam sim no tus programmer yuav raug kaw thaum lub sijhawm xaiv no.
Txhawm rau tshem tawm HOLIDAY, nias OK.

Tus programmer yuav rov ua haujlwm li qub thaum hnub so tiav lossis raug tshem tawm.

P03 Frost tiv thaiv OFF
Cov ntawv qhia zaub mov no tso cai rau tus neeg siv los qhib kev tiv thaiv Frost ntawm thaj tsam ntawm 5 ° C thiab 20 ° C.

Frost tiv thaiv yog lub neej ntawd teem rau OFF.
Nyem MENU, 'P01' yuav tshwm sim ntawm qhov screen.
Nias + kom txog thaum 'P03 FrOST' tshwm ntawm qhov screen.
Nias OK, thiab 'OFF' yuav tshwm sim ntawm qhov screen.
Nias + xaiv 'ON'. Nias OK.
'5 ° C' yuav nyem ntawm qhov screen.
Nias + thiab - xaiv qhov koj xav tau Frost tiv thaiv kub. Nias OK.
Nias MENU thiab tus programmer yuav rov qab mus ua haujlwm li qub.

Lub cim Frost yuav tso tawm ntawm qhov screen yog tias tus neeg siv qhib nws hauv cov ntawv qhia zaub mov.

Yog hais tias chav tsev kub kub poob qis dua qhov xav tau Frost tiv thaiv qhov kub thiab txias, txhua qhov chaw ntawm tus programmer yuav qhib thiab lub cim Frost yuav nyem kom txog thaum lub Frost tiv thaiv qhov kub thiab txias tau tiav.

P04 Zone Title
Cov ntawv qhia zaub mov no tso cai rau tus neeg siv xaiv cov npe sib txawv rau txhua cheeb tsam.

Cov kev xaiv yog:

DEFAULT OPTIONS	RENAME OPTIONS
HLOOV	ZAJ 1
KEV KUB	ZAJ 2

Nyem MENU, 'P01' yuav tshwm sim ntawm qhov screen.
Nias + kom txog rau thaum 'P04' tshwm ntawm qhov screen.
Nias OK, 'KUB dej' yuav nyem rau ntawm qhov screen.
Nias + hloov los ntawm 'KUB dej' mus rau 'ZONE 1'. Nias OK. 'XEEM' yuav nyem rau ntawm qhov screen.
Nias + hloov los ntawm 'HEATING' rau 'ZONE 2'.
Nias MENU thiab tus programmer yuav rov qab mus ua haujlwm li qub.

P05 PIN

Cov ntawv qhia zaub mov no tso cai rau tus neeg siv tso tus lej PIN rau ntawm tus programmer.
Tus PIN xauv yuav txo qhov kev ua haujlwm ntawm tus programmer.

Teeb tus PIN

Nyem MENU, 'P01' yuav tshwm sim ntawm qhov screen.
Nias kom txog thaum 'P05 PIN' tshwm ntawm qhov screen.
Nias OK, thiab 'OFF' yuav tshwm sim ntawm qhov screen.
Nias kom hloov los ntawm OFF rau ON. Nias OK. '0000' yuav nyem rau ntawm qhov screen.
Nias thiab teeb tus nqi ntawm 0 txog 9 rau thawj tus lej. Nias OK kom txav mus rau tus lej PIN tom ntej.
Thaum tus lej kawg ntawm tus PIN raug teeb tsa, nias OK. Txheeb xyuas yog tso tawm nrog '0000'.
Nias thiab teeb tus nqi ntawm 0 txog 9 rau thawj tus lej. Nias OK kom txav mus rau tus lej PIN tom ntej.
Thaum tus lej kawg ntawm tus PIN raug teeb tsa, nias OK. Tus PIN tam sim no tau txheeb xyuas, thiab tus PIN xauv tau qhib.
Yog tias tus lej PIN nkag mus tsis raug, tus neeg siv yuav raug coj rov qab mus rau cov ntawv qhia zaub mov.
Thaum tus PIN ntsuas phoo siv tau lub cim Xauv yuav nyem txhua ob lub vib nas this ntawm qhov screen.
Thaum tus programmer kaw tus lej PIN, nias cov ntawv qhia zaub mov yuav coj tus neeg siv mus rau PIN xauv npo.

Nco tseg:

Thaum lub xauv PIN qhib, BOOST lub sij hawm raug txo mus rau 30-feeb thiab 1-teev sij hawm.
Thaum lub xauv PIN qhib, Hom Kev Xaiv raug txo qis rau Auto thiab OFF.

Xauv tus PIN

Nyem MENU, 'UNLOCK' yuav tshwm sim ntawm qhov screen. '0000' yuav nyem rau ntawm qhov screen.
Nyem + thiab - txhawm rau teeb tsa tus nqi ntawm 0 txog 9 rau thawj tus lej.
Nias OK kom txav mus rau tus lej PIN tom ntej.
Thaum tus lej kawg ntawm tus PIN raug teeb tsa. Nias OK.
Tus PIN tam sim no tau xauv lawm.

Yog tias tus PIN tau raug xauv ntawm tus programmer, nws yuav rov qhib dua yog tias tsis muaj khawm nias rau 2 feeb.

