ARDUINO RFLINK-Mix Wireless UART rau IO Module
RFLINK-Mix Wireless UART-rau-IO yog ib qho yooj yim-rau-siv module uas tso cai rau cov neeg siv ceev ceev teeb tsa cov chaw taws teeb IO. Koj tsis tas yuav teeb tsa ntau cov cables ntev raws li qhov dav dav dav hlau IO suite ua, koj tsuas yog yuav tsum txuas UART ROOT board ntawm RFLINL-Mix rau lub rooj tsavxwm tswv (Arduino, Raspberry Pi, lwm yam HOST), thiab IO. ntaus ntawv ntawm RFLINK-Mix rau IO pab kiag li lawm, ces lub wireless IO system yog npaj mus. Txhua lub rooj tsavxwm IO muaj 3 pawg ntawm IO chaw nres nkoj, yog li 1-rau-4 RFLINK-Mix UART rau IO suite tuaj yeem tswj tau 12 teeb ntawm IO chaw nres nkoj.
Module tsos thiab dimension
RFLINK-Mix UART-rau-IO module muaj ib daim ntawm UART ROOT kawg (sab laug). Txog li plaub IO Devices (sab xis ntawm daim duab hauv qab no, suav nrog 0 txog 3), ob qho tib si Txawm hais tias qhov zoo li qub, nws tuaj yeem txheeb xyuas tau los ntawm daim ntawv lo rau sab nraum qab ntawm ROOT lossis DEVICE Kos lub thawv kom paub meej.
Raws li pom hauv daim duab hauv qab no, daim duab sab laug yog sab sab, thiab lwm yam yog daim ntawv lo sab Lub Chaw Nyob ntawm pawg no ntawm RFLINK-UARTROOT modules yog 0001, Baud tus nqi 19200. RFLINK I2C Devices as Device 0, Device 1, Ntaus 2, Ntaus 3, Pawg Chaw Nyob yog 0003
Module yam ntxwv
- Kev khiav hauj lwm voltage: 3.3 ~ 5.5V
- RF zaus: 2400MHz ~ 2480MHz.
- Kev siv hluav taws xob: Kev xa tawm txog 24 mA @ + 5dBm thiab tau txais txog 23mA.
- Kev xa hluav taws xob: + 5dBm
- Kev sib kis nrug: txog 80 mus rau 100m hauv qhov chaw qhib
- Baud tus nqi (UART ROOT): 9,600bps lossis 19,200bps
- Medidas: 25 mm x 15 mm x 2 mm (LxWxH)
- Kev sib xyaw ntawm 1-rau-1 lossis 1-rau-ntau (txog plaub) IO Device Modules tau txais kev txhawb nqa mus txog 12 pawg IO, 1-rau-ntau siv hauv hom lus txib nrog cov lus txib kom xaiv cov cuab yeej Module hloov nrog. .
Pin txhais
| UA ROOT
|
IO KEV
|
| GNDyog av + 5 Vyog 5v vtage tswv yim The TXè sib raug rau RX ntawm motherboard UART Lub RXè sib raug rau TX ntawm motherboard UART THE CEBè PIN REQUIREs a grounding (GND) module ua haujlwm fais fab thiab tuaj yeem siv los ua lub zog txuag hluav taws xob. TawmIE IO Port Export Pin (On/Off Export) è Cov tswv yim tus pin ntawm IN IO Chaw nres nkoj (On/Off txais). CMD_Modeyog ROOT rau kev hais kom ua hom pib tus pin, nquag qis |
GNDyog av + 5 Vyog 5v vtage tswv yim ib 0è Input pin (On/Off txais) rau pab pawg 0 IO Ports OUT0Pawg 0 IO Chaw nres nkoj Export Pin (On/Off Export) ib 1è Input pin (On/Off txais) rau pab pawg 1 IO Ports OUT1Teeb 1 IO Chaw Nres Nkoj Export Pin (On/Off Export) ib 2è Input pin (On/Off txais) rau pab pawg 2 IO Ports OUT2Pawg 2 IO Chaw nres nkoj Export Pin (On/Off Export) THE CEBè PIN REQUIREs a grounding (GND) module ua haujlwm fais fab thiab tuaj yeem siv los ua kev tswj fais fab. muaj nuj nqi. |
Yuav siv li cas
Koj tuaj yeem siv qhov module RFLINK-Mix UART-rau-IO los tswj ntau pawg ntawm relays kom ua tiav wireless tsis siv neeg tswj.
RFLINK-Mix UART-rau-IO siv examples tuaj yeem rub tawm los ntawm official webqhov chaw http://www.sunplusit.com/TW/Shop/IoT/Document.
Cov ntaub ntawv / Cov ntaub ntawv
 |
ARDUINO RFLINK-Mix Wireless UART rau IO Module [ua pdf] Tus neeg siv phau ntawv RFLINK-Mix, Wireless UART rau IO Module, RFLINK-Mix Wireless UART rau IO Module |