Txhawm rau Deactivate tus PIN
Thaum tus PIN qhib lawm (saib cov lus qhia saum toj no)

Nyem MENU, 'P01' yuav tshwm sim ntawm qhov screen.
Nias kom txog thaum 'P05 PIN' tshwm ntawm qhov screen.
Nias OK, 'ON' yuav tshwm sim ntawm qhov screen.
Nias los yog xaiv 'OFF'. Nias OK.
'0000' yuav nyem rau ntawm qhov screen. Sau tus PIN. Nias OK.
Tus PIN tam sim no raug kaw lawm.

Nias MENU kom rov qab mus ua haujlwm li qub lossis nws yuav cia li tawm tom qab 20 vib nas this.

Copy Function

Daim ntawv ua haujlwm tsuas yog siv tau thaum xaiv 7D hom. (Saib nplooj 16 los xaiv 7d hom) Nias PROG los ua qhov ON thiab OFF lub sijhawm rau hnub rau lub lim tiam koj xav luam.

Tsis txhob nias OK ntawm lub sijhawm P3 OFF, tawm lub sijhawm no flashing.

Nias ADV, thiab 'COPY' yuav tshwm sim ntawm qhov screen, nrog rau hnub tom ntej ntawm lub lim tiam flashing.
Txhawm rau ntxiv cov sijhawm xav tau rau hnub no nias +.
Hla hnub no nias -.
Nias OK thaum lub sij hawm tau siv rau cov hnub xav tau.
Xyuas kom lub cheeb tsam nyob rau hauv Auto hom rau lub sij hawm no ua hauj lwm raws li.
Rov ua cov txheej txheem no rau Zone 2 yog tias xav tau.

Nco tseg:
Koj tsis tuaj yeem luam cov sij hawm los ntawm ib cheeb tsam mus rau lwm qhov, xws li Luam theej lub sij hawm Zone 1 mus rau Zone 2 tsis tuaj yeem ua tau.

Backlight Hom Xaiv ON
Muaj 3 qhov teeb tsa backlight muaj rau xaiv:

AUTO Backlight nyob twj ywm rau 10 vib nas this thaum ib lub pob raug nias.
ON Backlight yog mus tas li On.
Lub backlight yog mus tas li Off.
Txhawm rau kho lub teeb nyem nyem thiab tuav OK rau 10 vib nas this.
'Auto' tshwm ntawm qhov screen.
Nias + lossis – hloov hom ntawm Auto, On thiab Off.
Nias OK kom paub meej tias xaiv thiab rov qab mus ua haujlwm li qub.

Xauv lub Keypad

Txhawm rau kaw tus programmer, nias thiab tuav + thiab - ua ke rau 10 vib nas this.
yuav tshwm sim ntawm qhov screen. Cov nyees khawm tam sim no raug kaw.
Txhawm rau qhib tus programmer, nias thiab tuav + thiab - rau 10 vib nas this.
yuav ploj ntawm qhov screen. Cov nyees khawm tam sim no tau qhib.

Resetting tus Programmer

Txhawm rau rov pib dua tus programmer rau lub Hoobkas teeb tsa:

Nias MENU.
'P01' yuav tshwm sim ntawm qhov screen.
Nias + kom txog rau thaum 'P06 rESET' tshwm ntawm qhov screen.
Nias OK xaiv.
'Tsis yog' yuav pib flash.
Nias +, hloov ntawm 'nO' rau 'YES'.
Nias OK kom paub meej.
Tus programmer yuav rov pib dua thiab rov qab mus rau nws lub Hoobkas-txhais chaw.
Lub sijhawm thiab hnub tim yuav tsis rov pib dua.

Master Reset

Txhawm rau rov pib dua tus programmer mus rau lub Hoobkas, nrhiav tus tswv pib dua khawm ntawm sab xis sab xis hauv qab tus programmer.
Nias lub Master Reset khawm thiab tso nws.
Qhov screen yuav ploj mus thiab reboot.
Tus programmer yuav rov pib dua thiab rov qab mus rau nws lub Hoobkas-txhais chaw.

Lub Sijhawm Kev Pabcuam

Lub Sijhawm Kev Pabcuam OFF
Lub sijhawm pabcuam muab lub peev xwm los tso lub sijhawm suav rov qab txhua xyoo ntawm tus programmer. Thaum Lub Sij Hawm Kev Pabcuam tau qhib 'SErv' yuav tshwm sim ntawm qhov screen uas yuav ceeb toom rau tus neeg siv tias lawv qhov kev pabcuam boiler txhua xyoo yuav dhau los.

Yog xav paub ntxiv txog yuav ua li cas thiaj li pab tau lossis lov tes taw Service Interval, thov hu rau cov neeg siv khoom.

EPH tswj IE

EPH Tswj UK

Cov ntaub ntawv / Cov ntaub ntawv

EPH CONTROL R27V2 2 Zone Programmer [ua pdf] Cov neeg siv phau ntawv qhia
R27V2 2 Zone Programmer, R27V2 2, Zone Programmer, Programmer

Cov ntaub ntawv

Cov neeg siv phau ntawv

EPH CONTROL R27V2 2 Zone Programmer

Cov ntaub ntawv khoom

Cov lus qhia siv khoom